Geri Dön

Adi sünger kullanılarak Al2O3 esaslı seramik filtre üretimi ve karekterizasyonu

Production and characterization of alumina based ceramic filter by using conventional sponges

  1. Tez No: 150798
  2. Yazar: İSMAİL YILDIZ
  3. Danışmanlar: Y.DOÇ.DR. AYHAN EROL
  4. Tez Türü: Yüksek Lisans
  5. Konular: Metalurji Mühendisliği, Teknik Eğitim, Metallurgical Engineering, Technical Education
  6. Anahtar Kelimeler: Seramik Filtre, sünger, sinterleme, numune, Ceramic filter, sponge, cinterleme (firing), sample (consist)
  7. Yıl: 2004
  8. Dil: Türkçe
  9. Üniversite: Afyon Kocatepe Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Metal Eğitimi Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 89

Özet

Seramik filtre üretime bakıldığında genellikle yurtdışından getirilen özel süngerler kullamlmaktadır. Uygun özelliklere sahip değişik hammadde ve malzemeler kullanılarak hazırlanan çamura bu özel süngerler emdirilmiş ve değişik sıcaklıklarda pişirilerek filtre üretimi gerçekleştirilmiştir. Bu çalışmada ekonomik olması nedeniyle özel süngerler yerine günlük hayatta sıkça kullanılan kapı-pencere izolasyon süngeri tercih edilmiştir. Başta alümina seramik malzemesi kullanılmak üzere üç farklı grupta değişik reçeteler hazırlanmıştır. 1. grup deney numuneleri alümina-polivinil alkol 2. grup deney numuneleri alümina-mangan oksit ve 3. grup deney numuneleri ise alümina ve bentonit hammaddelerinden elde edilmiştir. Üç farkılı grupta hazırlanan çamura daldırılan sünger etüvde kurutulduktan sonra, farklı sinterleme sıcaklıklarında pişirilmiştir. Pişirilme sonrası elde edilen filtreler, SEM, EDX gibi metalografik analizlerin yam sıra birim hacim ağırlık, boyca küçülme, su emme analiz, gözeneklilik ve korozyon testi gibi fiziksel testlere tabi tutulmuştur. Deneysel çalışmalar sonucunda, adi süngerin filtre üretiminde kullanılmasında iyi bir tercih olmadığı, 1. ve 3. grup deney numuneleri 1550 °C sıcaklığına kadar özelliklerini korurken, 2. deney grubunun 1450“C'de yapısının bozulduğu gözlenmiştir. Numunelere uygulanan tüm test ve analiz sonuçları değerlendirildiğinde, bentonit katkısı ile hazırlanan ve 1550 ”C'de sinterlenen 3. grup deney numunelerinin diğer grup numunelerine göre seramik filtre kullammı için daha uygun özelliklere sahip olduğu sonucuna varılmıştır.

Özet (Çeviri)

Generally, special sponges which are imported from other countries are used for production of ceramic filter. These sponges are dipped into slurry then the sponges are fired in a furnace. Because of firing, the sponges evaporate and only filters remain. In this study, instead of these special sponges, sponges used for insulation of windows and doors are used. Three different types of recipes were prepared for slurry. The first recipe consists of alumina and polivinil alcohol, the second recipe consists of alumina and manganese oxide and the third recipe consists of alumina and bentonite. After dipping sponges into these three types of mixtures, the sponges were dried in an oven. Then they are fired in a furnace at different temperatures. Filters were analyzed with SEM and EDX. Also, porosity, corrosion, water absorbsion tests were performed and density and shrinkage were determined for each filter. Experimental studies showed that insulation sponges are not suitable for this application. Also, it was observed that the filter material obtained from the first and the third recipes are stable at and below the firing temperatures of 1550 °C. However, the filter material obtained from the second recipe is not stable at and above 1450 °C. When the properties of all of the filter materials were considered, it was seen that the filter material obtained from the third recipe and fired at 1550 "C has the best properties.

Benzer Tezler

  1. Döner fırında katı esaslı redükleyici kullanılarak sünger demir üretimi

    Spange iron production in the rotary tube furnace by using solid reductant

    NAZIM NARÇİN

    Yüksek Lisans

    Türkçe

    Türkçe

    1990

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Y.DOÇ.DR. SÜHEYLA AYDIN

  2. Enhancement of ımplantation potential of mouse blastocysts via use of three-dimensional endometrial co-cultures on natural and artificial materials

    Fare embriyosunun implantasyon potansiyelinin doğal ve yapay materyaller üzerinde 3 boyutlu endometriyal ko-kültür kullanılarak artırılması

    YAĞMUR ERGÜN

    Yüksek Lisans

    İngilizce

    İngilizce

    2020

    Histoloji ve EmbriyolojiKoç Üniversitesi

    Üreme Biyolojisi Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ SERÇİN KARAHÜSEYİNOĞLU

  3. Design and characterization of a wound dressing system for effective pain relief

    Ağrı kesici salımı yapan yara örtüleri hazırlanması ve karakterizasyonu

    BEREN ŞEN

    Yüksek Lisans

    İngilizce

    İngilizce

    2016

    Biyoteknolojiİstanbul Teknik Üniversitesi

    Moleküler Biyoloji-Genetik ve Biyoteknoloji Ana Bilim Dalı

    DOÇ. DR. FATMA NEŞE KÖK

  4. 3 boyutlu baskı yönteminde kullanılabilecek sol-gel methodu ile sentezlenen biyoaktif cam doku iskelesi geliştirilmesi ve karakterizasyonu

    Development and characterization of 3D-printed bioactive glass tissue scaffold synthesized using the sol-gel method

    YİĞİT TURAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Metalurji MühendisliğiMarmara Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ SONGÜL ULAĞ

    PROF. DR. OĞUZHAN GÜNDÜZ

  5. Development and characterization investigations of mechanically alloyed and activated sintered W-1WT% Ni matrix composites reinforced with TiB2 and La2O3 particles

    TiB2 ve La2O3 partikülleri ile güçlendirilmiş W ?%1 Ni (ağırlıkça) matriksli kompozitlerin mekanik alaşımlama ve aktive edilmiş sinterleme yöntemleriyle üretilmesi ve karakterizasyonu

    ÖMER UTKU DEMİRKAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2011

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    İleri Teknolojiler Ana Bilim Dalı

    PROF. DR. MUSTAFA LÜTFİ ÖVEÇOĞLU