Kompozit beton yapı elemanlarının basit eğilme etkisi altında davranışının incelenmesi
Flexural behavior investigation of composite reinforced concrete structural elements
- Tez No: 95009
- Danışmanlar: PROF. ZEKERİYA POLAT
- Tez Türü: Doktora
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2000
- Dil: Türkçe
- Üniversite: Yıldız Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 131
Özet
ÖZET Ham madde rezervlerinin kısıtlı olması, insanoğlunu, (1) Mevcut rezervleri olabildiğince ekonomik olmaya, (2) Yeni malzemeler keşfetmeye zorlamaktadır. Bu bağlamda yerel malzemelerin kullanılabilirliklerinin araştırılması, özellikle inşaat mühendisliği uygulamaları bakımından önem taşımaktadır. Yerel yapı malzemeleri rezervleri ve çeşitliliği bakımından oldukça zengin bir potansiyele ve yapı geleneklerine sahip Anadolu'da, hafif yerel tabiî agregalar kullanarak taşıyıcı ve taşıyıcı olmayan yapı elemanları üretmek ve bunların özelliklerini ve performanslarım test etmek, son zamanlarda gittikçe yaygınlaşan bir araştırma ve uygulama alanıdır. Bu çalışmada; Kayseri Develi yöresinde bol miktarda bulunan tabiî bims kumu ve agregası kullanılarak üretilen“hafif beton-beton”kompozit betonarme döşeme elemanlarının kullanılabilirliği araştırılmıştır. Bu amaçla,“120*220*h”cm. boyutunda, normal+hafif beton kalınlıkları 5+5 cm., 5+8 cm. ve 5+10 cm. olan 24 adet betonarme kompozit kesitli plak elemanlar; çekme bölgesi normal beton ve basmç bölgesi hafif beton olacak şekilde, donatı yüzdeleri ise çekme kırılması, denge kırılması ve basınç kırılması verecek şekilde boyutlandırılmak suretiyle üretilmişlerdir. Ayrıca kompozit elemanlarda rij itlik değişimini kıyaslayabilmek amacıyla, yine kalınlıkları 10 cm., 13 cm., 15 cm. olan 3 adet betonarme normal beton kesitli plak elamanlar üretilmiştir. Numuneler 1/3 noktalarından yüklenerek kırılmış ve önerilen kompozit döşeme elemanlarda sağlanan ağırlık tasarrufu ve kullanılabilirlikleri deneysel verilere dayandırılarak gösterilmiştir. Sonuç olarak; Hafif beton için 400 dozaj ile C16 kalitesinde beton imal edilirken, normal betonda 300 dozaj ile aynı beton kalitesi elde edilebilmiştir. Hafif beton ve normal betonda elastisite modülleri arasındaki oran 1/3, kompozit ve normal beton plakların eğilme rij itlikleri arasındaki oran ise 1/2 mertebelerinde bulunmuştur. Normal ve hafif beton derzinin 4-6 mm. pürüzlendirilmesinin deney sonucunda, kesit davranışı açısından yeterli olduğu tespit edilmiştir. Kompozit plak kullanımı ile yapı öz ağırlığının %20«30 daha azaldığı hesaplanmıştır. Deney sonucunda Kompozit plak elemanlarının kesme dayanımının normal beton kesitli plak elemanlara göre daha düşük olduğu gözlenmiştir. xvıı
Özet (Çeviri)
ABSTRACT Because world sources of raw materials are getting depleted continuously, mankind is forced to exploit the existing reserves as economically as possible and to explore new materials. Hence, research on usability of locally available materials, especially in civil engineering applications, has became more important in the recent years. Because of widespread volcanic formations, among other geologic peculiarities of such zones, light-weight aggregates of pumice type is found abundantly at various places of Anatolia. Recently, research on practicability of using these rich natural reserves of pumice aggregates as the major constituent of either structural or nonstructural light-weight concrete has gained momentum both in academic and industrial fields in Turkey. In this study, usability of“composite reinforced concrete”(CRC) slab units as structural elements consisting of an upper layer of light- weight concrete underlaid by a lower layer of normal-weight concrete, produced using the pumice aggregates of the Develi region, which is a district of Kayseri lying in the southern foothills of the Erciyes Mountain, is investigated. For this purpose, a total of 24 number of slab units of 120x220xh cm dimensions each are produced at varying composite depths, which had 5+5, 5+8, and 5+1 Ocm combinations, the first 5 cm being the height of the normal-weight concrete layer and the second value being the height of the lightweight concrete layer, respectively. Some of these slabs are designed and produced to be under-reinforced, some as balanced, and some others as over-reinforced. With the purpose of comparing the behavior of all these various CRC slab units versus the conventional ones, three more normal-weight reinforcete concrete (RC) slaps of 10 cm, 13 cm, and 15 cm thickness are produced using normal- weight concrete only. As a result of experiments subjecting these slabs to simple bending moments in a two-point-loading setup, it is observed that the behaviors of the CRC slab units are reasonably satisfactory with considerable savings in dead weight as compared to those of normal- weight concrete; and It is calculated that a reduction of about 20-30% in overall dead weight of a structure will result if such CRC slabs are used. In conclusion, it is experimentally determined that the ratio of elasticity modulus of the structural light-weight concrete produced with the suitably graded Develi pumice XVIIIaggregates with a cement dosage of 400 kgf/m3 to that of normal-weight concrete having a cement content of 300 kgf/m3 is about 1/3, and the ratio of flexural stiffnesses of the CRC to RC slabs is around 1/2, respectively. The shear strength of CRC units is observed to be a little less than that of RC elements. It is determined that producing protrusions of approximately 5mm heights by manual trimming of top of the lower normal-weight concrete layer in fresh form is sufficient to provide sufficient bonding between the light weight and normal-weight concrete layers. XIX
Benzer Tezler
- Improvement of the cyclic flexural capacity of RC columns with FRP reinforcement
Lifli polimer donatılar kullanılarak betonarme kolonların çevrimsel yükler altında eğilme kapasitelerinin artırılması
ENGİN CÜNEYT SEYHAN
Doktora
İngilizce
2016
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. ALPER İLKİ
- Taşıyıcı sistemi süneklik düzeyi yüksek kompozit kolonlu moment aktaran çelik çerçevelerden oluşan binalar için tasarım esaslarının değerlendirilmesi
Examination of design rules for high ductile steel buildings with composite column moment frames
BULUT ERTAŞ
Yüksek Lisans
Türkçe
2018
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. CAVİDAN YORGUN
- Betonarme yapı elemanlarının çelik lamalarla güçlendirilmesi ve birleştirilmesi; deneysel inceleme
The strengthening and joining method for structural concrete members by using plates; experimental study
MAHMUT KÖSE
- Mevcut öngermeli kirişli betonarme bir köprünün AASHTO LRFD'ye göre çelik I kirişlerle kompozit tasarımı ve karşılaştırmalı analizi
Design and comparative analysis of an existing prestressed concrete bridge with a composite steel I-girder bridge according to AASHTO LRFD specification
GİZEM KOLGU YİĞİT
Yüksek Lisans
Türkçe
2019
Mühendislik Bilimleriİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. ELİŞAN FİLİZ PİROĞLU
- Düşük dayanımlı betona sahip betonarme kolon ve birleşimlerin deprem yükleri altında davranışlarının incelenmesi ve iyileştirilmesi
The behavior of reinforced concrete columns and joints with low strength concrete under earthquake loads: An investigation and improvevement
İDRİS BEDİRHANOĞLU
Doktora
Türkçe
2009
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. ALPER İLKİ
PROF. DR. METE A. SÖZEN