Konveyörlü bir kurutucuda farklı geometrik şekillere sahip gözenekli yapıların kurutma kinetiğinin sayısal analizi
Numerical analysis of drying kinetics of porous structures with different geometric shapes in a conveyor dryer
- Tez No: 757874
- Danışmanlar: DOÇ. FATİH SELİMEFENDİGİL
- Tez Türü: Doktora
- Konular: Enerji, Makine Mühendisliği, Mühendislik Bilimleri, Energy, Mechanical Engineering, Engineering Sciences
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2022
- Dil: Türkçe
- Üniversite: Manisa Celal Bayar Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Termodinamik ve Isı Bilim Dalı
- Sayfa Sayısı: 308
Özet
Bu çalışmada konveyörlü bir kurutucuda sıcak havayla kurutma işleminin sayısal analizi ile ilgili birçok çalışma gerçekleştirilmiş, çalışmalar aşama aşama geliştirilerek kurutma prosesindeki farklı parametrelerin kurutma performansına olan etkileri incelenmiştir. Kurutulan cisimler olarak gıda ürünleri, özellikle sebze ve meyve ürünleri tercih edilmiş, ürünlerin özellikleri ise daha önce gerçekleştirilmiş olan deneysel çalışmalardan alınmıştır. Sayısal çalışmalar iki boyutlu ve üç boyutlu olarak nemli cisimlerin durağan ve hareketli durumları için ele alınmıştır. Zamana bağlı kanal akışında ve gözenekli cisim içinde bütünleşik ısı ve kütle transferi problemi için iki boyutlu ve üç boyutlu durumlarda konvektif kurutma performansı için optimizasyon çalışmaları yapılmıştır. İlk olarak, iki boyutlu laminer akış koşullarında kanal içerisinde sabit durumdaki nemli gözenekli dikdörtgen şeklindeki cisim ele alınmış, belli kurutma süresi içerisinde farklı kurutma koşulları altında cisim içerisindeki nem kaybının zamanla değişimi gözlenmiştir. Burada değişken parametreler olarak kurutma havası giriş hızı ve sıcaklığı ele alınmıştır. Kurutma işleminin ilk evrelerinde cismin dış yüzeylerinden olan ve özellikle köşelerden olan nem kaybının maksimum düzeyde olduğu görülmüştür. Ayrıca, kanal hava akış yönüne göre ön kısımda kalan yüzey kurutmada nem kaybının en çok yaşandığı yüzey olmuştur. Kurutma havası hızı ve sıcaklığı değerlerinin her ikisinin de artması nem kaybında artışa sebep olmuştur. Çalışmada, kanal içerisine akışı etkileyen döner bir silindir eklenmiş kurutma üzerinde farklı parametrelerle olan etkisi incelenmiştir. Bu çalışmada, döner cismin büyüklüğünün, dönüş yönünün ve kanal içerisindeki konumunun akışı ve kurutma performansını etkilediği görülmüştür. Dairesel cismin dönüş yönüne bağlı olarak kurutulan cismin farklı yüzeylerinde nem kaybı miktarları değişmiştir. Ayrıca silindirin kanal içerisinde kurutulan cisme olan uzaklığı arttıkça kurutmaya etkisi de azalmış, aynı etki silindir küçüldükçe de azalmıştır. Bundan sonra üç boyutlu kanal içerisinde biden fazla kübik cismin kurutulması ele alınmış, cisimlerin birbiri ile arasındaki mesafe ve kanaldaki yerleşim şeklinin etkileri incelenmiştir. Burada da cisimler arası mesafenin artışı ile arkadaki cisimlerdeki nem kaybının fazlalaştığı görülmüştür. Sonraki çalışmalarda, iki boyutlu kanalda cisme hareket eklenmiş ve cismin kurutma kanalı içerisindeki hareketinin de etkisi hava hızı ve sıcaklığının etkisi ile birlikte incelenmiştir. Aynı etki bir sonraki çalışmada üç boyutlu kanal içerisindeki cisimler için de incelenmiştir. Cisme hareket kazandırmanın kurutma performansı üzerinde olumsuz bir etkisi görülmemiştir. Farklı şekilli cisimlerin kurutma performansının incelendiği çalışmada, daire, kare ve üçgen şeklindeki cisimlerin kurutulması sayısal olarak incelenmiştir. Bu çalışmada da özellikle dairesel şeklin kurutulma işleminde daha iyi sonuçlar verdiği görülmüştür. Aynı çalışmada bu şekil için farklı malzeme özellikleri ile kurutma işlemi incelenmiş, her malzemenin kurutma performansı ortaya konmuştur. Kanal içerisinde farklı kombinasyonlarla kanala yerleştirilen iki eş kare cismin kurutulmasının sayısal olarak incelendiği bir başka çalışmada, cisimler üzerinden olan ısı transferini maksimuma çıkaracak yerleşimi