Yatay boru üzerindeki havuz kaynamanın incelenebileceği deney düzeneği tasarımı ve aseton için havuz kaynamanın deneysel olarak incelenmesi
Experimental setup design for pool boiling on horizontal tube and experimental investigation of pool boiling of acetone
- Tez No: 517174
- Danışmanlar: PROF. DR. MUSTAFA ÖZDEMİR
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2018
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Isı-Akışkan Bilim Dalı
- Sayfa Sayısı: 101
Özet
Kaynama ısı geçişi, endüstriyel ürünlerde sıkça karşılaşılan bir ısı geçişi türüdür. Evaporatörler, buhar kazanları, ısı boruları kaynama ısı geçişin görülebileceği ticari ürünlere örnek verilebilir. Bu ürünler tasarlanırken, maliyet etkisinden dolayı, küçük yüzey alanından büyük ısı geçişi sağlanması hedeflenir. Bu nedenle de, tasarım için kaynama ısı taşınım katsayı oldukça önemli bir parametredir. Kaynama ve taşınım ısı geçişi arasında bazı benzer noktalar olmasına rağmen, kaynamadaki faz değişimi nedeni ile kaynamadaki ısı geçişi çok daha karmaşık bir yapıda gerçekleşir. Fakat, her iki ısı geçişi şekli de katı bir yüzey ile akışkan arasında gerçekleştiği için matematiksel olarak formule edilirken ısı taşınım katsayısı ifadesi kullanılır. Kaynama olayındaki faz değişimi ve faz değiştiren moleküllerin hareketleri, kaynamadaki ısı taşınım katsayısının teorik olarak ifade edilmesini zorlaştırır. Bu nedenle, kaynama için literatürde çoğunlukla deneysel çalışmalar sonucunda elde edilmiş ampirik bağıntılar yer almaktadır. Deneysel olarak, kaynama ısı taşınım katsayısı, temel olarak ısı akısının kızma farkına bölünmesi ile hesaplanır ve hesaplanan değer sadece yapılan deney şartlarında geçerlidir. Bu tez kapsamında, farklı basınçlar altında, boru üzerinde gerçekleşen kaynamanın incelebileceği bir deney tesisatı tasarlanmış ve sonrasında aseton için bazı sıcaklık ve basınç değerlerinde havuz kaynama incelenmiştir. Havuz kaynamanın önemli parametrelerinde bir tanesi de basınç değeridir. Bu nedenle deney düzeneği farklı basınçlar ile deney yapabilmek adına kapalı bir devre olarak tasarlandı. Deney düzeneği, temel olarak bir adet evaporatör tankı, bir adet su soğutmalı kondenser tankı olarak tasarlandı ve bu iki tank alt ve üst taraflardan borular bile birbirine bağlanarak kapalı bir devre oluşturuldu. Silindir şeklindeki evaporatör tankına içerisinde elektrikli ısıtıcı olan, üzerindeki kaynamanın inceleneceği boru yerleştirilmiştir. Boru içerisindeki elektrikli ısıtıcı 220 V gerilim altında 2300 W ısıl güç sağlayabilmektedir. Evaporatörde boru üzerinde kaynayan akışkan faz değiştirerek yükselmekte ve kondenser tankına girmektedir. Burada yoğuşan akışkan da kondenser tankının altında birikerek, bileşik kaplar prensibine göre tekrar evaporatör tankına geri dönmektedir. Evaporatörde verilen ısı ile kondenserde çekilen ısının birbirine eşit olduğu durumda, sistemde rejim halinde kaynama gözlemlenecektir. Farklı basınçlarda deney yapılması istendiğinde ise, deneye başlamadan önce vakum pompası ile sistemin içindeki hava ve akışkan buharı sistemden uzaklaştırılmalıdır. Deney tesisatı farklı borular ve akışkanlar için, farklı basınç ve sıcaklık değerlerinde kaynamanın incelenmesine olanak verecek şekilde tasarlanmıştır. Aynı zamanda evaporatör tankına eklenen gözetleme camı ile, boru üzerindeki kaynama görsel olarak da incelenebilmektedir. Deney sırasında evaporatördeki homojen sıcaklığının korunması için, kondenser tankına bir adet ön ısıtıcı eklenmiştir. Bu ön ısıtıcı evaporatör tankından aldığı sıcaklık sinyali ile çalışan bir PID kontrol devresi ile çalışmaktadır. Böylece, kondenserde yoğuşan ve aşırı soğuyan akışkan evaportör tankına doyma sıcaklığında dönecektir ve evaporatördeki sıcaklık dağımınını etkilemeyecektir. Bu sayede ana ısıtıcıdan sağlanan ısıl gücün tamamının kaynama için kullanılacağından emin olunmuştur. Bu tez kapsamında, asetonun düz çelik boru üzerindeki havuz kaynaması incelenmiştir. Rejim halinde istenilen basınç değeri elde edildikten sonra, çelik boru üzerine yerleştirilen termo elemanlar ile yüzey sıcaklığı belirlenmiş, evaporatör tankı üzerindeki basınç trasnmitterinden okunan baasınç değerine bağlı olarak da akışkanın doyma sıcaklığı belirlenmiştir. Evaporatördeki ısı güç de, ısıtıcıya sağlanan elektrik enerjisine eşit olduğu için, elde edilen verilerle kaynama ısı taşınım katsayısı hesaplanmıştır. Bu tez kapsamında aseton için yapılan havuz kaynama deneylerinde elde edilen ısı taşınım katsayısı ve Nusselt sayısı değerleri, ilgili deney şarlarında literatürdeki bağıntıların verdiği sonuçlarla karşılaştırılmış ve deneysel sonuçların Cooper ve Ribatski & Jabardo bağıntıları ile yakınsadığı görülmüştür. Deneysel çalışmada elde edilen kaynama ısı taşınım katsayıları farklı basınç değerlerinde elde edildiği için bu tez kapsamında yapılan çalışma sonucunda elde edilen verilere göre bir kaynama ısı taşınım katsayısı ya da Nusselt sayısı bağıntısı önermek doğru olmaz. Ayrıca 3 farklı ısı akısı için de rejim hali olmadan 40 kPa ve 100 kPa basınç değerleri arasında her 10 kPa basınç değişiminde kabarcık oluşumunun nasıl değiştiği görsel olarak incelenmiştir. Basınç ve sıcaklığın artması ile kabarcık boyutlarının küçüldüğü, kabarcık sayısının ise arttığı gözlemlenmiştir.
