Geri Dön

Pülverizatör memelerinde püskürtme paterni değişkenlerinin doğrusal hareketli simülatörde belirlenmesi

Determination of the spray pattern variables of the sprayer nozzles using a linear moving simulator

  1. Tez No: 483635
  2. Yazar: MEHMET ŞAHİN
  3. Danışmanlar: DOÇ. DR. BAHADIR SAYINCI
  4. Tez Türü: Yüksek Lisans
  5. Konular: Ziraat, Agriculture
  6. Anahtar Kelimeler: Konik hüzmeli meme, meme hüzme açısı, püskürtme testi, uygulama hacmi, Hollow cone nozzle, nozzle spray angle, spray test, application rate
  7. Yıl: 2017
  8. Dil: Türkçe
  9. Üniversite: Atatürk Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Tarım Makineleri Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 110

Özet

Bu çalışmanın amacı; pülverizatör memelerinin püskürtme paterni özelliklerini belirlemek için deneysel ve istatistiksel bir model ortaya koymaktır. Bu amaçla, pülverizatör memelerinde püskürtme paterni testlerini gerçekleştirmek için geliştirilen hız kontrollü doğrusal hareketli bir simülatör kullanılmış ve yapılan testler paternatör bulgularıyla karşılaştırılmıştır. Püskürtme paterni testlerinde 20 adet içi boş konik hüzmeli meme plakası kullanılmıştır. Püskürtme uygulamaları 4 bar sabit işletme basıncı ve 80 cm sabit püskürtme yüksekliğinde yapılmıştır. Doğrusal hareketli simülatör testlerinde püskürtme paterni için suya duyarlı kartlar kullanılmış ve denemeler 100 lt ha-1, 150 lt ha-1 ve 200 lt ha-1 uygulama hacimlerinde yapılmıştır. Denemelerde püskürtme paterniyle ilgili püskürtme genişliği, meme hüzme açısı, çarpıklık katsayısı, basıklık katsayısı, püskürtme paterni düzgünlüğü (patern CV'si) ve 50 cm meme aralığında hacimsel dağılım düzgünlüğü (CV@50 cm) değişkenleri belirlenmiştir. Ayrıca her bir meme plakasında debi, yüzey kaplama oranı ve damla yoğunluğu ölçümleri yapılmıştır. Diskriminant analizi sonuçlarına göre meme plakalarını tanımlayan ayırma fonksiyonlarının meme plakalarını doğru sınıflandırma oranı paternatör testlerinde %85.0; 100 lt ha-1, 150 lt ha-1 ve 200 lt ha-1'da yürütülen simülatör testlerinde sırasıyla %88.3, %91.7 ve %95.0 olarak bulunmuştur. Eşli karşılaştırma testi sonuçlarına göre püskürtme paterni açısından paternatör ve simülatör testleri, patern CV'si ve çarpıklık değişkenleri hariç çok önemli düzeyde farklı bulunmuştur. Ancak her iki yöntem arasındaki korelasyonun anlamlı olduğu saptanmıştır. Doğrusal hareketli simülatörde yürütülen denemelerde en uygun uygulama hacminin 150 lt ha-1 olduğu belirlenmiştir. Meme debisi kontrolünde ±%10 debi sınırının dışında 5 adet memenin olduğu saptanmıştır. Paternatör testlerinde 11 adet ve 150 lt ha-1'da yürütülen simülatör testlerinde 14 adet memenin püskürtme paterni açısından farklı olduğu tespit edilmiştir. Simülatör testlerinde tespit edilen meme plakaları, debi sapma sınırı ve paternatör testlerinde tespit edilen meme plakalarını kapsamıştır. Sonuç olarak doğrusal hareketli simülatör testlerinde püskürtme paterni açısından düzgün olmayan memelerin yüksek bir doğrulukla tespit edilebileceği saptanmıştır. Görüntü işleme tekniği açısından yapılan değerlendirmelerde suya duyarlı kart görüntülerinde belirlenen değişkenler arasında önemli ilişkilerin olduğu saptanmıştır. Kart görüntülerinin gri tonlama seviyesi (Gs) ve yüzey kaplama oranı (Yk, %) değişkenleri arasında eşitliği (Y_k=-0.00094∙G_s^2-0.143∙G_s+86.03 ) olan polinamiyal bir ilişki (R2= 0.941) bulunmuştur. 2017, 97 sayfa

Özet (Çeviri)

