Bir binek araç için çift aksonlu Macpherson tipi ön süspansiyon sisteminde kullanılacak bilyalı kutu tipi ve kremayer tipi direksiyon sistemlerinin geliştirilmesi
Development of recirculating ball and nut and rack and pinion type steering systems to be used with double axis Macpherson front suspension for a passenger car
- Tez No: 511549
- Danışmanlar: PROF. DR. İSMAİL MURAT EREKE
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2018
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Otomotiv Bilim Dalı
- Sayfa Sayısı: 127
Özet
Günümüzde gelişen araç teknolojileri ile birlikte özellikle elektrikli araçlar üzerinde yapılan çalışmalar artmakta ve büyük otomotiv üreticileri de elektrikli araçlara daha fazla yatırım yapmaktalardır. Elektrikli araçlar ile birlikte enerji tüketimi, güvenlik önlemleri ve sürücü odaklı tasarımlar da önem kazanmaktadır. Direksiyon sistemleri de gelişen teknoloji ile birlikte daha farklı tasarımlara yönelmekte, enerji tüketimi az ve müşteri odağı daha fazla olan sistemler üretici firmalar tarafından geliştirilmektedir. Bu çalışmada önden çekişli bir binek araç için çift aksonlu Macpherson tipi ön aks süspansiyonunda kullanılan hem sağdan hem de soldan direksiyonlu iki farklı direksiyon sistemi tasarımı yapılmıştır. Tasarımı yapılmış araç için ön aks sistemi ortak kullanılmak üzere farklı pazarlarda kullanımı düşünülen iki farklı direksiyon sistemi tasarımı gerçekleştirilmiştir. Sağdan direksiyonlu araç için ihale şartnamesi olan U-dönüş çapı 8,535m olan bir direksiyon sistemi tasarlanmıştır. Şartnamede sürücünün iki duvar arasındaki mesafesi 8,535m olan bir yerden duvarlardan birinden paralel bir şekilde hareketine başlaması ve geri geri gitmeden karşı duvardan dönebilmesi talep edilmektedir. Dönüş yarıçapı hedefi göz önünde tutularak aracın boyutlarında bazı değişikliklere gidilmiştir. Yapılan araştırmalarda sadece ön aks yönlendirmesi yapılarak aracın istenilen dönüş yarıçapını sağlaması hedeflenmiştir. Bu sebeple de istenilen dönüş yarıçapını sağlayacak teker dönüşüne imkan veren çift aksonlu Macpherson tipi ön süspansiyon sistemi tercih edilmiştir. Genellikle ağır ticari vasıtalarda (kamyon, tır, otobüs vb.) ve offroad araçlarında tercih edilen kutu tipi bilyalı (recirculating ball and nut – RCB - ) direksiyon kutusunun bu araçta kullanılması gerekli görülmüştür. Bahsi geçen direksiyon kutusu ile birlikte ek olarak kullanılan bağlantı parçalarının, braketlerin ve direksiyon kutusunun araca adapte edilmesi gerekmektedir. Aracın boyutları, yolcu kapasitesi, motor lokasyonu ve tipi (önden motorlu, elektrikli motor) ile çarpışma test şartnamalerinin gereklilikleri düşünüldüğünde direksiyon kutusunu ve bahsi geçen diğer direksiyon bağlantı parçalarını içeren bir direksiyon sistemi tasarımı gerçekleştirilmiştir. Aynı ön aks kullanılmak üzere aracın soldan direksiyonlu kremayer tipi direksiyon sistemine sahip bir versiyonu daha çalışılmıştır. Bu sayede ortak bir ön aks geliştirilmesi yapılarak aracın hem sağdan direksiyonlu Londra Belediyesi isterlerini sağlayan hem de soldan direksiyonlu başka pazarlarda binek araç olarak kullanılabilecek bir versiyonu tasarlanmıştır. Çalışma esnasında öncelikle yüksek dönüş açılarına müsaade edebilen çift aksonlu Macpherson tipi ön süspansiyon sisteminden bahsedilmiştir. Direksiyon sistemi parametrelerini etkileyen ve geometrik olarak direksiyon sistem parçalarına girdiler veren ön düzen geometrisine değinilmiştir. Sonrasında ise hem sağdan direksiyonlu araç için kullanılan kutu tipi bilyalı direksiyon sisteminden hem de soldan direksiyonlu araç için kullanılan kremayer tipi direksiyon sistemi tasarımından bahsedilmiştir. Bu sayede iki farklı direksiyon sistemi karşılıklı olarak incelenmiştir. Bilyalı kutu tipi direksiyon sistemi tasarımında direksiyon kutusu torkunu belirleyebilmek için park halinde teker döndürme momentinin hesaplanmasını içeren bir metot geliştirilmiştir. Daha sonra dönüş yarıçapını sağlayacak direksiyon kinematiğinden ve direksiyon sistemi parçalarının tasarımlarına girilmiştir. Özellikle araç tasarımlarında ortaya çıkan proje başında kabul edilen ağrılıkların proje sonlarına doğru değişmesi konusu için de değişen ağırlıkların direksiyon dönme karakteristiğine olan etkileri ve bu etkilerin düzeltilmesi için yapılan çalışmalara değinilmiştir. Farklı çevrim oranları ile dönme karakteristiklerindeki değişimlere de bakılmıştır. Aynı metodoloji kullanılarak kremayer tipi direksiyon sistemi de incelenmiş ve tasarımları gerçekleştirilmiştir. Böylelikle bilyalı kutu tipi ve kremayer tipi direksiyon sistemleri aynı metrik kriterler içerisinde tasarlanmış olmaktadır. Son olarak ise araç dinamiği açısından da irdelenen farklı direksiyon çevrim oranlarından hem bilyalı kutu tipi için hem de kremayer tipi sistem için en uygun çevrim oranının belirlenmesi konusu incelenmiştir. Çevrim oranı seçiminde literatürde steering catch olarak adlandırılan hadiseye bakılmıştır. Elektro-hidrolik direksiyon tahrik mekanizmasında farklı modellerdeki hazır pompa ünitelerinin kapasiteleri ile çevrim oranları iki farklı direksiyon sistemi için de incelenmiş ve en uygun çevrim oranı seçilmiştir.