Özet (Çeviri)
Boiling heat transfer has quite wide usage area for industrial applications. Evaporators, steam boilers, heat pipes are some examples where boiling heat transfer can be seen. Because cost is an important parameter for commercial goods, minimum heat transfer area and maximum heat transfer is the main purpose for a new commercial product design. This purpose makes heat transfer coefficient so significant parameter. Therefore, there are too many studies about boiling heat transfer and enhanced surfaces which provide higher boiling heat transfer coefficient. Although, boiling heat transfer and convection heat transfer have some similarities (like both are occurred between a solid surface and a fluid), due to phase change and molecule movements make boiling heat transfer more complicated. Because boiling has quite complex mechanism, it is not easy to obtain a theoretical correlation as connective heat transfer has. Therefore, usually boiling heat transfer correlations are obtained by experimental studies like convection heat transfer correlations for turbulent flows. An experimental setup, to investigate nucleated pool boiling on horizontal tube, has been designed and built as part of this master thesis. It has been aimed to perform pool boiling experiments on a horizontal tube under different pressure, temperature and heat flux values. Although, pool boiling experiments have been performed for only one tube and one fluid as part of this study, experimental setup has been designed as capable to perform boiling experiments for different type of tubes and fluids. It is know that, pressure is one of the significant parameter for pool boiling. Therefore, experimental setup has been designed to be able to perform boiling experiments for different pressures. Therefore, setup has been designed as a closed loop. Basically, setup designed as an evaporator tank and a condenser tank which connected to each other with two pipes, one pipe connection on top of tanks and another pipe connection at the bottom of tanks. Thus, fluid which evaporates in evaporator tank will go up and move to the condenser tank through connection pipe. Fluid in vapor phase at the condenser will lose heat energy and condense. Condensate fluid will accumulated at the bottom of condenser tank and go back to evaporator tank through connection pipe at the bottom of tanks, regarding combined vessels principle. Evaporator has been design basically as a horizontal cylinder which has a demountable cover on one side to be able to perform experiment on different pipes and welded cover on the other side. Test specimen (pipe) has been assembled on the cover by screwed connection. One side of specimen tube has been closed and other side has been left open to allow heater assembly. In addition, a sight glass has been mounted on the evaporator tank to observe boiling during experiments. Electrical energy has been selected as energy source for boiling. Since, it is more reliable to measure electrical energy which will be provided to specimen pipe to obtain boiling, electrical heater has been preferred. Heater has been designed as helically shape to have homogeneous heat flux on the tube. Selected heater is able to provide 2300 W with 220V. That means, it is possible to have 43000 W/m2 heat flux on the specimen tube which has 33,7 mm diameter. Condenser design includes a helical coil which made of copper located inside a cylindrical tank. Two ends of copper coil have been assembled to a chiller to remove heat from condenser. Copper coil located at the upper side of condenser tank to ensure that liquid phase of fluid level is always stay below the coil. Condenser coil does not work properly if it submerge the liquid phase. In addition a pre-heater which has 2,5 kW power has been added to bottom of condenser tank to heat sub cooled fluid in condenser. To ensure whole power supplied from electrical heater is used for boiling, saturated liquid is needed inside evaporator tank. Otherwise, electrical power will be used first to heat obtain saturated liquid, then boiling. The pre-heater is controlled with a PID controller which gets temperature signal from evaporator via a thermo couple. Because, experimental