Lamel grafitli dökme demirlerde silisyum'un mekanik özelliklere etkisi
Effect of silicon on the mechanical properties in the lamellar graphite cast irons
- Tez No: 98495
- Danışmanlar: PROF.DR. H. ERMAN TULGAR, PROF.DR. M. NİYAZİ ERUSLU
- Tez Türü: Yüksek Lisans
- Konular: Metalurji Mühendisliği, Metallurgical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 1999
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 88
Özet
LAMEL GRAFİTLİ DÖKME DEMİRLERDE SİLİSYUMUN MEKANİK ÖZELLİKLERE ETKİSİ ÖZET Günümüzde dökme demirler geniş kullanım alanlarıyla yaşantımızda büyük bir yer edinmişlerdir. Dökme demirlerin üstün mekanik özellikleri ve diğer önemli özelliklerinin yam sıra fiyatlarının da alternatiflerine göre düşük olması sayesinde tercih sebebi olmuşlardır. Mühendislik malzemeleri içinde lamel grafitli dökme demirlerin özel bir yeri vardır. Lamel grafitli dökme demirler, demir esaslı metaller arasında en düşük döküm ısısına sahip olmaları, dökme demirler ailesinde özel bir yerleri olmasının nedenlerinden sadece bir tanesidir. Lamel grafitli dökme demirler, bileşimlerindeki karbonun çoğunu serbest grafit lamelleri halinde içeren dökme demir tipidir. Yaklaşık %2,50'den %4,0'a kadar çıkan erimiş karbon nedeniyle lamel grafitli dökme demirler, demir esaslı metaller arasında en düşük döküm ısısına ve en az büzülmeye sahiptir. Lamel grafitli dökme demir özellikleri büyük oranda katılaşma sırasında oluşan grafit lamel tipine bağlıdır. Grafit lamel tipi ise kimyasal bileşim, soğuma hızı, kesit kalınlığı, aşılama hızı gibi faktörlerden etkilenmektedir. Bu çalışmada, lamel grafitli dökme demirlerde değişen miktarlarda silisyum elementinin etkileri incelenmiştir. Lamel grafitli dökme demirlerin analizinde silisyum elementinin miktarını değiştirmek, bunun lamel grafitli dökme demirlerin mikroyapısında ve mekaniksel özelliklerinde meydana gelen değişikliler gözlenmiştir. Döküm işlemleri îmas Sanayii Sitesi'ndeki dökümhanede, deneysel çalışmaların bir kısmı T.C. Sanayii ve Ticaret Bakanlığı'na bağlı Kosgep laboratuarlarında, diğer bir kısmı ise İ.T.Ü. Kimya-Metalurji fakültesi laboratuarlarında yapılmıştır. Döküm işlemlerinde kullanılan hematit II piki Karabük Demir Çelik Fabrikalan'ndan istihsal edilerek endüksiyon ocaklarında ergitme işlemi yapılmıştır. Bu ergitme işlemleri sırasında Silisyum elementinin değişen miktarları potada değil de bizzat endüksiyon ocağında yapılmıştır. Döküm işlemi sırasında %1,8 Si miktarı olan dökümden başlanarak sırası ile %2,0, %2,20, %2,50 ve %2,70 Si miktarları içeren dökümler endüksiyon ocağına yapılan Si ilavesiyle elde edilmişlerdir. Silisyum elementinin değişen miktarlarmdaki döküm işlemleri sırasında %C 3,62 ve %Mn 0,94 olarak sabit tutulmaya çalışılmıştır. Bu çalışmalar sırasında artan silisyum miktarı neticesinde çekme mukavemeti ve sertlik değerlerinde düşmeler, mikroyapıda ise çoğunlukla perlitikten çoğunlukla ferritiğe doğru değişmeler gözlenmiştir. vıı
Özet (Çeviri)
EFFECT OF SILICON ON THE MECHANICAL PROPERTIES IN THE LAMELLAR GRAPHITE CAST IRONS SUMMARY Today, cast irons have a wide range of use. Cast irons have good mechanical properties, they are preferred since their costs are lower than their alternatives in addion to their other important properties. Lamellar graphite cast irons have a special place in engineering materials. Having lowest casting temperature among the ferrous metals is only one of the reasons for being a special place inside the cast iron family. Lamellar graphite cast irons are a cast iron type that most of the carbon in its composition is in the form of free graphite lamels. Lamellar graphite cast irons have lowest casting temperature and minimum shrinkage amoung the ferrous metals due to the carbon content from about 2,80% to 4,0% in their compositions. Properties of the lamellar graphite cast