Geri Dön

Yüzey akustik dalga esasına dayanan filtre ve rezonatörlerin analizi ve tasarımı

Analysis and design of surface acoustic wave filters and resonators

  1. Tez No: 22068
  2. Yazar: ŞENAY CÖMERT
  3. Danışmanlar: PROF. DR. ERGÜL AKÇAKAYA
  4. Tez Türü: Yüksek Lisans
  5. Konular: Elektrik ve Elektronik Mühendisliği, Electrical and Electronics Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 1992
  8. Dil: Türkçe
  9. Üniversite: İstanbul Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Belirtilmemiş.
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 130

Özet

electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXID

Özet (Çeviri)

The applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXIDThe applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXIDThe applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)electrode position and the apodisation function required to reproduce a desired waveform. This procedure is applicable to the design of weighted dispersive filters. Surface wave techniques can be used to produce several types of stable oscillator using SAW resonator. The resonator is basically two reflectors forming a surface wave cavity and a transducer which are used to generate a surface wave packet on the surface. The reflectors are periodic arrays of either metal strips or grooves and reflect when their period is equal to half the SAW wavelength and there is corresponding increase in the array transmission loss. With a large number of strips or grooves, the array reflection coefficient can be very close to unity. For YZCY-cut Z-propagatingD lithium niobate which has an impedance discontinuity of 1.2%, 300 metallic strips are required in the array for a reflection coefficient of 98%. The resonator can give very high Q factors, up to 20,000, giving good stability. Furthermore, highly stable c. w. sources with frequencies up to about 2 GHz can be obtained by using SAW resonators. In this thesis, it will be given an analysis and synthesis procedure using transmission line model for the reflectors. The basic resonator structure is illustrated in Figure 3. Grooved array reflector substrate Figure 3. Two-port surface acoustic wave resonator CXIDThe applicability of surface wave devices to practical electronic systems is basically determined by the centre frequencies, bandwidths and delays obtainable. The upper limit for the centre frequency is determined by fabrication techniques, and current lithography is about 1.5 GHz. At low frequencies SAW devices become more bulky and expensive and other technologies become more suitable, for example bulk acoustic wave resonators for bandpass filters or digital techniques for signal processing. Consequent 1 y-, SAW devices are not normally used below a few MHz. In most applications this frequency range implies that the devices are used in the I. F. section of ' the system and this has the important consequence that low insertion loss is not generally a priority. For example, bandpass filters have typically 15 to 30 dB loss, and this is acceptable for many applications. Bandwidths generally range from a minimum of about lOO kHz to a maximum of about 50% of the centre frequency. CXIIZ)

Benzer Tezler

  1. Tez No

    166524

    Yüzey akustik dalga filtrelerinin haberleşme sistemlerindeki uygulamaları

    Surface acoustic wave filter applications in communication systems

    HASAN KARTLAK

    Yüksek Lisans

    Türkçe

    Türkçe

    2005

    Elektrik ve Elektronik Mühendisliğiİstanbul Teknik Üniversitesi

    Elektronik ve Haberleşme Mühendisliği Ana Bilim Dalı

    DOÇ. DR. MÜRVET KIRCI ÜÇER

  2. Tez No

    66494

    Akustik yüzey dalga esasına dayanan filtrlerin analizi, tasarımı ve GSM sistemindeki uygulamaları

    Analysis and design of saw filter and saw filter applications in GSM

    H.CEMİL KARAGÜZEL

    Yüksek Lisans

    Türkçe

    Türkçe

    1997

    Elektrik ve Elektronik Mühendisliğiİstanbul Teknik Üniversitesi

    Elektronik ve Haberleşme Mühendisliği Ana Bilim Dalı

    PROF. DR. ERGÜL AKÇAKAYA

  3. Tez No

    142597

    Yeni Cami'nin akustik açıdan performans değerlendirmesi

    Evaluation of the acoustical performance of the New Mosque

    EVREN YILDIRIM

    Yüksek Lisans

    Türkçe

    Türkçe

    2003

    Mimarlıkİstanbul Teknik Üniversitesi

    Mimarlık Ana Bilim Dalı

    PROF. DR. SEVTAP YILMAZ DEMİRKALE

  4. Tez No

    192306

    Mobil telefon kullanımına bağlı oluşan 900-1800 mhz radyo frekans dalgalarının meydana getirdiği elektromanyetik alanın iliak kanat kemik mineral yoğunluğuna etkisi

    The effect of electromagnetic fields on bone mineral density of iliac bone produced by 900-1800 mhz radio frequency waves dependent on cellular phone usage

    BEŞİR ANDAÇ AKSOY

    Tıpta Uzmanlık

    Türkçe

    Türkçe

    2006

    Ortopedi ve TravmatolojiSüleyman Demirel Üniversitesi

    Ortopedi ve Travmatoloji Ana Bilim Dalı

    PROF.DR. NEVRES HÜRRİYET AYDOĞAN

  5. Tez No

    496339

    Frequency-selective remote actuation via continuous beam spans

    Sürekli kiriş dizileri yardımıyla frekans-seçici uzaktan tahrik

    JABER SALAMAT

    Yüksek Lisans

    İngilizce

    İngilizce

    2016

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. ERDAL BULĞAN

Geri Dön