Investigation of effect of filler on mechanical properties of fiber reinforced polymer matrix composites
Dolgu maddelerinin polimer matrisli kompozitlerin mekanik özelliklerine etkilerinin incelenmesi
- Tez No: 93379
- Danışmanlar: PROF. DR. ÖMER GÜNDÜZ BİLİR, DOÇ. DR. LEVEND PARNAS
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Hibrid kompozitleri, tanecikli kompozitleri, çekme dayanımı, eğme dayanımı, eğme modülü, darbe direnç, tanecikleri vı, Dolgu maddeleri, Eğilme dayanımı, Mekanik özellikler, Polimer kompozitler, Hybrid composites, particulate composites, tensile strength, bending strength, bending (flexural) modulus, impact resistance, filler IV, Fillers, Mechanical properties, Polymer composites
- Yıl: 2000
- Dil: İngilizce
- Üniversite: Orta Doğu Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
oz DOLGU MADDELERİNİN POLİMER MATRİSLİ KOMPOZİTLERİN MEKANİK ÖZELLİKLERİNE ETKİLERİNİN İNCELEMESİ Ligata, Haris Yüksek Lisans, Makine Mühendisliği Bölümü Tez Yöneticisi: Prof. Dr. Ömer Gündüz Bilir Ortak Tez Yöneticisi: Doç. Dr. Levend Parnas Nisan 2000, 123 sayfa Bu tez çalışmasında, tanecikli katkı maddelerinin elyaf takviyeli polimer matris kompozitlerin mekanik özellikleri üstündeki etkisi araştırılmıştır. Çekme ve eğme dayanımları, darbe direnç ve eğme modülü gibi mekanik özellikler çalışmanın parametrelerini oluşturmaktadır. Bu özelliklerdeki değişikliği gözlemleyebilmek için çekme, eğme ve darbe deneyleri yapılmıştır. Bu testler için iki farklı türde kuponlar hazırlanmıştır. Kuponların hazırlamasında RTM metodu kulanılmıştır. İki farklı sistem (sadece tozla desteklenmiş olan matris, ve hem toz hem de elyafla desteklenmiş matris) için tanecik etkisi mekanik özellikleri gözlemleyerek araştırılmıştır. Bu çalışmada üç değişik türde tanecik (Ti02, Al203 ve CaC03) değiştirilmeden kullanılmıştır.Elde edilen verilere göre, tanecik eklenmesi sonucu çekme ve eğme dayanımlarında ilk başta artış görülürken, daha fazla miktarlar için azalma gözlenmeiştir. Baştaki artışın crack pinning ve branching dolayı olduğu düşünülmektedir. Eğme modülü her iki sistem ( sadece tanecikli ve hibrid kompozitler) için de artış göstermiştir. Matris daha katı bir hal aldığı için bu beklenen bir sonuçtur. İki sistemde de taneciklerin ağırlık (veya hacim) oranının artmasıyla darbe direncinde azalma görülmüştür. Bunun nedeni taneciklerin ağırlık oranının artamasıyla oluşan gerilme yoğunlaşmasıdır. Tanecikli kompozitlerin davranışı teorik denklemlerle elde edilen sonuçlarla uygundur. Hibrid kompozitler için, deneysel sonuçlarla yarı deneysel deklemler kullanılarak elde edilen sonuçların farklı olduğu gözlemlenmiştir. Beklenen ve gözlemlenen davranışlar arasındaki farkın denklemlerde crack pining ve branching davranışlarının gözönüne alınmamasından dolayı olduğu düşünülmektedir.
Özet (Çeviri)
ABSTRACT INVESTIGATION OF EFFECT OF FILLER ON MECHANICAL PROPERTIES OF FIBER REINFORCED POLYMER MATRIX COMPOSITES Ligata, Haris M.S., Department of Mechanical Engineering Supervisor: Prof. Dr. Ömer Gündüz Bilir Co-supervisor: Assoc. Prof. Dr. Levend Parnas April 2000, 123 pages The aim of this study was investigation of the influence of fillers on the mechanical properties of fiber reinforced polymer matrix composites. The mechanical properties of interest in this work were tension and bending strength, impact resistance and bending (flexural) modulus. For this reason, tension, bending and impact tests were performed. Influence of filler was investigated by observing the mechanical characteristics of two different systems: matrix reinforced with filler only and fiber reinforced matrix with filler. Three different kinds of filler: Ti02, AI2O3 and CaC03, were used in“as received”form. The data obtained had shown that the addition of filler resulted in an initial increase, followed by decrease in tension and bending strength. IllThe initial increase was, probably, the result of crack pinning and branching, due to inclusion of particles. Bending modulus was observed to be increasing for both systems (particulate and hybrid composites), which is expected as the matrix becomes more rigid. A decrease in impact resistance with increase in weight (or volume) fraction of filler was evident for both systems. The reason for this can be found in stress concentration which increases with the addition of weight fraction of filler. The behavior of particulate and hybrid composites was approximated by using appropriate expressions found in literature. The behavior of particulate composites could be approximated by using theoretical expressions (e.g. power law), but the behavior of hybrid composites was considerably different from the case where the appropriate expressions (e.g. law-of-hybrids) were used. The effects like crack pinning and branching, which could not be taken into consideration by these expressions, were the probable reason for the difference between the theoretical and experimental results.
Benzer Tezler
- Epoksi matris E-camı dokuma fiber takviyeli termoset kompozitlerde üçüncü bileşen kalsit dolgunun özelliklere etkisi
The effect of third component calcite filler on properties of epoxy matri̇x E-glass woven fabri̇c rei̇nforced thermoset composites
CEVRİYE İLKAY ÜN
Yüksek Lisans
Türkçe
2015
Makine MühendisliğiYıldız Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. AHMET ÜNAL
- Investigation of mechanical properties of unsaturated polyester – glass fiber composites used for boat structure
Başlık çevirisi yok
ANMAR ABDULAZEEZ OWAID
Yüksek Lisans
İngilizce
2021
Makine MühendisliğiAltınbaş ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ HAKAN KAYGUSUZ
- Boraksın biotabanlı polimerik kompozitler üzerindeki termal ve mekanik özelliklerinin araştırılması
Investigation of the thermal and mechanical properties of borax on bio based polymeric composites
SELEN YAKAR
Yüksek Lisans
Türkçe
2019
Kimya MühendisliğiHitit ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ İBRAHİM BİLİCİ
- TiO2 dolgulu cam ve karbon elyaf takviyeli kompozitlerin mekanik özelliklerinin ve kriyojenik kesici takımlar ile frezelenmesinin araştırılması
Investigation of mechanical properties of TiO2 filled glass and carbon fiber reinforced composites and their milling with cryogenic cutting tools
MUHAMMED TAKA
Yüksek Lisans
Türkçe
2025
Makine MühendisliğiBatman ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. HÜSEYİN GÜRBÜZ
- Talk cevheri katkılı beyaz çimento tabanlı harçlara mikro lif etkisinin incelenmesi
Investigation of micro fiber effect on white cement based mortars with talc ore additives
EYLÜL DENİZ ACAR
Yüksek Lisans
Türkçe
2026
İnşaat MühendisliğiBalıkesir Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. ARIN YILMAZ
DOÇ. DR. YURDAKUL AYGÖRMEZ