Tool wearandchip deformation incutting difficult-to-cutplastic composites
Başlık çevirisi mevcut değil.
- Tez No: 718281
- Danışmanlar: PROF. KATSUMI YAMAGUCHI
- Tez Türü: Doktora
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 1997
- Dil: İngilizce
- Üniversite: Nagoya University
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 192
Özet
Özet yok.
Özet (Çeviri)
This dissertation was submitted in partially fulfillment of the requirements for the degree of Ph.D. of engineering in department of mechanical engineering in Nagoya University. Cutting phenomenon and tool wear in cutting composite materials are somewhat different from those in cutting of homogenous materials. The literature concerning cutting of composite materials is still insufficient for comprehensive knowledge of cutting processes of many composites. This research concerns the cutting of two types of plastic composite materials; one is SiC whisker-reinforced plastic (SiCw-RP) and the other is aramid-glass hybrid fibers-reinforced plastic (A-GFRP) composites. These two composites are difficult-to-cut materials. This is because SiC whisker is extremely hard and stiff material in case of SiCw-RP. For A-GFRP composite, aramid fiber is strong and stiff fiber but soft and weak against compression, hence it is very difficult to cut this fiber sharply. The dissertation is divided into 8 chapters numbered consecutively. Chapter 1 introduces the composite materials. Chapters 2 to 5 concern SiC whisker-reinforced plastic composite. Chapter 6 and 7 concems aramid-glass hybrid fibers-reinforced plastic. Finally, chapter 8 includes the conclusions of this research work. Chapter 1 includes the definition of the term of composite material, classification of composites and the constituents of composite and their characteristics. Moreover, the composites concemed in this dissertation are introduced and the difficulties in cutting of some composites are reviewed from the literature. Finally, the objectives and the outline of this research are summarized.
Benzer Tezler
- Tarihî Türk yazı dillerinde alet isimleri
Tool names in historical Turkish written languages
GÖKBERK ONARAN
Yüksek Lisans
Türkçe
2024
Türk Dili ve EdebiyatıMardin Artuklu ÜniversitesiTürk Dili ve Edebiyatı Ana Bilim Dalı
DOÇ. DR. SERDAL KARA
- İlk aşınma bölgesinde takım aşınmasını etkileyen parametrelerin deneysel analizi
Experimental analyse of parameters effects on tool wear in the initial tool wear region
KADİR ÖZDEMİR
Yüksek Lisans
Türkçe
2008
Makine MühendisliğiUludağ ÜniversitesiMakine Mühendisliği Bölümü
PROF. DR. M. CEMAL ÇAKIR
- Takım çeliklerinin termoreaktif difüzyon yöntemiyle vanadyum karbür kaplanması
Vanadium carbide coatings on tool steels by thermoreactive diffusion process
ZERRİN ÖKTEM
Doktora
Türkçe
1997
Makine MühendisliğiKocaeli ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. LEVON ÇAPAN
- Tool path optimization of free form surfaces
Serbest biçim yüzeylerde takım yolu eniyilemesi
AHMET CANBERK MANAV
Yüksek Lisans
İngilizce
2009
Makine MühendisliğiKoç ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. İSMAİL LAZOGLU
- Termo- kimyasal yöntemle kaplanmış farklı kesici takım malzemelerinin talaşlı işlem kabiliyetinin incelenmesi
Machining behavior of thermo-chemicaly cooted different cutting tool matherials
ŞENOL ERTÜRK
Yüksek Lisans
Türkçe
2010
Makine MühendisliğiSakarya ÜniversitesiMakine Eğitimi Ana Bilim Dalı
YRD. DOÇ. SAKIP KÖKSAL