setup has a closed loop, boiling can be obtained for both negative and positive pressure. A vacuum pump has been implemented to setup to achieve negative pressure in the system. If the power provided from electrical heater in evaporator is equal to power removed from condenser, regime condition is obtained for any pressure or temperature. Regime condition is needed to perform pool boiling experiment and calculate a heat transfer coefficient. To perform pool boiling experiments on designed setup, some auxiliary equipments have been implemented to setup such as a voltage regulator for power supply to specimen tube, a data logger to collect temperature and pressure data and a chiller to remove heat from condenser. Pool boiling experiments have performed for acetone as part of this master thesis for both with regime and without regime condition. Experiments with regime have been performed to calculate a boiling heat transfer coefficient, without regime have been performed to visualization of nucleation on the tube surface. Pool boiling heat transfer coefficient have been calculated by dividing heat flux on specimen tube to excess temperature between surface and saturated liquid. Heat flux calculated by electrical power from main heater which is determined by measuring current and voltage value. Saturation temperature has been determined by measuring pressure via pressure transmitter located on evaporator tank. Surface temperature has been determined by average of temperature measurements for different locations of specimen tube. Surface temperatures have been measured via total 14 pieces thermocouples which located on the top, bottom and side points of tube. Visualization of pool boiling experiments have been performed without regime for 3 different heat flux on stainless steel tube. Pool boiling of acetone have been visualized every 10 kPa pressure change between 40 kPa and 100 kPa pressure. Main purpose of visualization of pool boiling study is understand the effect of pressure and heat flux on nucleation. Experimental pool boiling heat transfer coefficients and Nusselt numbers have been determined for 4 different heat flux values with different saturation pressures. Calculated heat transfer coefficients and Nusselt numbers have been compared to some correlations in literature and seen convergence with Cooper and Ribatski & Jabardo correlations. Because pressure values are different on each regime conditions, it is not proper to propose a heat transfer correlation or Nusselt number correlation regarding experimental results of this thesis study. Nucleated pool boiling of acetone on horizontal tube have been investigated visually for 3 different heat fluxes for different pressure values without regime and seen less nucleate quantity, bigger nucleate size for lower pressures, more nucleate quantity, smaller nucleate size for higher pressure values.
Benzer Tezler
- Computational investigation of pool boiling around different diameter horizontal tubes under atmospheric and sub-atmospheric pressure
Farklı çaplardaki yatay borular üzerinde havuz kaynamanın atmosfer ve atmosfer altı basınçlarda sayısal incelenmesi
SİNAN ÖZBÖLGİLİ
Yüksek Lisans
İngilizce
2024
Makine MühendisliğiGebze Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. GAMZE GEDİZ İLİŞ
- Yatay bir boru içinde FC-72 akışkanının akış kaynamasının düz ve oyuklu bir yüzeyde ve havuz kaynamasının düz bir yüzeyde nümerik olarak incelenmesi
Numerical investigation of single bubble flow boiling both on a flat surface and on a cavity in horizontal pipe and pool boiling on a flat surface
MEHMETCAN DÖNERTAŞ
Yüksek Lisans
Türkçe
2018
Makine MühendisliğiYıldız Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. SEBİHA YILDIZ
- Yer altı drenaj sistemleri hidrodinamiğinin sayısal ve deneysel olarak incelenmesi
Numerical and experimental investigation of hydrodynamic properties of underground drainage systems
KENAN KAYA
Doktora
Türkçe
2019
Makine MühendisliğiYıldız Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. OKTAY ÖZCAN
- Formalization of information requirements for implementing building information modeling based on model uses
Yapı bilgileri modellemesinin model kullanımlarına göre uygulanması için bilgi gereksinimlerinin formalizasyonu
RAIF ALSHORAFA
Doktora
İngilizce
2021
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. ESİN ERGEN PEHLEVAN
- Experimental investigation and modeling of dropwise condensation on a horizontal gold coated tube
Altın kaplı yatay bir boru üzerinde damlacık yoğuşmasının modellenmesi ve deneysel olarak incelenmesi
ORHAN SERDAR
Yüksek Lisans
İngilizce
2004
Makine MühendisliğiOrta Doğu Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. CEMİL YAMALI