Özet (Çeviri)
With developing vehicle technologies in nowadays, work on electric vehicles is increasing, and major automotive manufacturers are investing more in electric vehicles. Energy consumption, safety precautions and customer-oriented designs are also important in conjunction with electric vehicles. Steering systems tend to be different designs with developing technology, systems with less energy consumption and more customer focus are being developed by the manufacturers. In this study, two different steering systems with right-hand and left-hand steering were used for a front wheel drive passenger car with a double axis Macpherson type front axle suspension. Two different type of steering system concepts were designed for use in different markets and each type of them is suitable to use with same front axle system for the common use of the vehicle. A steering system that has a capability to reach U-turn diameter of 8,535 meter was designed for the right-hand drive vehicle. It is demanded in the tender request of London taxi that the driver is able to start his movement in parallel from one of the walls at a distance of 8,535m between the two walls and to return from the opposite wall without going back and forward. Some changes have been made in the dimensions and layout of the vehicle in consideration of the turning radius target. In the benchmark researches carried out, only front axle steering is aimed to provide the desired turning radius of the vehicle. For this reason, a double axis Macpherson type front suspension system has been selected in order to allowe the wheel to turn to provide the desired turning radius. It is generally deemed necessary to use recirculating ball and nut (RCB) steering gears on heavy commercial vehicles (trucks, buses etc.) and also off-road vehicles. Recirculating ball and nut steering gear must be accompanied by an additional set of parts and brackets. A steering system design has been carried out that includes the steering box and other steering linkage components, as the vehicle dimensions, load capacity, engine location and type (front wheel drive engine, electric motor), collision test requirements and the other regulations are considered. A further version of the vehicle with a left-hand drive rack and pinion steering system has been worked on for the same front axle. A common front axle has been developed on this side to enable the vehicle to be used both as a right-hand drive version with respect on the London city requirements and as a passenger car in other markets with left-hand drive. During thesis studies, a double axis Macpherson type front suspension system, which allows for high turn angles, is mentioned first. The front suspension geometry, which affects steering system parameters and geometrically limits the steering system components such as kingpin axis, caster angle, caster trail, camber angle, scrub radius, is worked and decided. And after that, we talked about the design of a recirculating ball and nut steering system for both right hand drive cars and a rack and pinion steering system for left hand drive vehicles. In this case, two different steering systems performance were examined mutually. A method has been developed that includes calculating the self aligning wheel torque in parking condition in order to determine maximum output steering box torque in the design of a recirculating ball and nut type steering system. It is examined on Mitchke's and bore torque formulas regarding on the self aligning torque. It is observed that Mitchke's formula is more likely considered on the front suspension geometry and not considered the tire effects. That's why the self alignin moment which is calculated from it is not sufficient enough and not simulate the real life exactly. On the other side bore torque method is developed in order to find out the self aligning torque, but in this method you have to be known all tire parameters such as contact patch and elastokinematic behaviours. This method is not so easy to reach. In the thesis, in order to find the self aligning torque without measuring the tire parameters, some measurements had been done on the another vehicle. With respect on the Mitchke's formula and measurements on the another vehicle, the self aligning torque is calculated. In the following sections the steering kinematics to provide the demanded turning