Geri Dön

17-4PH çökelme sertleştirmeli paslanmaz çelik kuvvet dönüştürücü yay elemanlarının iç yapısal özelliklerinin performans üzerine etkilerinin araştırılması

An investigation on the effect to the performance of the microstructural characteristics of 17-4PH precipitation-hardened stainless steel force transducers

  1. Tez No: 136660
  2. Yazar: BÜLENT AYDEMİR
  3. Danışmanlar: PROF. DR. ERDİNÇ KALUÇ
  4. Tez Türü: Doktora
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: 17-4 PH, Çökelme Sertleştirmeli Paslanmaz Çelik, Kuvvet Dönüştürücü, Histerisiz Hatası, Sürünme Hatası, 17-4 PH, Precipitation Hardened Stainless Steel, Force Transducer, Hysteresis Error, Creep Error
  7. Yıl: 2003
  8. Dil: Türkçe
  9. Üniversite: Eskişehir Osmangazi Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Konstrüksiyon ve İmalat Bilim Dalı
  13. Sayfa Sayısı: 206

Özet

Direnç uzama ölçerli kuvvet dönüştürücüler, kuvvet altında elastik olarak deformasyona uğrayarak, gösterge cihazında elektriksel olarak doğrusal bir değişim gösteren ölçüm cihazlarıdır. Genel olarak yapılan; yay malzemesi, dirençli uzama ölçer ve gösterge ünitesinden oluşur. Yay malzemesi ve iç yapısal özellikleri, kuvvet dönüştürücü performans özellikleri olarak nitelendirilen tekrarlanabilirlik, doğrusallık, histerisiz ve sürünme hataları üzerinde en etkili elemandır. Bu amaçla, yay malzemesi olarak 17-4PH çökelme sertleştirmeli paslanmaz çelik seçilmiş ve uygulanan ısıl işlemlerle iç yapısı değiştirilerek, kuvvet dönüştürücü performansına olan etkisi araştırılmıştır. Kuvvet dönüştürücüler, 100 kN kapasiteli, çekme yönünde ölçüm yapacak ve kolon türü olarak tasarlanmıştır. Yay malzemesi 17-4PH paslanmaz çeliğin iç yapısal özelliklerini değiştirmek için literatürde yer alan H900, H925, H1025, H1150 ısıl işlemleri ve özel olarak belirlenen H450, G450, Y450, S450 ısıl işlemleri numunelere uygulanmıştır. Elde edilen iç yapılar farklı yöntemlerle (optik mikroskop, SEM, TEM, X-ışım taraması) gözlenmiş ve numunelerin performans özelliklerinde görülen farklılıklar belirlenmiştir. Bu çalışmanın sonucunda, öncelikle tekrarlanabilirlik ve doğrusallık hataları üzerinde ısıl işlemin etkin bir parametre olmadığı, bunun dışında diğer etkenler diyebileceğimiz (yapıştırma, yükleme koşullan vb.) nedenlere bağlı olduklan belirlenmiştir. Ek olarak, farklı ısıl işlemli numunelerde histerisiz ve sürünme hatasının genel olarak, sertlik değerinin artması ile giderek azaldığı tespit edilmiştir. En düşük histerisiz hatası S450 ve en düşük sürünme hatası değeri de Y450 ısıl işlemli numunede elde edilmiştir. Aynca, yay malzemesi yapısındaki dislokasyon yoğunluğunun histerisiz hatası üzerinde; atomsal yayınmanın da sürünme hatası üzerinde etkin olduğu belirlenmiştir.

Özet (Çeviri)

Force transducers with strain gage are measurement devices indicated electrical lineer variation of which are deformed elastically under the influence of force. Usually, they consist of spring material, strain gage and indicator. The microstructural properties of spring material on the performance characteristics of force transducers, such as repeatability, linearity, hysteresis, and creep errors are effective. 17-4PH precipitation hardened stainless steel was selected as a test material and heat treatments were applied in order to produce microstructural changes and effects of microstructural properties on the performance of force transducer were investigated. Force transducers were designed for the capacity of lOOkN, in tension mode only and the column type. For change of microstructural properties of 17-4PH stainless steel spring material, heat treatment definitions are given as H900, H925, HI 025, HI 150 in literature and the special H450, G450, Y450, S450 heat treatments were applied to the specimens. The results of microstructural were taken by different methods such as optical microscopy, SEM, TEM, X-ray. The differences on performance properties of specimens were determined. As a result of this study, repeatability and linearity are not influenced from the microstructural properties of spring material. In addition, hysteresis and creep errors decrease with increasing hardness. Minimum hysteresis error was obtained in S450 specimen and minimum creep error was obtained in Y450 specimen. Any treatment causing an increase in dislocation density results decrease in hysteresis error. Atomic and vacancy diffusion is the most important mechanism in the formation of creep error.

Benzer Tezler

  1. Termomekaniksel işlemin 17-4 ph paslanmaz çeliğin işlenebilirliğine etkisi

    The effect of thermo mechanical processing on the machinability of 17-4 ph stainless

    AHMET AK

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiKarabük Üniversitesi

    İmalat Mühendisliği Ana Bilim Dalı

    PROF. DR. HALİL DEMİR

    DR. İSMAİL TEKAÜT

  2. Plazma nitrürlenmiş 17-4 PH paslanmaz çeliğin mekanik ve korozyon özelliklerinin incelenmesi

    Investigation of mechanical and corrosion properties of plasma nitrided 17-4 PH stainless steel

    GÖZDE RABİA AKTAŞ

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Makine MühendisliğiBursa Uludağ Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. ALİ BAYRAM

  3. 17-4 PH paslanmaz çeliği için seçilen yaşlandırma zaman ve sıcaklık parametrelerinin mekanik ve korozyon özellikleri üzerindeki etkileri

    Effects of selected aging time and temperature parameters on mechanical and corrosion properties of 17-4 PH stainless steel

    ŞÜHEDA KARALİ

    Yüksek Lisans

    Türkçe

    Türkçe

    2024

    Makine MühendisliğiHaliç Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. BEHİYE YÜKSEL

  4. Toz metalurjisi yöntemiyle elde edilen gözenekli martensitik paslanmaz çeliğin mikroyapısı ve mekanik özellikleri

    Microstructural and mechanical properties of porous martensitic stainless steel obtained by powder metallurgy method

    İLVEN MUTLU

    Doktora

    Türkçe

    Türkçe

    2011

    Metalurji Mühendisliğiİstanbul Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. ENVER OKTAY

  5. Toz enjeksiyon kalıplama metoduyla üretilmiş 17-4PH paslanmaz çelik parçalara yapılan iki tip bor ilavesinin mikroyapı ve mekanik özelliklere etkisi

    The Effect of two types of added boron on the microstructure and mechanical properties of 17-4PH stainless steel parts produced by powder injection molding

    ÖZKAN GÜLSOY

    Doktora

    Türkçe

    Türkçe

    2003

    Metalurji MühendisliğiMarmara Üniversitesi

    Metal Eğitimi Ana Bilim Dalı

    PROF. DR. SERDAR SALMAN

    DOÇ. DR. SUNULLAH ÖZBEK