Geri Dön

Isı pompalı kurutma sistemlerinde soğutkanların performansa etkisinin sayısal incelemesi

Numerical investigation of refrigerants' effects on performance in heat pump drying systems

  1. Tez No: 329588
  2. Yazar: SERKAN ERDEM
  3. Danışmanlar: PROF. DR. HASAN ALPAY HEPERKAN, DOÇ. DR. DERYA BURCU ÖZKAN
  4. Tez Türü: Doktora
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2013
  8. Dil: Türkçe
  9. Üniversite: Yıldız Teknik Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Isı Proses Bilim Dalı
  13. Sayfa Sayısı: 135

Özet

Küresel ısınma, ozon tabakasının incelmesi ve enerjinin yüksek maliyeti uzun zamandır dikkatleri çevre dostu ve yüksek enerji verimli sistemler üzerine çekmiştir. Çevresel etkileri sebebiyle kullanılabilecek soğutkanlar da çeşitli protokollerle sınırlandırılmıştır. Çeşitli ısıtma?soğutma sistemlerinde kullanılan soğutkanlar yerlerini yenilerine bırakmaktadır. Bu aşamada, CO2 doğal olmasından ötürü çevreye zararının olmaması, maliyetinin düşük olması ve kolay temin edilebilmesi sebebiyle ön plana çıkmaktadır. Isı pompalı çamaşır kurutucularında genel olarak R134a soğutkanı kullanılmaktadır ve Kyoto Protokolü ile kullanımı ciddi anlamda sınırlandırılmıştır. CO2 termofiziksel etkileri sebebiyle kurutucu işletme şartlarında çalışabilmek için çok uygun gözükmektedir. CO2?in kurutucularda kullanımı ile hem çevreye verilen zarar asgari seviyeye indirilmekte, hem de sistemin performansı arttırılmaktadır. Bu çalışmada CO2 kullanan ve transkritik çevrime göre çalışan ısı pompalı çamaşır kurutma makinesi sistemleri teorik olarak incelenmiştir. Ardından, CO2 ile çalışan ısı pompalı çamaşır kurutucu modeli geliştirilmiştir. Bir arayüz oluşturularak model, MATLAB altında çalışan bir yazılım haline getirilmiştir. Tez çalışması altı ana bölümden oluşmaktadır. Birinci bölümde öncelikle konu ile ilgili literatürde yapılmış çalışmaların bir özeti verilmiştir. Ardından tezin yapılış amacı ve ortaya konulmak istenenler belirtilmiştir. İkinci bölümde, sistemdeki ana bileşenlerin (gaz soğutucu, evaporatör, kompresör, tambur ve fan) her biri için temel kavramlar açıklanarak teorik analiz yapılmış ve hesap metodolojisi ortaya konulmuştur. Üçüncü bölümde, MATLAB R2011b programı kullanılarak, hesaplamalar bilgisayar ortamına aktarılmıştır. Bu noktada akışkan özellikleri REFPROP v7 programı kullanılarak belirlenmiştir. Evaporatörün CO2 tarafında iki fazlı akış ve ardından aşırı kızdırma bölgesinde tek fazlı akış gerçekleştiği, hava