irons depend mostly on the type of graphite lamels occuring during solidification. The type of the graphite lamels is affected by the factors such as chemical composition, cooling rate, section thickness and inoculation. In this study, the effect of Si element on the properties of lamellar graphite cast irons are investigated. Changes occuring in the microstructure and the mechanical properties by changing the content of the Si element of the lamellar graphite cast irons are observed. Casting operations were done in a foundry in the İMES industrial site, some parts of the experimental studies were done in the KOSGEB laboratories of the T.C. Ministry of Industry and Trade, and the other parts were done in the laboraties of the Chemical-Metallurgical Engineering Faculty of Istanbul Technical University. Hematite II pig used in the casting operations was produced in the KARDEMÎR iron and steel factory and remelted in an induction furnace. Changing amounts of silicon were added to the melt in the induction furnace, not in the crucible during casting operations. Starting alloy contains 1,80% Si, and castings containing 2,0% Si, 2,20% Si, 2,50% Si, and 2,70% Si were obtained by adding silicon directly to the induction furnace. During the casting of the lamellar graphite cast irons containing various amounts of Si, the amount of the carbon and manganese was tried to be held constant; C%:3,62, Mn%:0,94. During these studies, decrease in the tensile strength and hardness values, and changes in the microstructures from mostly pearlite to mostly ferrite were observed with the increasing Si content. VUl
Benzer Tezler
- Pik ve sfero dökme demirlerde SiC takviyesinin mekanik özelliklere etkisinin incelenmesi
Investigation of the SiC additives effects on mechanical properties of cast irons
ÇAĞLAR ÖNAL
Yüksek Lisans
Türkçe
2022
Metalurji MühendisliğiManisa Celal Bayar ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. OSMAN ÇULHA
- Lamel grafitli dökme demirlerin üretiminde metalurjik silisyum karbür ve ferro silisyum katkılarının malzeme üzerindeki mekanik, metalurjik ve ekonomik etkisinin araştırılması
The investigation of the mechanical, metallurgical and economic effect of metallurgical silicium carburete and ferro silicon additives on the materials of production of lamel graphite cast iron
NURETTİN BURAK ŞEN
Yüksek Lisans
Türkçe
2018
Makine MühendisliğiNecmettin Erbakan ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. HÜSEYİN ARIKAN
- Lamel grafitli dökme demirlerde termal analiz yöntemi ile karbon eşdeğerliğinin tayini, mikroyapı ve mekanik özelliklere etkisinin incelenmesi
Investigation of the effect of carbon equality on microstructure and mechanical properties with thermal analysis methods in lamel graphite cast iron
BÜNYAMİN KURT
Yüksek Lisans
Türkçe
2019
Metalurji MühendisliğiSakarya ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. AHMET ÖZEL
- Lamel grafitli (gri) dökme demirlerde dolum hızı, döküm sıcaklığı ve metalürji kalitesinin farklı kesit kalınlıklarında akıcılık özelliklerine etkisinin incelenmesi
Investigation of the effects of filling speed, casting temperature and metallurgical quality on fluidity properties at different section thicknesses in lamel graphite (gray) cast iron casting
SAMİ KÖSE
Yüksek Lisans
Türkçe
2022
Makine MühendisliğiGümüşhane ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. EBRU EMİNE ŞÜKÜROĞLU
- Lamel grafitli ve küresel grafitli dökme demirlerde karbon eşdeğerinin mekanik özellikler ve mikroyapıya etkisinin incelenmesi
Examining the affect of carbon equivalent to the mechanic properties and micro structure in flake graphite cast iron and spheroidal graphite cast iron
LEVENT CENK KUMRUOĞLU
Yüksek Lisans
Türkçe
2003
Metalurji MühendisliğiSakarya ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. AHMET ÖZEL