bulmak için bir optimizasyon çalışması yapılmış, kanaldaki cisimlerin birbirlerine olan optimum yatay ve dikey mesafeler elde edilmiştir. Daha sonra kütle transferleri de farklı parametrelerde incelenmiş, maksimum kütle transferinin de optimum aralık değerlerinde olduğu görülmüştür. Benzer bir çalışma daha sonra üç boyutlu kanalda üç kübik eş cisim için yapılmış, kütle transferinin maksimum değeri optimum aralıklarda elde edilmiştir. Optimizasyon çalışmalarında Yapay Sinir Ağları (YSA/ANN) ve Uygun Ortagonal Ayrıklaştırma (UOA/POD) yöntemleri kullanılmıştır. Tez kapsamında yapılan sayısal çalışmalardan elde edilen sonuçlar konvektif kurutmada farklı durumlar için (üç boyutlu kanal, çok sayıda nemli cisim, nemli-gözenekli cisimlerin hareket halinde olması, kanal içinde türbülanslı akış koşulları vb.) etkin parametrelerin kurutma performansına etkisinin ortaya konulmasında ve sonra yapılacak olan deneysel ve sayısal çalışmalarda referans olarak kullanılabilir. Özellikle bu çalışma kapsamında geliştirilen optimizasyon çalışmaları, zamana bağlı üç boyutlu hem kanal içinde hem de gözenekli cisim içinde bütünleşik ısı-akış ve kütle transferi probleminin çözümünde büyük avantaj sağlamakta ve çok sayıda cismin yer aldığı büyük ölçekteki kurutma sistemlerinin modellenmesinde simülasyon zamanını önemli ölçüde kısaltmaktadır.
Özet (Çeviri)
In this study, various studies were carried out on the numerical analysis of the hot air-drying process in a conveyor dryer, the studies were developed step by step and the effects of different parameters in the drying process on the drying performance were examined. Food products, especially vegetable and fruit products, were preferred as dried objects, and the properties of the products were taken from previous experimental studies. Numerical studies are discussed for the stationary and moving states of moist bodies in two dimensions and three dimensions. Optimization studies have been carried out for convective drying performance in two-dimensional and three-dimensional cases for the problem of integrated heat and mass transfer in time-dependent channel flow and porous body. First, the moist porous rectangular-shaped body in the stationary state in the channel under two-dimensional laminar flow conditions was considered, and the variation of moisture loss in the body with time was observed under different drying conditions within a certain drying time. Here, drying air inlet speed and temperature are considered as variable parameters. In the first stages of the drying process, it was observed that the moisture loss from the outer surfaces of the object and especially from the corners was at the maximum level. In addition, the surface in front of the duct air flow direction was the surface where the most moisture loss was experienced during drying. The increase in both drying air velocity and temperature values caused an increase in moisture loss. In the same study, the effect of different parameters on drying with a rotating cylinder that affects the flow into the channel was investigated. It was observed that the size of the rotating body, the direction of rotation and its position in the channel affect the flow and drying performance. Depending on the rotation direction of the circular object, the amount of moisture loss on different surfaces of the dried object changed. In addition, as the distance of the cylinder to the object being dried in the channel increases, its effect on drying decreases, and the same effect decreases as the cylinder gets smaller. After that, the drying of more than one cubic object in the three-dimensional channel was discussed, and the effects of the distance between the objects and the placement in the channel were examined. Here, too, it was observed that the moisture loss in the objects behind increased with the increase in the distance between the objects. In the following studies, motion was added to the object in the