Takviyeli kompozit bir plakanın dinamik analizi
Dynamic analysis of a stiffened composite plate
- Tez No: 445063
- Danışmanlar: PROF. DR. VEDAT ZİYA DOĞAN
- Tez Türü: Yüksek Lisans
- Konular: Havacılık Mühendisliği, Uçak Mühendisliği, Aeronautical Engineering, Aircraft Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2016
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Uçak ve Uzay Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 85
Özet
Takviyeli kompozit plakalar, yüksek mukavemet ve göreli hafiflik özellikleri sebebiyle kullanım alanı gün geçtikçe genişleyen yapılardır. Kompozit malzeme, tanım gereği farklı özellikteki malzemeleri, istenilen mukavemet özelliklerinde oluşturmaktır. Örneğin, katmanlı kompozit plakalar için katmanların dizilişi plakanın statik ve dinamik karakteristiğini etkileyen en önemli parametredir. Bu parametreye dikkat edilerek aynı ağırlıkta olmasına rağmen statik ve dinamik olarak çok daha mukavemetli yapılar oluşturulabilir. Bu çalışmada, katmanlı kompozitler için, farklı boyutlarda ve dizilişlerde takviyesiz ve takviyeli plakalar oluşturularak statik ve dinamik analizleri ANSYS 16.2 paket programı kullanılarak gerçekleştirildi. Kalınlığı kenar uzunluklarına göre oldukça küçük olan ince plakalar kullanıldığı için analitik çözümler kayma deformasyonunu ihmal edecek şekilde klasik laminasyon teorisi kullanılarak elde edildi. Tasarım değişkenlerinin numunelerin çökme, gerilme ve doğal frekans değerlerine etkisi incelendi. Bu kapsamda çalışma takviyeli ve takviyesiz olarak iki bölümde gerçekleştirildi. İlk bölümde takviyesiz plakalar için incelemeler yapıldı. Kare bir plaka oluşturularak farklı sınır şartlarında, 15'er derecelik dizilim değişimiyle, aynı yayılı yük altında çökme ve gerilme değerlerinin değişimi incelendi. Serbest titreşim analizi yapılarak açı değişiminin mod şekilleri ve frekanslarına etkisi gözlemlendi. Ardından açıklık oranı azaltılarak bahsedilen parametrelerin farklı açıklık oranlarında değişimi incelendi. ANSYS kullanılarak gerçekleştirilen bu analizler, literatürden edinilen analitik çözümlerle kıyaslandı. İkinci bölümde ise takviyeli kompozit plakalar için incelemeler yapıldı. ½ açıklık oranında katmanlı kompozit plaka oluşturuldu. Ankastre sınır şartlarında bu plakanın ilk olarak takviyesiz analizi gerçekleştirildi. Ardından kompozit katmanlar ile oluşturulan takviye eklenerek takviye kullanımının çökme, gerilme ve doğal frekans değerlerinde meydana getirdiği değişim incelendi. Takviyedeki katman diziliş değişiminin etkisi hesaplanarak optimum diziliş elde edildi. Aynı kütlede takviyesiz ve takviyeli plakalar oluşturularak, takviyenin etkinliği hakkında yorumlar yapıldı. Farklı kesit alanına sahip, aynı kütlede ve yükseklikte takviyeler kullanılarak, kesit alanının analiz sonuçlarına etkisi gözlemlendi. Hacim ve kesit alanı sabit tutularak metal malzemelerden oluşturulmuş takviyeler kullanıldı. Ağırlık göz önünde bulundurularak, takviye için malzeme seçiminin çökme, gerilme ve doğal frekans değerlerine etkisi incelendi. Son olaraksa takviyenin doğrultusu değiştirilerek aynı ağırlıkta çift takviye kullanımının ortaya çıkardığı değişim yorumlandı.
