Geri Dön

Yonga levha üretiminde toz üre kullanımının formaldehit emisyonu üzerine etkileri

The effects of urea powder usage on the formaldehyde emission in particleboard manufacturing

  1. Tez No: 465119
  2. Yazar: ÖZCAN YÜCE
  3. Danışmanlar: PROF. DR. FATİH MENGELOĞLU
  4. Tez Türü: Yüksek Lisans
  5. Konular: Metalurji Mühendisliği, Metallurgical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2017
  8. Dil: Türkçe
  9. Üniversite: Kahramanmaraş Sütçü İmam Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Orman Endüstri Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 89

Özet

Yongalevhalar masif malzemeye göre sağlamış oldukları bazı avantajlar nedeni ile özellikle iç mekânlarda yoğun bir şekilde kullanılmaktadır. Bu levhaların avantajlarının yanı sıra bazı dezavantajları da mevcuttur. Üretimlerinde kullanılan tutkal türüne ve üre/formaldehit mol oranına göre nihai üründe formaldehit emisyonuna neden olmaları yonga levhaların en önemli dezavantajıdır. Uluslararası Kanser Araştırma Örgütü (IARC)'nün 1995 yılında formaldehiti insan sağlığı açısından“Muhtemel Kanserojen Maddeler”sınıfına dahil etmiş, 2004 yılında aynı örgütün yürütmüş olduğu daha kapsamlı araştırmalar sonucunda formaldehit doğrudan insan sağlığı açısından“Kanserojen Madde”olarak tanımlanmıştır. Bu nedenle formaldehit emisyonunun düşürülmesi insan sağlığı açısından hayati önem taşımaktadır. Bu tez çalışmasında yongalevha üretiminde farklı boyutlarda (

Özet (Çeviri)

Particleboards are extensively used in indoor applications due to their some advantages over massive wood. In addition to the advantages, there are also some disadvantages of particleboards. The most important disadvantage is formaldehyde emission which occurs from adhesive according to the molar ratio of urea / formaldehyde. The formaldehyde was identified as“Possible Carcinogenic Substance”as a result of their studies in 1995 by International Agency for Research on Cancer (IARC). With the more extensive investigations of the same group in 2004, formaldehyde was declared as“Carcinogenic Substances”. For that reason, reducing of the formaldehyde emission is vital for human health. In this study, the effects of different size and rate of urea powder on the formaldehyde emission in the manufacturing of particleboard were investigated. In addition, the effect of how urea powder was used (with and without adhesive) on formaldehyde emission was also investigated. Two different sizes (Large, Small) and five different rates of urea (1, 2, 3, 4 and 5%) were used for particleboard manufacturing. Ureaformaldehyde (1,35 mol) adhesive was used for production of three layered particleboards. Formaldehyde emission properties were examined by perforator method according to EN 120. Furthermore, mechanical and physical properties including bending strength, modulus of elasticity, internal bond strength, surface stability, thickness swelling and water absorption of the samples were determined according to EN 310, EN 319 and EN 317 standards, respectively. Formaldehyde emission values was decreased with the mixing of the urea powder with chips prior to gluing and the produced boards were E0 grade boards in terms of formaldehyde emission. The size and rate of the urea powder were statistically effective on the mechanical and physical properties of the produced boards. In addition, all of the boards in this group satisfied the required standards. It should be noted that slight decrease of mechanical and physical properties were observed. The usage method of the urea powder also has a significantly effect on particleboards properties (formaldehyde emission, mechanical and physical properties). As a result, it was determined that mixing of the urea powder passing through the 0.2 mm sieve with the chips before gluing showed better results.

Benzer Tezler

  1. Melamin emdirilmiş kağıt (MEK) atıkların yonga levha üretiminde değerlendirilmesi

    Utilization of melamine impregnated paper waste (MIP) in particleboard manufacturing

    İBRAHİM HALİL BAŞBOĞA

    Doktora

    Türkçe

    Türkçe

    2018

    Endüstri ve Endüstri MühendisliğiKahramanmaraş Sütçü İmam Üniversitesi

    Orman Endüstri Mühendisliği Ana Bilim Dalı

    PROF. DR. FATİH MENGELOĞLU

  2. Eko tasarım: Mobilya üretiminde kullanılan bazı vernik, tutkal ve ahşap esaslı levhalarda açığa çıkan gazların tespiti ve salınımlarının analizi

    Eco design: Determination of gases released in some varnishes, glues and wood-based boards used in furniture production and analysis of their emissions

    HALDUN ENDER ERDEM

    Doktora

    Türkçe

    Türkçe

    2024

    Ağaç İşleriGazi Üniversitesi

    Ağaç İşleri Endüstri Mühendisliği Ana Bilim Dalı

    PROF. DR. HAMZA ÇINAR

  3. Çeşitli nano malzeme ile güçlendirilmiş odun esaslı levhaların karakteristik özelliklerinin belirlenmesi

    Determination of characteristic properties of wood- based boards reinforced with various nano material

    KADİR DOĞAN

    Doktora

    Türkçe

    Türkçe

    2024

    Ağaç İşleriKastamonu Üniversitesi

    Orman Endüstri Mühendisliği Ana Bilim Dalı

    DOÇ. DR. ALPEREN KAYMAKCI

  4. Sunta sanayisinde yonga kurutucusunun ısı ekonomisi

    The heat economy of dryer the wood shaving at chipboard industries

    ÖZGÜR SELÇUK

    Yüksek Lisans

    Türkçe

    Türkçe

    2003

    Makine MühendisliğiSüleyman Demirel Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. MEHMET KUNDUZ

  5. Yonga levha üretiminde su bazlı tutkalların kullanımı

    Studying on the usage of water based adhesives in particle board production

    EMRE TEKİN

    Yüksek Lisans

    Türkçe

    Türkçe

    2004

    Ağaç İşleriHacettepe Üniversitesi

    Ağaç İşleri Endüstri Mühendisliği Ana Bilim Dalı

    PROF.DR. MEHMET DOĞAN