Epoxy-based composites and coatings: Improvement of multifunctional properties
Epoksi bazlı kompozitler ve kaplamalar: Çoklu fonksiyonel özelliklerinin geliştirilmesi
- Tez No: 561982
- Danışmanlar: PROF. DR. GÖKNUR BAYRAM, PROF. DR. ÜLKÜ YILMAZER
- Tez Türü: Yüksek Lisans
- Konular: Polimer Bilim ve Teknolojisi, Polymer Science and Technology
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2019
- Dil: İngilizce
- Üniversite: Orta Doğu Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Kimya Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Kimya Mühendisliği Bilim Dalı
- Sayfa Sayısı: 166
Özet
Bu çalışmanın amaçları, genleşmiş grafit (EG) ve titanyum dioksit (T) partikülleri ekleyerek, epoksinin mekanik özelliklerinin, termal stabilitesinin, yanmaya karşı direncinin, elektriksel iletkenliğinin ve hidrofobisitesinin iyileştirilmesidir. Bu çalışmada, öncelikle çözücü kullanımıyla sonikasyon yöntemi epoksi bazlı kompozitlerin ve kaplamaların hazırlanma yöntemi olarak belirlenmiştir. Bu yöntemle, EG konsantrasyonu ağırlıkça %0,05, 0,1, 0,25, 0,5, 0,75 ve 1 olarak ve TiO2 konsantrasyonu ağırlıkça %0,5, 1, 2 ve 5 olarak değiştirilerek epoksi kompozitler ve kaplamalar hazırlanmıştır. Diğer bir taraftan, epoksi bazlı hibrid kompozitlerin ve kaplamaların üretimi için çözücü kullanımıyla sonikasyon yöntemi modifiye edilmiştir ve optimum formülasyonları ikili E/EG ve E/T kompozitlerin mekanik özelliklerine göre kararlaştırılmıştır. Epoksi bazlı kompozitler çekme ve darbe testleri, Shore D sertlik testi, SEM analizi, termal analizler, LOI analizi ve elektriksel direnç testi ile karakterize edilirken, kaplamalara su ile kontak açısı ölçümü ve yüzey enerji analizi uygulanmıştır. Epoksiye ağırlıkça %0,1 EG eklendiğinde, çekme dayanımı, elastisite modülü ve çarpma dayanımı sırasıyla %24, %25 ve %40 artarken, bu konsantrasyonda epoksinin 1014 ohm.cm olan elektriksel özdirenci 109 ohm.cm'ye düşmüştür. Saf epoksinin LOI değeri ağırlıkça %5 TiO2 eklenmesiyle %26'ya çıkmıştır. E/0.05EG/0.5T hibrid kompozit, çekme ve darbe özelliklerinde ikili kompozitlerine kıyasla daha çok iyileşme sağlamıştır.
Özet (Çeviri)
The purposes of this study are to improve mechanical properties, thermal stability, resistance to flammability, electrical conductivity and hydrophobicity of epoxy (E) by incorporation of expanded graphite (EG) and titanium dioxide (T) particles. In this study, sonication with the use of solvent method was primarily determined for the epoxy-based binary composite and coating preparation. By this method, the epoxy composites and coatings were produced by changing EG concentration as 0.05, 0.1, 0.25, 0.5, 0.75 and 1 wt.% and changing TiO2 concentration as 0.5, 1, 2 and 5 wt.%. On the other hand, sonication with the use of solvent method was modified for fabrication of the epoxy-based hybrid composites and coatings, and their optimum formulations were determined based on the mechanical properties of the E/EG and E/T binary composites. The epoxy-based composites were characterized by tensile and impact tests, Shore D hardness test, SEM analysis, thermal analyses, LOI analysis and electrical resistivity test while water contact angle measurement and surface energy analysis were performed on their coatings. The tensile strength, elastic modulus and impact strength of the neat epoxy were increased by 24%, 25% and 40% over the neat epoxy at 0.1 wt.% EG loading while the electrical resistivity was reduced from 1014 to 109 ohm.cm at this concentration. The LOI value of the neat epoxy was increased to 26% by 5 wt.% TiO2 addition. The E/0.05EG/0.5T hybrid composite provided higher enhancement in tensile and impact properties compared to its binary composites.
Benzer Tezler
- Epoksi kaplamalarda farklı katkılar kullanarak elektriksel, termal ve mekanik özelliklerin geliştirilmesi
Improvement of electrical, thermal and mechanical properties of the epoxy coatings by using different additives
FUNDA DENİZ
Yüksek Lisans
Türkçe
2023
Metalurji MühendisliğiDokuz Eylül ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
DOÇ. AYLİN ZİYLAN
- Investigation of mechanical properties of nanoparticle coated glass fiber/epoxy composites coated with dip coating and industrial production methods
Daldırma ve endüstriyel üretim yöntemleri ile üretilmiş nanoparçacık kaplı cam elyaf/epoksi kompozitlerin mekanik özelliklerinin incelenmesi
EMİR ÇETİNALP
Yüksek Lisans
İngilizce
2024
Mühendislik Bilimleriİstanbul Teknik ÜniversitesiNanobilim ve Nanomühendislik Ana Bilim Dalı
DOÇ. DR. BİRGÜL BENLİ
- Modification of polyamide flock fibers and their use in composites
Poliamid flok fiberlerinin modifikasyonu ve kompozitlerde kullanımı
MURAT SAN
Yüksek Lisans
İngilizce
2024
Kimya MühendisliğiOrta Doğu Teknik ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
DOÇ. DR. HARUN KOKU
PROF. DR. BORA MAVİŞ
- Polistirenle modifiye epoksi reçine bazlı nanokompozit ve hibrit kompozitlerin üretimi ve karakterizasyonu
Fabrication and characterization of polystyrene modified epoxy resin based nanocomposite and hybrid composites
NİMET ÖZMERAL
Yüksek Lisans
Türkçe
2023
Kimya MühendisliğiKonya Teknik ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
PROF. DR. GÜLNARE AHMETLİ