The aim of this study is to reveal an experimental and statistical model for determining the spray pattern features of the sprayer nozzles. For this aim, a linear moving simulator controlled operating speed was used to carry out the spray pattern tests of sprayer nozzles, and the test results were compared to the patternator outputs. For the spray pattern tests, the hollow cone nozzle discs of 20 in number were tested. The spray application was done at constant spray pressure of 4 bars and spray height of 80 cm. Water sensitive papers were used for the spray pattern trials conducted on the linear moving simulator, and the trials were done at the application volumes of 100 l ha-1, 150 l ha-1 and 200 l ha-1. In the trials relating to the spray pattern, the variables spray actual width, nozzle spray angle, skewness coefficient, kurtosis coefficient, spray pattern uniformity (pattern CV) and volumetric distribution uniformity at the nozzle distances of 50 cm (CV@50 cm) were determined. Besides, the flow rate, spray coverage and droplet density were measured for each of the nozzle discs. In references to the discriminant analysis results, the correctly classification rate of the nozzle discs by the discriminant functions which describes the hollow cone nozzle discs were found as 85.0% for the patternator tests; 88.3%, 91.7% and 95.0% for the simulator tests at the application rates of 100 l ha-1, 150 l ha-1 and 200 l ha-1, respectively. According to the results of the paired-comparing test, the patternator tests and the simulator tests were significantly found different each other excluding the variables of the pattern CV and the skewness from the respect of the spray pattern. But, the correlation between the both of the test methods were determined to be significant. In the trials conducted on the linear moving simulator, the most convenient application volume was found to be 150 l ha-1. In the controlling of the nozzle flow rate, the nozzle discs of 5 in number were confirmed excluding the flow rate limits of ±10%. The nozzle discs of 11 in number in the patternator tests, and 14 in number in the patternator tests in the simulator tests conducted at the application volume of 150 l ha-1 were revealed to be different in the respect of the spray pattern. These nozzle discs fixed by the simulator tests covered the nozzles determined at the tests of the flow rate limit and the patternator. In conclusion, the uneven spray nozzles in terms of the spray pattern were appointed to be confirmed with a high accuracy by the linear moving simulator tests. In terms of the assessments done with regard to the image processing techniques, a significant relationship among of the variables determined on the water sensitive papers was revealed. The among of the gray level (Gs) of the paper images and their spray coverage (Yk, %) variables was found a polynomial relation with high R2 (0.941), (Y_k=-0.00094∙G_s^2-0.143∙G_s+86.03 ) 2017, 97 pages

Benzer Tezler

  1. Püskürtme paterni test ünitesinin tasarımı, imalatı ve pülverizatör memelerinde akış kontrolü

    Design, manufacture of spray pattern test unit and flow control of sprayer nozzles

    RUÇHAN ÇÖMLEK

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    ZiraatAtatürk Üniversitesi

    Tarım Makineleri ve Teknolojileri Mühendisliği Ana Bilim Dalı

    DOÇ. DR. BAHADIR SAYINCI

  2. Pülverizatör memelerinde püskürtme açısı ve akış düzgünlüğünün görüntü işleme operasyonuyla belirlenmesi

    Determination of spraying angle and flow evenness in pulverizator noozles by image porcessing operation

    NECATİ ÇETİN

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    ZiraatErciyes Üniversitesi

    Biyosistem Mühendisliği Ana Bilim Dalı

    DOÇ. DR. CEVDET SAĞLAM

    YRD. DOÇ. DR. BÜNYAMİN DEMİR

  3. Herbisit uygulamalarında kullanılan düşük sürüklenme potansiyelli memelerin püskürtme tekniği ve biyolojik etkinlik açısından değerlendirilmesi

    Evaluation of spray application performances and biological efficiency of low drift nozzles in herbicide application

    ALPER SOYSAL

    Doktora

    Türkçe

    Türkçe

    2005

    ZiraatÇukurova Üniversitesi

    Tarım Makineleri Ana Bilim Dalı

    PROF.DR. ALİ BAYAT

  4. Pülverizatör memelerinde işletme basıncı ve konum açısının damla taşınımına etkisi

    Effects of operational pressure and position angle on drop transport of pulverizator nozzles

    EMEL SARI

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    ZiraatErciyes Üniversitesi

    Biyosistem Mühendisliği Ana Bilim Dalı

    DOÇ. DR. BÜNYAMİN DEMİR

    DOÇ. DR. BAHADIR SAYINCI

  5. Konik hüzmeli pülverizatör memelerinde elektrostatik yükleme tekniğini kullanarak pülverizasyon karakteristiklerini iyileştirme olanakları

    The Progressive of spraying characteristics of cone type nozzles by using electrostatics technics

    ERGİN DURSUN

    Yüksek Lisans

    Türkçe

    Türkçe

    1990

    ZiraatAnkara Üniversitesi

    Tarımsal Mekanizasyon Ana Bilim Dalı

    DOÇ.DR. İBRAHİM ÇİLİNGİR