two-dimensional duct and the effect of the motion of the object in the drying duct was examined together with the effect of air velocity and temperature. The same effect was investigated for the objects in the three-dimensional channel in the next study. There was no negative effect of adding motion to the object on the drying performance. In the study in which the drying performance of different shaped objects was examined, the drying of circle, square and triangular objects was examined numerically. In this study, it was observed that especially the circular shape gave better results in the drying process. In the same study, the drying process with different material properties for this shape was examined, and the drying performance of each material was revealed. In another study, in which the drying of two equi-square objects placed in the channel with different combinations in the channel was examined numerically, an optimization study was carried out to find the placement that will maximize the heat transfer over the objects, and the optimum horizontal and vertical distances of the objects in the channel to each other were obtained. Then, mass transfers were also examined in different parameters, and it was seen that the maximum mass transfer was within the optimum range values. A similar study was then carried out for three cubic congruent bodies in a three-dimensional channel, and the maximum value of mass transfer was obtained at optimum intervals. Artificial Neural Networks (ANN) and Appropriate Orthogonal Discretization (POD) methods were used in the optimization studies. The results obtained from the numerical studies carried out within the scope of the thesis are to reveal the effect of effective parameters on the drying performance for different situations (three-dimensional channel, many moist objects, moist-porous objects in motion, turbulent flow conditions in the channel, etc.) in convective drying. It can be used as a reference in experimental and numerical studies. In particular, the optimization studies developed within the scope of this study provide a great advantage in solving the problem of integrated heat-flow and mass transfer both in the channel and in the porous body, and significantly shorten the simulation time in modeling large-scale drying systems in which many bodies are involved.
Benzer Tezler
- Helezon konveyör tipi kurutucuda odun parçacıklarının kurutulmasının deneysel olarak incelenmesi
Experimental investigation of drying of woodchips in a screw conveyor dryer
ÖZGÜR KAPLAN
Yüksek Lisans
Türkçe
2012
Makine MühendisliğiKocaeli ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. CENK ÇELİK
- Güneş enerjili hibrit tip bir kurutma sistem tasarımı ve deneysel analizi
Design and experimental analysis of a solar hybrid type drying system
HAMİT BOLOĞUR
Yüksek Lisans
Türkçe
2014
Makine MühendisliğiHarran ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. HÜSAMETTİN BULUT
- Bir mobilya fabrikasında süreç analizi ve süreç iyileştirme
Process analysis and process improvement in a furniture factory
VELİ ÇELİK
Yüksek Lisans
Türkçe
2023
Ağaç İşleriBursa Teknik ÜniversitesiOrman Endüstri Mühendisliği Ana Bilim Dalı
DOÇ. DR. MUHAMMED SAİD FİDAN
- Akışkan yatakta fındık kavurma işleminin deneysel ve teorik incelenmesi
Experimental and theoretical analyses of hazelnut roasting process in fluidized bed dryer
MÜKRİMİN ŞEVKET GÜNEY
Doktora
Türkçe
2007
EnerjiSakarya ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF.DR. MESUT GÜR
Y.DOÇ.DR. İMDAT TAYMAZ
- Doğal gazlı sürekli ısıl işlem fırınlarında brülör tasarımı, imalatı ve baca gazı analizleriyle doğal gaz tüketiminin optimizasyonu
Burner designing and manufacturing in natural gas, continuous heat treatment furnaces and optimization of natural gas consumption by flue gas analysis
SERDAR İSKENDER
Doktora
Türkçe
2012
Makine MühendisliğiGazi ÜniversitesiMakine Eğitimi Ana Bilim Dalı
PROF. DR. H. MEHMET ŞAHİN