Geri Dön

The effect of boron nitride and boron carbide additives on the properties of mesophase pitch based carbon foam

Bor nitrür ve bor karbür katkı malzemelerinin mezofaz zift bazlı karbon köpüğünün özelliklerine etkisinin incelenmesi

  1. Tez No: 223636
  2. Yazar: SENA EFE
  3. Danışmanlar: PROF.DR. EKREM EKİNCİ
  4. Tez Türü: Yüksek Lisans
  5. Konular: Kimya Mühendisliği, Chemical Engineering
  6. Anahtar Kelimeler: Karbon köpük, Mezofaz zift, Bor nitrür, Bor karbür
  7. Yıl: 2006
  8. Dil: İngilizce
  9. Üniversite: İstanbul Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Kimya Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 77

Özet

Karbon köpügü yeni ve ileri karbon malzemelere önemli bir örnektir ve düsük yogunluk, yüksek ısıl iletkenlik, gözenekli yapı ve dayanıklılık en önemli özellikleridir. Karbon köpügü ısıyı bakırdan altı, aluminyumdan ise dört kat daha fazla iletebilmektedir. Bir çok endüstri karbon köpügünü özelliklerine baglı olarak kendi amaçları dogrultusunda kullanabilir. Örnegin, karbon köpügü yüksek ısıl iletkenliginden dolayı bilgisayar islemcilerinde heat sink olarak, düsük yogunlugundan dolayı hafif malzemelerde kullanılnamktadır. Karbon köpügü ayrıca disçilikte ve kemiklerde de kullanılmaktadır. Yapılan bu çalısmada, Mezofaz zift bazlı karbon köpügünün üretilmesinde uygulanan proses söyledir; mezofaz zift alüminyum mold içinde ve otoklava yerlestirilir. Burada erime noktasının üzerine kadar ısıtılır, sisteme basınç verilir. Basıncın hızlıca bosaltılmasından sonra, stabilizasyon ve karbonizasyon islemleri ile karbon köpügü ele geçirilir. Bu yöntemle elde edilen karbon köpügü stereo mikroskop, Taramalı elektron mikroskop, cıva porozimetre ve sıkıstırılabilirlik testi ile karakterize edilir. Üretilen karbon köpüklerinin yogunlukları ölçülmüstür. Karakterizasyon sonuçlarına göre ise degisik proses sartlarında üretilen karbon köpügünün yapısı belirlenmis olur. Bu çalısmada degisik sıcaklıklar, bor nitrür ve bor karbür katkı malzemeleri, farklı yumusama noktalarına sahip ziftlerin kullanılması ile karbon köpügü üretimi deneyleri gerçeklestirilmistir. Yapılan deneylerin sonucunda, artan sıcaklıkla daha homojen, yogun, dayanıklı ve gözenekli karbon köpügü elde edilmistir.

Özet (Çeviri)

Carbon foam is important example of the new and advance carbon materials, which has low density, high compressive strength, high porosity and high thermal conductivity. The thermal conductivity of carbon foam is six times higher than copper and four times higher than aluminium. Potential application area of carbon foam is huge; many industries used carbon foam for different purposes related to its properties and characterisation. For example due to its high thermal conductivity carbon foam used as a heat sink in a computer precursors, or its used in light weight antennas because of its low density, carbon foam even found application in bone surgery and dentistry. In this study, mesophase pitch based carbon foam is produced. In the production pitch is introduced in an autoclave. The autoclave is heated above the melting temperature of the pitch. The autoclave is pressurize, then depressurized rapidly. Later, stabilization and carbonization step leads to obtain carbon foam. Carbon foam produced with this technique was characterized with stereomicroscopy, scanning electron microscopy (SEM), mercury Porosimetry, and compressive testing. Also density of the samples was measured. The structures and properties of the produced carbon foams are investigated with respect to the parameters involved and further using the characterization results. The parameters, investigated are the effect of boron nitride and boron carbide additives, production at different temperatures and production of the foam with different kinds of pitches having different softening point values. As a result of these experiments it is found that; more homogenoes, interconnected, better structured, higher density, higher compressive strentgh and higher porosity carbon foams are derived with increase in temperature

Benzer Tezler

  1. Kendiliğinden ilerleyen yüksek sıcaklık sentezi yöntemi ile B4C üretiminde katalizörlerin etkilerinin araştırılması

    The investigation of effects of catalysts on the production of B4C via self propagating high temperature synthesis

    HASAN ÖZER

    Yüksek Lisans

    Türkçe

    Türkçe

    2014

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. ONURALP YÜCEL

  2. Farklı katkı malzemelerin çift bazlı sevk barutlarının özelliklerine etkisinin araştırılması

    Investigation of the effect of different additives on properties of the double based propellant

    İSLAMİ ORUÇ

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    Savunma ve Savunma TeknolojileriKırıkkale Üniversitesi

    Savunma Teknolojileri Ana Bilim Dalı

    DOÇ. DR. AYŞEGÜL ÜLKÜ METİN

  3. Grafen ve bor nitrür katkılarının titanyum diborür – titanyum karbür kompozitlerinin özellikleri üzerine etkilerinin incelenmesi

    Investigation of the effects of graphene and boron nitride additives on the properties of titanium diboride – titanium carbide composites

    BESTE ECEM KAYAR

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı

    DOÇ. DR. İPEK AKIN KARADAYI

  4. Production and characterization of spark plasma sintered boron carbide ceramic composites suitable for ballistic use

    Balistik kullanıma uygun bor karbür seramik kompozitlerinin spark plazma sinterleme yöntemi ile üretimi ve karakterizasyonu

    BURCU APAK GÜLSEVER

    Doktora

    Türkçe

    Türkçe

    2018

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. FİLİZ ŞAHİN

  5. B4C esaslı kompozitlerin B4C/Me başlangıç tozlarından hareketle spark plazma sinterleme (SPS) yöntemi ile üretilmesi ve karakterizasyonu

    Production and characterization of B4C based composites from B4C/Me starting powders by using spark plasma sintering (SPS) method

    MERAL CENGİZ

    Doktora

    Türkçe

    Türkçe

    2016

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı

    PROF. DR. FİLİZ ŞAHİN