Karbürleme yapılan genel yapı çeliğinin mikroyapı ve mekanik özelliklerinin incelenmesi
Investigation of microstructural and mechanical properties of carburized general construction steel
- Tez No: 676106
- Danışmanlar: PROF. DR. KHANGARDASH ASGAROV
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2021
- Dil: Türkçe
- Üniversite: Karabük Üniversitesi
- Enstitü: Lisansüstü Eğitim Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 85
Özet
Bu çalışmada, yapı çeliği olarak bilinen alaşımsız St37 çeliğinden üretilmiş numunelere kutu karbürleme (sementasyon) işlemi uygulanarak yüzey sertleştirmenin mikroyapı ve mekanik özelliklerine etkisi incelenmiştir. Deneyde 800 ºC ve 930 ºC 'deki 2 farklı sıcaklıklarda gerçekleşen numuneler kutu içerisinde kömür tozu ile birlikte ağzı sıkıca hava almayacak şekilde kapatılarak 3,5 ve 10 saat sementasyon olacak şekilde fırında bekletilmiştir. Sementasyon yapılan numunelerin mikroyapısı incelenerek kaplama kalınlıkları, sertlik deneyleri yapılarak sertlik değişimleri ve aşınma deneyleri yapılarakta aşınma miktarları incelenmiştir. Yapılan vickers yöntemi sertlik testleri sonucunda, en yüksek sertlik değerleri 930 ºC ve 10 saat sementasyon yapılan numunede olduğu ortaya çıkmıştır. Aşınma testleri sonucunda numuneye 10N ve 20N luk yükler verilerek malzemenin üzerindeki aşınma cihazının 10 mm strok mesafede 100 m yol alarak aşınma miktarları bulunmuştur. Aşınma testleri sonucunda uygulanan sementasyon süresi ile aşınma kaybının ters orantılı olduğu, aynı şekilde sementasyon sıcaklık değeri ile aşınma kaybıda ters orantılı iken uygulan yük ile aşınma kaybının doğru orantılı olduğu tespit edilmiştir.
Özet (Çeviri)
In this study, the effect of surface hardening on microstructure and mechanical properties was investigated by applying box carburizing (cementation) process to samples produced from unalloyed St37 steel, known as structural steel. In the experiment, the samples, which took place at 2 different temperatures at 800 ºC and 930 ºC, were kept in the oven with coal dust in the box for 3, 5 and 10 hours for cementation, with the mouth tightly closed. By examining the microstructure of the cemented samples, the coating thicknesses, hardness changes by making hardness tests, and the amount of wear were examined by performing abrasion tests. As a result of the vickers method hardness tests, it was revealed that the highest hardness values were found in the sample that was cemented for 10 hours at 930 ºC. As a result of the wear tests, 10N and 20N loads were applied to the sample, and the wear amount of the wear device on the material was found by traveling 100 m at a stroke distance of 10 mm. As a result of the wear tests, the applied cementation time and the wear loss are inversely proportional, while the cementation temperature value is inversely proportional to the wear loss. It has been determined that the applied load and the wear loss are directly proportional.
Benzer Tezler
- AISI D2 soğuk iş takım çeliklerinin darbeli kayma aşınma davranışına mikroyapının etkisi
The effect of microstructure on impact sliding wear behavior of AISI D2 cold work tool steels
HALİL İBRAHİM FİLİZ
Yüksek Lisans
Türkçe
2021
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. MURAT BAYDOĞAN
- Östenitik paslanmaz çeliğin bor katkılı Ni3Al ile kaplanabilirliğinin araştırılması
Investigation of boron doped Ni3Al coating of austenitic stainless stell
MEHMET AKKAŞ
Yüksek Lisans
Türkçe
2013
Metalurji MühendisliğiFırat ÜniversitesiMetalurji Eğitimi Ana Bilim Dalı
DOÇ. DR. SERMİN OZAN
- CrCoNi süperalaşımının yüksek sıcaklık oksidasyon ve karbürizasyon davranışı
The High temperature oxidation and carburization behavior of CrCoNi super alloys
EMRAH FAHRİ ÖZDOĞRU
Yüksek Lisans
Türkçe
2002
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji Mühendisliği Ana Bilim Dalı
PROF. DR. E. SABRİ KAYALI
- Düşük kromlu çeliklerde kobalt miktarının mikroyapıya ve tokluğa etkisi
Effect of cobalt content on microstructure and toughness of low chromium steels
GÖKHAN ARICI
Doktora
Türkçe
2019
Metalurji MühendisliğiSelçuk ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. MESUT UYANER
PROF. DR. MUSTAFA ACARER
- Beyaz dökme demirden üretilen maden kırıcılarında molibdenin mikroyapıya ve mekanik özelliklere etkisi
Effect of molybdenum on mechanical properties and microstructure of white cast iron for mining application
HAKAN YILDIRIM
Yüksek Lisans
Türkçe
2014
Makine MühendisliğiHitit ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. KAMİL ÖZDİN