tarafında ise ısı transferi ile eş zamanlı olarak havadaki su buharının yoğuşması sebebiyle kütle transferi gerçekleştiği için, hassas bir modelin oluşturulması gerekmiştir. Bu sebeple evaporatör çeşitli sayıda segmentlere ayrılarak hesaplamalar yapılmış ve bir segmentin çıkış şartları sonraki segmentin giriş şartları olarak bilgisayara girilmiştir. Geliştirilen çözüm algoritması ile teorik analizi yapılmış olan bileşenler bir araya getirilerek ısı pompalı kurutma makinesi sisteminin genel modeli oluşturulmuştur. Son olarak da oluşturulan kullanıcı arayüzü ile model, MATLAB altında çalışan bir yazılım haline getirilmiştir. Dördüncü bölümde, literatürden derlenen deneysel verilerle sistem bileşenlerinin doğrulaması yapılmıştır. Bu kısımda gaz soğutucularda boru içerisindeki CO2 akışı için ısı taşınım katsayısı ve basınç kaybı karşılaştırmaları grafikler halinde verilmiştir. Gaz soğutucunun hava tarafında gerçekleşen ısı transferi ve basınç kaybı doğrulamaları için sırasıyla Colburn (j) ve sürtünme (f) faktörleri literatür ile karşılaştırmalı olarak verilmiştir. Ardından evaporatörde boru içerisinde gerçekleşen CO2 akışında, kuruluk derecesine bağlı olarak ısı taşınım katsayısının değişimi ve kütle akısına bağlı olarak basınç kaybının değişimi verilmiştir. Bu kısımda boru içerisinde gerçekleşen iki fazlı CO2 akışı kuruluk derecesinin değişimine bağlı olarak dokuz farklı tipte değerlendirilmiştir. Isı taşınım katsayısının değişimleri akış tiplerinin değişimleri ile beraber gösterilmiştir. Evaporatörün hava tarafında gerçekleşen ısı transferi ve basınç kaybı doğrulamaları için yine sırasıyla Colburn (j) ve sürtünme (f) faktörleri literatür ile karşılaştırmalı olarak verilmiştir. Evaporatörün hava tarafında gerçekleşen yoğuşma sebebiyle kütle transferi analizleri de literatürdeki veriler ile karşılaştırılarak kütle transferi Colburn faktörü (jm) Reynolds sayısının değişimine bağlı olarak verilmiştir. Beşinci bölümde gaz soğutucuya CO2?in giriş basıncının, evaporasyon sıcaklığının, hava debisinin, tambur veriminin, kaçak oranının, ortam havasının sıcaklığının ve bağıl neminin kurutma sistemini performansına etkileri modelden alınan sonuçlara bağlı olarak irdelenmiştir. Sistemin performansı değerlendirilirken COP, MER ve SMER değerlerinin değişimi gösterilmiştir. Buradan elde edilen sonuçlarla, kurutucunun enerji tüketimi ve kurutma süresi parametrik olarak ortaya konulmuştur. Altıncı bölümde sonuçlar ve önerilere yer verilmiştir.

