Döküm presi ile elde edilen magnezyum alaşımlarının mekanik özelliklerinin belirlenmesi
Determination of mechanical properties of magnesium alloys obtained by casting press
- Tez No: 567619
- Danışmanlar: DOÇ. DR. LEVENT URTEKİN
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2019
- Dil: Türkçe
- Üniversite: Kırşehir Ahi Evran Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İleri Teknolojiler Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 88
Özet
Bu çalışmada, AZ91 Magnezyum alaşımı soğuk kamaralı basınçlı döküm makinesi ile üretilmiştir. ASTM çekme standartlarına uygun kalıplara döküm işlemi farklı parametreler (döküm sıcaklığı, kalıp içi basınç ve yolluk giriş hızı) kullanılarak gerçekleştirilmiştir. Ayrıca geleneksek döküm yöntemi ile de test numuneleri üretilmiştir. Elde edilen numunelerin çekme testi, sertlik testi, aşınma testi ve mikro yapı analizleri yapılmıştır. Ayrıca basınçlı döküm yönteminde döküm işlem parametrelerin mekanik özelliklere etkisi belirlenmiştir Basınçlı döküm ve geleneksel döküm yöntemi ile üretilmiş numunelerin mekanik özellikleri kıyaslanmıştır. İlk ve ikinci numune için 1000 bar ve üçüncü numune için 1200 bar kalıp içi basınç değeri seçilmiştir. Yolluk giriş hızı 30 m/s, 45 m/s ve 45 m/s olarak belirlenmiştir. Sırasıyla 680°C, 680°C ve 640 °C döküm sıcaklığı uygulanarak çekme test numuneleri üretilmiştir. Döküm sıcaklığı ve kalıp içi basıncın sabit kalması ve yolluk giriş hızının 30 m/s den 45 m/s yükseltilmesi tane boyutunda irileşmeye ve mekanik özelliklerde (çekme dayanımı, sertlik değerleri ve aşınma direncinde) azalmaya sebep olmuştur. Döküm sıcaklığının 640 °C düşürülmesi ve kalıp içi basıncın 1200 Bar'a yükseltilmesi geleneksel döküm yöntemine yakın mukavemet değerleri elde edilmiştir. Aşınma testlerinde, basınçlı döküm yöntemi ile üretilmiş numunenin sertlik değerlerindeki artışla beraber sürtünme katsayısında azalmanın olduğu ve malzeme kaybının olmadığı gözlemlenmiştir. Geleneksel döküm yönteminde soğuma hızı, basınçlı döküm yöntemine göre yavaş olduğundan, basınçlı döküm yönteminde ince taneli yapı oluşması ile yüksek mekanik özellikler elde edilmiştir. Deneysel sonuçlar, çizelgeler halinde deneysel bulgular bölümünde verilmiştir.
Özet (Çeviri)
In this study, AZ91 Magnesium alloy is produced by cold chamber die casting machine. The casting process was carried out using different parameters (casting temperature, in-mold pressure and gating input speed). In addition, test samples were produced by conventional casting method. Tensile test, hardness test, abrasion test and microstructure analysis of samples were performed. In addition, the effect of casting process parameters on the mechanical properties was determined in the pressure casting method. The mechanical properties of the samples produced by pressure casting and traditional casting method were compared. In-mold pressure values of 1000 bar for the first and second samples and 1200 bar for the third sample were selected. Runway entry speed is determined as 30 m / s, 45 m / s and 45 m / s. Tensile test specimens were produced by applying casting temperatures of 680 ° C, 680 ° C and 640 ° C respectively. The casting temperature and in-mold pressure remained constant and the runner entry speed increased from 30 m / s to 45 m / s, resulting in coarse grain size and reduced mechanical properties (tensile strength, hardness values and wear resistance). Decreasing the casting temperature by 640 ° C and increasing the in-mold pressure to 1200 Bar strength values were obtained close to the traditional casting method. In abrasion tests, it was observed that there was a decrease in friction coefficient and no loss of material with the increase of hardness values of the sample produced by pressure casting method. Since the cooling rate in the traditional casting method is slower than that of the pressure casting method, high mechanical properties are obtained by the formation of fine-grained structure in the pressure casting method. Experimental results are given in the experimental findings section.
Benzer Tezler
- Farklı alaşım elementi ilaveli WE43 magnezyum alaşımlarının döküm ve ekstrüzyon sonrası mikroyapı, mekanik ve korozyon özelliklerinin incelenmesi
Investigation of microstructure, mechanical and corrosion properties of the as-cast and as-extruded we series of the magnesium alloys containing different alloying elements
YASİN SUBAŞI
Doktora
Türkçe
2020
Metalurji MühendisliğiKarabük ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
DOÇ. DR. YUNUS TÜREN
- Mekanik alaşımlama yöntemleri ile üretilmiş Al15Si2,5Cu0,5Mg matriksli ve CeO2, Y2O3, La2O3 pekiştiricili kompozitlerin geliştirilmesi ve karakterizasyonu
Development and characterization of Al15Si2,5Cu0,5Mg matriksli ve CeO2, Y2O3, La2O3 reinforced composites synthesized by mechanical alloying
EMRE TEKOĞLU
Yüksek Lisans
Türkçe
2015
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA LUTFİ ÖVEÇOĞLU
- Sıcak presleme yöntemi ile Al2Cu ve h-BN katkılı alüminyum ve alüminyum alaşım matrisli kompozitlerin aşınma davranışlarının incelenmesi
Investigation of abrasion behavior of aluminum and aluminum alloy reinforced with Al2Cu and h-BN produced by hot pressing
BURAK SAMED DOĞU
Yüksek Lisans
Türkçe
2020
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. HÜSEYİN ÇİMENOĞLU
- Sentezlenen ve ticari LaB6 katkılı mekanik alaşımlanmış Al-Ağ.%7si toz ve sinter hibrit kompozitlerin geliştirilmesi ve karakterizasyonu çalışmaları
Development and characterization investigations of labratory synthesized and commercial LaB6 reinforced Al-7% wt. Si powders and sintered hybride composites
SIDDIKA MERTDİNÇ
Yüksek Lisans
Türkçe
2016
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMalzeme Bilimi ve Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA LUTFİ ÖVEÇOĞLU
- Alüminyum matrisli insitu kompozitlerin üretilmesi ve yarı katı şekillendirilmesi
Production and semi-solid forming of aluminium matrix in situ composites
TOLGA ÖZKAN
Yüksek Lisans
Türkçe
2023
Metalurji MühendisliğiYıldız Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. KEREM ALTUĞ GÜLER