Özet (Çeviri)
Composite materials which are developed as lighter and stronger materials for the aerospace industry in the 1960s have now become widespread and been used in many industries such as marine, construction and automotive. They provide a better alternative to old standby materials like aluminum, steel, wood and concrete. In particular composite materials combine high strength and low weight together, while at the same time they have high resistance to corrosive and thermal effects. They provide great weight savings because of the specific properties and low weight of the individual components which form the composite material. They also have high impact strength and design flexibility. Correspondingly they can be designed for a particular type of load. All these characteristics make composite materials indispensable for the aeronautical and aerospace structures. Composite materials that are used in aerospace structures are usually built up with laminates where unidirectional fabric layers are stacked on top of each other in different orientations to give the structure maximum stiffness where it is needed. Cutting edge technology aircrafts substantially comprise stiffened laminated composite plates in many parts. For laminated composite plates, orientation of fibers is the most important case that effects plates strength and rigidity. Focusing on this parameter for different boundary conditions results in lighter and stronger structures. In addition to that, there are other significant parameters for stiffened composite plates such as direction, shape and material. All these parameters should be considered together to obtain structures that have higher strength and lower weight. In this study, optimum fiber orientation for square and rectangular laminated plates and optimum shape, direction and material for stiffeners are examined. First, a general information about composite materials and plate equations is given. Then, some composite plates and stiffened composite plates samples are formed, and static and dynamic analyses are conducted to compare those plates, and finally better combinations are determined. ANSYS 16.2 ACP module is used for design procedure and analysis performed in ANSYS Workbench 16.2. Some analytical formulas available in literature are used for validation of analysis of bare plates. In this context, numerical analysis is performed for bare laminated composite plates and stiffened laminated composite plates. First, a square laminated composite plate with 8 epoxy-carbon unidirectional layers considered. Edge length of the square plate is chosen as 500 mm and thickness of the plate as 4 mm., Free vibration and static analysis under distributed load of plates are examined for different fiber orientations of layers under different boundary conditions. For all sides simple supported case, minimum deflection and maximum fundamental natural frequency occur at (45,-45)4 orientation. For all sides clamped case, minimum deflection and maximum fundamental natural frequency occur at (0,0)4 and (90,90)4 orientations. (45,-45)4 orientation yields lower stress levels for both cases. Free vibration analysis is also performed for different boundary condition combinations such as SSSS, CCCC, CSCS, CCSS, CCFC, SSCS, SSFS, SSFF and CCFF. Best angle orientations for each case are provided. Analyses that are performed for all side simple supported and all side clamped boundary conditions are repeated for rectangular plates by changing aspect ratio to 1/2, 1/3 and 1/4. Laminated rectangular plates with fibers along the short edge produce less deflection and higher fundamental natural frequency for both boundary conditions. However, higher natural frequencies increase for (45,-45)4 orientation. Second, a laminated composite plate is designed with dimensions Lx=500mm and Ly=1000mm. A comparison between bare plate and stiffened plate with the same weight is made and it is found that stiffeners reduce the deflections and stresses of plate but, increase natural frequencies significantly. The use of stiffener also changes mode shapes. In order to see the effect of the stiffener cross sectional shape, different profiles such as rectangular, I, T, inverse-T, L, inverse-L and Z shaped composite stiffeners with the same height and volume are designed by using the same type layers of the plate. Stiffeners are oriented along the y- direction and at the middle of the plate. Static analysis is conducted under 1 kPa distributed pressure on the top surface of the plate. Maximum deflection and stress are obtained under all side clamped boundary conditions. It is found that inverse-T shaped stiffener results in less deformation and stress levels. The order of maximum deflection and maximum stress levels for each stiffener is inverse-TL>I>Z>rectangular>T>inverse-L. For higher modes, it is found that natural frequencies don't change significantly. Harmonic response analysis of each sample is performed from 1 Hz to 1000 Hz under distributed 1 kPa pressure on the top surface of the plate. Frequency response of the plate is observed. It is seen that samples reach their peak values at their fundamental natural frequencies. The order of amplitude values at peak points is inverse-T
Benzer Tezler
- Ön gerilmeli elyaf takviyeli kompozit malzemelerin deneysel ve teorik incelenmesi
Başlık çevirisi yok
NEVZAT TARIM
- Multi-objective optimization of fiber reinforced laminated hybrid composite plates using particle swarm algorithm
Fiber takviyeli katmanlı hibrit kompozit plakaların parçacık sürü algoritması ile çok amaçlı optimizasyonu
ORHAN NURİ YEGİT
Yüksek Lisans
İngilizce
2024
Havacılık ve Uzay Mühendisliğiİstanbul Teknik ÜniversitesiUçak ve Uzay Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ KAAN YILDIZ
- İnce cidarlı ve bal peteği takviyeli kompozit plakların anlık basınç yükü altındaki dinamik davranışlarının deneysel ve sayısal yöntemlerle incelenmesi
Experimental and numerical investigation of the dynamic behavior of thin-walled and honeycomb reinforced composite plates under blast load
LİNA İRTEGÜN
Yüksek Lisans
Türkçe
2022
Gemi MühendisliğiYıldız Teknik ÜniversitesiGemi İnşaatı ve Gemi Makineleri Mühendisliği Ana Bilim Dalı
DOÇ. DR. İSMAİL BAYER
PROF. DR. HALİT SÜLEYMAN TÜRKMEN
- Doğal elyaf takviyeli kompozitlerden oluşturulmuş sandviç yapıların balistik performanslarının incelenmesi
Analysis of ballistic performance of sandwich structures made of natural fiber reinforced composites
MERT DEMİR
Doktora
Türkçe
2024
Makine MühendisliğiErciyes ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. RECEP EKİCİ
- Vibration analysis of skew fiber-reinforced composite laminated plates
Çarpık fiber takviyeli kompozit tabakalı plakaların titreşim analizi
GÜRKAN GÖKER
Yüksek Lisans
İngilizce
1999
Makine MühendisliğiBoğaziçi ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. GÜNAY ANLAŞ