Blind shear ram blowout preventers: Estimation of shear force and optimization of ram geometry
Başlık çevirisi mevcut değil.
- Tez No: 401105
- Danışmanlar: PROF. TAYLAN ALTAN, DR. CHANGHYOK CHOI
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2010
- Dil: İngilizce
- Üniversite: The Ohio State University
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 95
Özet
Özet yok.
Özet (Çeviri)
The explosion of the Deepwater Horizon oil rig in the Gulf of Mexico showed once again that during the oil drilling operation any failures of surface equipment which is called blowout preventers (BOPs) may result in death, injury and massive oil spills that have huge impact on the environment. The blowout preventers are devices that are supposed to close off the wellbore and seal it in an emergency to prevent formation fluid from reaching the surface of the well. In a blowout preventer stack, which consists of several types of blowout preventers, the last line of defense is the blind shear ram that is supposed to close and seal the wellbore by shearing through the drill string or any other tubing when they are in the wellbore. According to a recent report prepared for the U.S. Minerals Management Services (MMS) by [Childs et al., 2004], two of the three BOP manufacturers rely on a very basic equation“the Distortion Energy Theory shear equation”to estimate the shear force requirement for shearing operation. However with recent advancement in drill pipe materials, it might not be sufficient to estimate the actual shear force to shear a specific drill pipe using yield or tensile stress by itself and the Distortion Energy Theory shear equation. Using finite element method to analyze the drill pipe materials and dimensions and simulate the entire shearing and sealing operation with blowout preventer working conditions through the finite element method can provide good approximation for actual shear force and sealing pressure to secure the well. Also, the finite element method could be used to optimize shear ram geometry so that minimum force and energy are used to shear the tube by plastic deformation. Fourteen task studies are presented throughout this research. The first two tasks were studied to develop a methodology to evaluate the required shear force to shear a certain drill pipe without considering blowout preventer working conditions effect on shearing operation. The results of these studies were compared with actual shear forces that were obtained from BOP manufacturers [Childs et al., 2004]. The next three tasks were studied to determine a relation between drill pipe diameters and shear force requirement for shearing operations. Tasks 6 to 9 were studied to evaluate the effect of the vertical load that stems from the weight of drill string on shear force requirement. The last five tasks were studied to optimize tool clearance to minimize the actual shear force. It is shown that shear forces evaluated by using finite element method (FEM-Deform 3D) simulations provided fairly accurate results for actual shear force. Also, it is found that by using FEM simulation the effect of the blowout preventer working condition on shearing operation can be estimated and ram geometries can be optimized. Therefore, FEM simulation can be used to design more reliable and efficient ram type blowout preventers.
Benzer Tezler
- Uçak yapılarının burkulması, boşlukların analizi ve bağlayıcı seçimi
Buckling of airframe structures cutout analysis and fastaner selection
BİROL UZ
Yüksek Lisans
Türkçe
1997
Uçak Mühendisliğiİstanbul Teknik ÜniversitesiUçak Mühendisliği Ana Bilim Dalı
PROF. DR. AHMET NURİ YÜKSEL
- Spastik serebral palsili hastalarda spastisitenin botulinum toksin A enjeksiyonu sonrası elastografi ile değerlendirilmesi
Evaluation of spasticity by elastography following botulinum toxin A injection in spastic cerebral palsy
HÜSEYİN BERTAN
Tıpta Uzmanlık
Türkçe
2019
Fiziksel Tıp ve RehabilitasyonSağlık Bilimleri ÜniversitesiFiziksel Tıp ve Rehabilitasyon Ana Bilim Dalı
DOÇ. DR. JÜLİDE ÖNCÜ ALPTEKİN
- İnme sonrası üst ekstremite spastisitesinde repetetif periferal manyetik stimülasyonun etkisinin makaslama akım hızı elastografi ile değerlendirilmesi: randomize kontrollü bir çalışma
Evaluation of the effect of repetitive peripheral magnetic stimulation on upper extremity spasticity after stroke using shearwave ultrasound elastography: A randomized controlled trial
SEMRA ÖZKAN
Tıpta Uzmanlık
Türkçe
2024
Fiziksel Tıp ve RehabilitasyonAnkara ÜniversitesiFiziksel Tıp ve Rehabilitasyon Ana Bilim Dalı
PROF. DR. HAYDAR GÖK
- Numerical modelling of ground motions in Eskişehir basin
Eskişehir havzasında yer hareketinin nümerik modellenmesi
LÜTFÜ İHSAN AKPUNAR
Yüksek Lisans
İngilizce
2022
Deprem MühendisliğiBoğaziçi ÜniversitesiDeprem Mühendisliği Ana Bilim Dalı
DOÇ. DR. GÜLÜM TANIRCAN
- DBYBHY 2007'ye göre tasarlanmış olan bir binanın doğrusal elastik olmayan yöntemlere göre performansının değerlendirilmesi
Performance assessment of a new building designated according to Turkish earthquake code by nonlinear elastic methods
MEŞA DEMİRBAĞ
Yüksek Lisans
Türkçe
2017
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. KONURALP GİRGİN