Geri Dön

Dönü kararlı hafif kalibre mermiler için balistik katsayıların deneysel olarak hesaplanması ve doğrulanması

Experimental calculation and verification for the ballistic coefficients of small caliber spin stabilized projectiles

  1. Tez No: 590536
  2. Yazar: İHTİMAM MERT VARDAR
  3. Danışmanlar: ÖĞR. GÖR. YAVUZ ZÜMRÜT
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2019
  8. Dil: Türkçe
  9. Üniversite: Gazi Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 132

Özet

Balistik katsayı, referans mermi geometrilerine göre belirlenmekte olup dönü kararlı merminin hava direncinden ne oranda etkilendiğinin ve aerodinamik performansının iyi bir ölçütüdür. Dönü kararlı merminin balistik katsayı değeri, merminin yörüngesi boyunca Mach Sayısı cinsinden değişen hızına bağlı olarak değişmesine rağmen, mermi üreticisi firmalar tüm yörünge için genellikle tek bir balistik katsayı değeri yayımlamaktadırlar. Diğer taraftan, referans mermi geometrisinin ele alınan mermiyi yüksek bir doğrulukla temsil edememe durumu mevcut ise, tek bir balistik katsayı değeri ile mermi yörüngesinin tamamının yeterli doğrulukla temsil edilemeyeceği de bilinmektedir. Bunun sonucu olarak, bilhassa uzun menzil atışlarında yeterli isabetin sağlanamaması problemi ortaya çıkmaktadır. Bu çalışmada, bir 7,62 mm kalibre dönü kararlı hafif silah mermisinin Mach Sayısı cinsinden hızına bağlı olarak değişen sürüklenme katsayıları doppler radarı kullanılarak ölçülmüştür. Elde edilen verilerden, ele alınan mermi için G1 referans mermisine göre etkili menzilinin tamamını temsil edebilecek çoklu balistik katsayılar ve G7 referans mermisine göre de tek bir balistik katsayı değeri hesaplanmıştır. Hem çalışmada hesaplanan balistik katsayı değerlerine, hem de üreticinin G1 referans mermisine göre yayımladığı balistik katsayı değerine göre Quick Target yazılımı yardımıyla balistik tablolar hazırlanmıştır. Elde edilen bu balistik tablolara göre yapılan 300, 550, 700 ve 800 metre mesafe atışlı performans testlerinin sonuçları karşılaştırılmıştır. Bu çalışma ile bilhassa referans mermi geometrisinin ele alınan mermiyi yeterince doğru bir biçimde temsil edemediği durumda çoklu balistik katsayı değerleri ile, referans mermi geometrisinin ele alınan mermiyi yeterince doğru bir biçimde temsil ettiği durumda ise tek bir balistik katsayı değeri ile, mermi yörüngesi etkili menzil boyunca kabul edilebilir bir hata oranı ile belirlenmiştir.

Özet (Çeviri)

The ballistic coefficient of a spin-stabilized bullet can be determined with respect to a reference model and it is a good measure of spin-stabilized bullet's aerodynamic performance and extent to which bullet is affected from air drag. Even though the ballistic coefficient value for the bullet of spin-stabilized small caliber ammunition varies according to the change in the speed of bullet in terms of Mach number throghout the trajectory, the manufacturer firms issue a single mean ballistic coefficient value for the entire trajectory. On the other hand, in case of the reference bullet geometry can not represent the given bullet well enough, it is known that the entire bullet trajectory can not be represented accurately with a single mean ballistic coefficient value. As a result of this issue, insufficient hit problem occurs especially at long range shooting. In the present study, drag coefficient values, which change depending on the speed in terms of Mach Number, were measured by using doppler radar for the spin-stabilized bullet of 7,62 mm caliber ammunition. Based on the data obtained from these measurements, multiple ballistic coefficient values according to the G1 reference bullet and a single mean ballistic coefficient value according to the G7 reference bullet, which represent the entire effective firing range of the investigated bullet, were calculated for the investigated bullet. Ballistic tables were prepared by using Quick Target software according to both calculated ballistic coefficients in this study and the ballistic coefficient value which were issued by manufacturer for the G1 reference bullet. Results of the shooting performance tests, which were carried out to 300, 550, 700 and 800 meters distances according to these ballistic tables, were compared with each other. With this study, bullet trajectory was determined over the effective firing range with an acceptable error rate with multiple ballistic coefficient values, especially in case where the reference bullet geometry can not represent the investigated bullet accurately, and with a single ballistic coefficient value when the reference bullet geometry can represent the investigated bullet accurately.

Benzer Tezler

  1. Realtime magnetometer calibration for spinning aerospace vehicles

    Hava araçları için gerçek zamanlı manyetometre kalibrasyonu

    MUSTAFA EFE ÇETİN

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Mühendislik BilimleriOrta Doğu Teknik Üniversitesi

    Havacılık ve Uzay Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ HALİL ERSİN SÖKEN

    PROF. DR. OZAN TEKİNALP

  2. Dönü kararlı mermilerin aerodinamik katsayıları, kararlılık özellikleri ve yörünge hesaplamaları

    Calculation of aerodynamic coefficients, stability properties and trajectory of spin-stabilized projectiles

    ERKAN TİRYAKİ

    Yüksek Lisans

    Türkçe

    Türkçe

    2009

    Fizik ve Fizik MühendisliğiAnkara Üniversitesi

    Fizik Mühendisliği Ana Bilim Dalı

    DOÇ. DR. MEHMET KABAK

  3. Design and control of nose actuation kit for position correction of spin stabilized munitions under wind effect

    Dönü kararlı mühimmatların rüzgar etkisi altında konum düzeltmesini sağlayacak bir burun tahrik sisteminin tasarımı ve kontrolü

    MESUT EROĞLU

    Yüksek Lisans

    İngilizce

    İngilizce

    2016

    Havacılık MühendisliğiOrta Doğu Teknik Üniversitesi

    Havacılık ve Uzay Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. ALİ TÜRKER KUTAY

  4. Controller design and implementation for a guidance kit used at spinning rockets and projectiles

    Dönen roket ve mühimmatlarda kullanılan bir güdüm kiti için kontrolcü tasarımı ve uygulanması

    GÖRKEM GÜNAY

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Makine MühendisliğiOrta Doğu Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. RAİF TUNA BALKAN

    DR. ÖĞR. ÜYESİ HAKAN ÇALIŞKAN

  5. Dynamic simulation of an indirect partial oxidation reactor for methane conversion to hydrogen

    Metan gazının dolaylı kısmi oksidasyon reaktöründe hidrojene dönüşümünün dinamik benzetimi

    MUSTAFA KARAKAYA

    Yüksek Lisans

    İngilizce

    İngilizce

    2006

    EnerjiBoğaziçi Üniversitesi

    Kimya Mühendisliği Ana Bilim Dalı

    DOÇ.DR. AHMET ERHAN AKSOYLU

    PROF.DR. ZEYNEP İLSEN ÖNSAN