radius and the design of the steering system components. Steering gear box geometrically packaged into the vehicle and different gear ratios are investigated both vehicle dynamics and steering performance. Steering linkage parts such as steering column, I-shaft, pitman arm, draglink, intermediate rod, tie rod and relay lever arms are also designed with considering the limits of packaging area, hardpoints which is coming from kinematic analysis and the durability of the parts. Steering column, I-shaft and pinion shaft location of the RCB gear is designed and packaged according to the target of the non-uniformity which is directly related on the angular velocity and steering wheel torque. Basically, non-uniformity of the angular velocities of the joints are packaged with considering the all position of the steering column. Non-uniformity of the joints is calculated with a formula in basically. Designer and engineers started to design their own system with some initial acceptance criteria. Total weight and weight distribution is some of these acceptance criteria. It is a common issue with changings the weights in the middle of the vehicle design project. In particular, the effects of varying weights on steering turn characteristics especially understeer gradient and the work done to correct these effects have been addressed in order to change the accepted weight at the beginning of the project, which emerged in vehicle designs, towards the end of the project. Without redesign the suspension geometry, just making small modification on the steering system parameters, bad effect of the changing weight distribution is eliminated. Variations in the turning characteristics of the vehicle with different steering ratios are also examined. Using the same methodology, the rack and pinion steering system was also investigated and designed. Rack force is calculated with same formula and method in the RCB gear section. Rack and pinion dimensions such as inner and outer tie rod locations, pinion tower angle, length and subframe connections of the rack and pinion is designed with the limits of the other parts in vehicle and steering kinematics. Rack gear ratios are also investigated with regarding on the turning characteristics and steering catch performance. Thus, the ball and nut type and rack type steering systems are designed with the same metric criteria. Finally, the issue of determining the optimum steering ratio for both recirculating ball and nut type and rack and pinion type steering system. It has been examined from different steering gear ratios which are also examined in terms of vehicle dynamics. In the selection of the steering gear ratio, steering catch performance is examined. In the electro-hydraulic steering drive mechanism, the capacities of the off the shelf pump units in different models and different type of steering gear ratios for both rack and pinion and RCB gear were also examined for two different steering systems and the optimum steering gear ratio was selected.
Benzer Tezler
- Wankel motoru ve çevrim atlatma sisteminin deneysel ve sayısal olarak incelenmesi
Experimental and numerical investigation of the Wankel engine and skip cycle system
ÖMER CİHAN
Doktora
Türkçe
2017
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. OSMAN AKIN KUTLAR
- 3 LT dizel motorun çift kademeli turboşarj sisteminden tek kademeli turboşarj sistemine dönüştürülmesi
Investigation and optimization of the engine parameters when switching to single turbocharger from bi-turbocharger in the 3L V6 engine
VEYSEL TEKÇE
Yüksek Lisans
Türkçe
2015
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. HİKMET ARSLAN
- Development and control of an active torsional vibration damper for vehicle powertrains
Taşıt güç aktarma sistemleri için aktif torsiyonel titreşim damperi geliştirilmesi ve kontrolü
ALİŞAN YÜCEŞAN
Doktora
İngilizce
2021
Mekatronik Mühendisliğiİstanbul Teknik ÜniversitesiMekatronik Mühendisliği Ana Bilim Dalı
PROF. DR. ATA MUGAN
- Adaptive equivalent consumption minimization strategy with driving pattern recognition for hybrid electric vehicles
Hibrit elektrikli araçlar için sürüş tanıma ile uyarlanabilir eşdeğer yakıt tüketimi minimizasyonu stratejisi
BARIŞ KALAYCI
Yüksek Lisans
İngilizce
2021
Bilgisayar Mühendisliği Bilimleri-Bilgisayar ve Kontrolİstanbul Teknik ÜniversitesiMekatronik Mühendisliği Ana Bilim Dalı
DOÇ. DR. VOLKAN SEZER
- Seyahat otobüslerinde ECE-R/66-02 regülasyonuna göre tasarlanan yanduvar-altyapı bağlantı konseptinin optimizasyonu
Optimization the node concept of the base structure –side wall, which was desinged according to ECE-R/66-02 regulaton on coaches
AHMET KOŞTUROĞLU
Yüksek Lisans
Türkçe
2018
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. İSMAİL MURAT EREKE