Bir buhar çevriminde termokompresör uygulaması ve kondenstoplu sistem ile karşılaştırılması
Application of thermocompressor in a steam cycle and comparison with steam trap system
- Tez No: 937970
- Danışmanlar: DR. ÖĞR. ÜYESİ HAVVA CEYLAN
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2025
- Dil: Türkçe
- Üniversite: Tekirdağ Namık Kemal Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Endüstriyel sektörlerde önemli bir gider kalemi olan enerji harcamaları, işletmelerin rekabet gücünü arttırmak için düşürmeleri gereken bir maliyet kalemidir. Geleneksel (kondenstoplu) buhar çevrim sistemindeki kondenstoplardan kaynaklı flaş buhar atığı bu maliyeti arttıran bir faktördür. Bu tez çalışmasında mukavva karton üretim prosesinde enerji tasarrufu sağlanması hedefi ile kondenstoplu çalışan buhar sistemini termokompresörlü bir yapıya dönüştürerek deneysel ve teorik bir çalışma yapılmıştır. Her iki sistem aynı kapasite ve aynı kâğıt kalitesinin elde edildiği şartlar altında çalıştırılarak enerji ve ekonomik açıdan karşılaştırılmıştır. Termodinamik analiz için gerekli sistem özellikleri tesisat üzerine yerleştirilmiş ölçüm elemanlarından elde edilmiştir. Termokompresörlü sistemde kurutma silindirlerinde yoğuşan suyun daha kolay tahliyesi ile ısı transferi verimi artmış bunun sonucunda da daha düşük proses basıncında çalışılabileceği görülerek optimum çalışma basıncı belirlenmiştir. Termokompresörlü sistemde yakıt tüketiminin teorik analiz sonucuna göre %30, işletmeden alınan değerlere göre %20 oranında düştüğü belirlenmiştir. Yakıt tüketimindeki azalma için ana unsur kondenstopların kaldırılması ile flaş buhar kaybının önlenmesidir. Çalışmada yakıt tüketiminin yanında su tüketimi, kimyasal tüketimi, pompa enerji tüketimindeki azalmalar da hesaplanmıştır. Termokompresör ilavesi ile sistem revizyonunun geri dönüş süresi 14 ay olarak belirlenmiştir. Elde edilen sonuçların buhar sistemlerinde termokompresör kullanımının yaygınlaştırılması için teşvik edici olduğu kanaatine varılmıştır.
Özet (Çeviri)
Energy expenditures, which are an important cost item in industrial sectors, are a cost item that businesses need to reduce in order to increase their competitiveness. Flash steam waste originating from steam traps in traditional (steam trap) steam cycle systems is a factor that increases this cost. In this thesis study, an experimental and theoretical study was conducted by converting the steam system operating with steam traps to a thermocompressor structure with the aim of saving energy in the cardboard production process. Both systems were compared in terms of energy and economy by operating under the same capacity and the same paper quality. The system features required for thermodynamic analysis were obtained from the measurement elements placed on the installation. In the thermocompressor system, the heat transfer efficiency increased with the easier discharge of condensed water in the drying cylinders, and as a result, it was seen that it could be operated at lower process pressure, and the optimum operating pressure was determined. It was determined that fuel consumption in the thermocompressor system decreased by 30% according to the theoretical analysis result and by 20% according to the values obtained from the business. The main element for the decrease in fuel consumption is the removal of steam traps and the prevention of flash steam loss. In the study, in addition to fuel consumption, water consumption, chemical consumption, and pump energy consumption reductions were also calculated. The payback period for the system revision with the addition of a thermocompressor was determined as 14 months. It was concluded that the results obtained were encouraging for the widespread use of thermocompressors in steam systems.
Benzer Tezler
- Design, optimization and testing of micro-evaporator and micro-condenser components used in a miniature vapor compression refrigeration cycle
Minyatür bir buhar sıkıştırmalı soğutma çevriminde kullanılan mikro-evaporatör ve mikro kondenser bileşenlerinin tasarım, optimizasyon ve testleri
GÖKER TÜRKAKAR
Doktora
İngilizce
2016
EnerjiOrta Doğu Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. HANİFE TUBA OKUTUCU ÖZYURT
- Numerical and experimental investigation of ejector use as the expander in the vapor-compression refrigeration cycle operating with a new generation refrigerant
Yeni nesil bir soğutucu akışkanla çalışan buhar sıkıştırmalı soğutma çevriminde genleştirici olarak ejektör kullanımının sayısal ve deneysel olarak incelenmesi
AYŞE UĞURCAN ATMACA
Doktora
İngilizce
2020
Makine MühendisliğiDokuz Eylül ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. AYTUNÇ EREK
- Buhar sıkıştırmalı soğutma çevriminde ejektör kullanımının performansa etkisi
Effects of the ejector on vapour compression cooling system
MİTHAT YAKIN
Yüksek Lisans
Türkçe
2007
Teknik EğitimZonguldak Karaelmas ÜniversitesiMakine Eğitimi Ana Bilim Dalı
YRD. DOÇ. DR. MEHMET ÖZKAYMAK
- Buhar sıkıştırmalı soğutma çevriminde oluşan basınç kayıplarının deneysel ve teorik analizi
Experimental and theoretical analysis of pressure drop in vapor compression refrigeration cycle
MEHMET ONUR İLHAN
Yüksek Lisans
Türkçe
2021
Makine MühendisliğiBalıkesir ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. ENVER YALÇIN
- R600A soğutkan kullanılan buhar sıkıştırmalı soğutma çevriminde diyabatik kılcal boru içerisindeki akışın modellenmesi
Modelling for refrigerant flow of R600A through diabatic cappilary tube in vapor compression system
TOLGA APAYDIN
Doktora
Türkçe
2016
Makine MühendisliğiYıldız Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. HASAN ALPAY HEPERKAN