Özet (Çeviri)

Global warming, ozone depletion and high cost of energy have long attracted attention to environment friendly and high energy efficient systems. Coolants which can be used due to their environmental effects have also been limited by several protocols. Coolants which are used in several heating-cooling systems have been replaced with the new ones. At this stage, CO2 comes into prominence because it does not harm the environment due to being natural and because of low cost and easy supply. Generally, R134a coolants are used in heat pump tumble dryers and its usage has been considerably limited by Kyoto Protocol. CO2 seems very suitable for working in dryer operating conditions due to its thermophysical effects. With the use of CO2 in dryers, both the harm to environment is reduced to minimum and the system performance is increased. In this study, heat pump tumble dryer machine systems which use CO2 and operate according to transcritical cycle were theoretically examined. Then, a model was developed for CO2 heat pump dryer. Model was made into a software which runs under MATLAB, by developing a graphical user interface. The thesis study consists of six main parts. The first part primarily includes a summary of the studies done in literature in relation to the matter. And then the purpose of the thesis and things to be presented are specified. In the second part, basic concepts for each main component in the system (gas cooler, evaporator, compressor, tumbler and fan) are explained and theoretical analysis is made and calculation methodology is presented. In the third part, calculations are transferred to the computer by using MATLAB R2011b program. At this point, fluid properties are determined by using REFPROP v7 program. Since two phase flow occurs in the evaporator?s CO2 side and then one phase flow occurs in the superheat area, and mass transfer occurred due to the condensation of water vapour in the air simultaneously with the heat transfer in the air part; creation of a sensitive model was required. Therefore, the evaporator was divided into a number of segments and calculations were made and the exit conditions of a segment were entered in the computer as the inlet conditions of the subsequent segment. The solution algorithm developed and the components which were theoretically analyzed were brought together and the general model of the heat pump dryer machine system was created. And finally, model was made into a software which runs under MATLAB, by developing a graphical user interface. In the fourth part, system components are validated through the empirical data which is compiled from literature. In this part, heat transfer coefficient and pressure loss comparisons for CO2 inside the tube in the gas coolers are given in graphics. For the heat transfer which occurs in the air part of the gas cooler and pressure loss validations, Colburn (j) and friction (f) factors are given respectively comparatively with literature. And then, in the CO2 flow which occurs inside the tube in the evaporator; the change in the heat transfer coefficient based on quality and the change in the pressure loss based on mass flux is given. In this part, the two phase CO2 flow which occurs inside the tube is evaluated in nine different types based on the change in quality. The changes in heat transfer coefficient are shown together with the changes in flow types. For the heat transfer which occurs in the air part of the evaporator and pressure loss validations; again respectively, Colburn (j) and friction (f) factors are given comparatively with literature. The mass transfer analyses due to the condensation which occurs in the air part of the evaporator are also given according to the change in Colburn factor (jm) Reynolds number comparatively with the literature. In the fifth part, the effects of CO2 inlet pressure to the gas cooler, evaporation temperature, air flow rate, drum efficiency, leakage ratio, temperature and relative humidity of the ambient air on the performance of the dryer system were scrutinized according to the results obtained from the model. While assessing the performance of the system, COP, MER and SMER values? variations were showed. Through the results obtained, the energy consumption and drying time of the dryer have been presented in parametrical terms. The sixth part includes results and suggestions.

Benzer Tezler

  1. Isı pompalı kurutucularda hidrokarbon gazların kullanımına geçiş sebepli yapısal tasarım çalışmaları

    Required design studies to use hydrocarbon refrigerants in heat pump dryers

    SÜLEYMAN KONAKÇI

    Yüksek Lisans

    Türkçe

    Türkçe

    2004

    Endüstri ve Endüstri MühendisliğiGebze Yüksek Teknoloji Enstitüsü

    Tasarım ve İmalat Mühendisliği Ana Bilim Dalı

    Y.DOÇ.DR. BABÜR ÖZÇELİK

  2. Isı pompalı çamaşır kurutma makinesinin sistem tasarım parametreleri optimizasyon modelinin oluşturulması

    Development of an optimization model of system design parameters of heat pump clothes dryer

    GÖKHAN SIR

    Doktora

    Türkçe

    Türkçe

    2023

    Makine MühendisliğiYıldız Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. ŞEVKET ÖZGÜR ATAYILMAZ

  3. Enerji depolama sistemli güneş enerjili gıda kurutma sistemlerinde kurutma performansının incelenmesi

    Investigation of drying performance in solar food drying systems with energy storage system

    ÖZLEM TİMURTAŞ

    Yüksek Lisans

    Türkçe

    Türkçe

    2020

    Makine MühendisliğiEge Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ GÖKHAN GÜRLEK

  4. Kanatlı borulu buharlaştırıcılarda nem alma performansının en iyileştirilmesi

    Optimizing demihumidification performance of fin and tube evaporators

    SEMİH KURULAR

    Yüksek Lisans

    Türkçe

    Türkçe

    2016

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. SEYHAN UYGUR ONBAŞIOĞLU

  5. Vision based positioning ABB IRB 140 robot for gas leakage test automation

    Gaz kaçak test otomasyonu için ABB IRB 140 robot için görüntü tabanlı pozisyonlama

    AKIN İLKER SAVRAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2018

    Bilgisayar Mühendisliği Bilimleri-Bilgisayar ve Kontrolİstanbul Teknik Üniversitesi

    Kontrol ve Otomasyon Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ TUFAN KUMBASAR