Geri Dön

Error analysis and characterization of piezoresistive array touch sensors

Piezodirençli sıra dizilimli dokunma algılayıcılarının hata analizi ve karakterizasyonu

  1. Tez No: 770303
  2. Yazar: MEHMET OGÜN SARP
  3. Danışmanlar: DR. ÖĞR. ÜYESİ KEREM ALTUN
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2022
  8. Dil: İngilizce
  9. Üniversite: İzmir Yüksek Teknoloji Enstitüsü
  10. Enstitü: Lisansüstü Eğitim Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 124

Özet

Çok sayıda araştırma ve akademik çalışma, piezorezistif sensör türlerini içermektedir. Bu tezin temel dayanaklarından biri, detaylı bir hata analizi yaparak ve yeni bir hata azaltma önerisinde bulunarak literatüre katkıda bulunmaktır. Bu tezde, piezorezistif dokunmatik sensörler, piyasada bulunan sensörlerin çalışma prensibine uygun olarak sıfırdan tasarlanmış ve üretilmiştir. Bu tez, tek dokunuşlu uygulamalar için iki farklı sensör konfigürasyonunu incelemektedir. Bu sensörlerde, sensör üzerinde bulunan aynı 61 test noktası, bir seferde tek bir yük olmak üzere toplamda üç farklı yük altında statik olarak test edilmiş, bu noktaların basınç merkezi sonuçları incelenmiş ve birbirleriyle karşılaştırılmıştır. Sonuç olarak 7x7 sensör dizisinin aynı test noktalarında 5x5 sensör dizisinden daha başarılı sonuçlar verdiği gözlemlenmektedir. Kadane algoritması, sensörlerdeki hata değerlerini azaltma amacıyla deney verilerine uygulanmıştır. Sonuç olarak, başarı elde edilmiştir ve hataların azaldığı gözlemlenmiştir. Ayrıca önerilen bir başka yöntem olan daire uydurma ile ölçümlerle oluşan teorik çemberin merkezleri bulunarak sensör ölçümlerinin homojen olarak kabul edilip edilmediği incelenir. Başka bir deyişle, her durumda, merkezden kaçıklık seviyelerinin çok fazla değişmediği deneyimlenmiştir. Son olarak, rastgele seçilen ölçüm noktalarından elde edilen sistem denklemleri üzerinden çok değişkenli doğrusal regresyon yöntemi incelenmiştir. Hem sistem üzerindeki diğer noktaların sensör çıkışlarının tahmin edilebildiği hem de sistem üzerindeki hata metriklerinin azaltılabildiği görülmektedir.

Özet (Çeviri)

Numerous investigations and academic studies employ piezoresistive types of sensors. One of the main foundations of this thesis is to contribute to the literature by making a detailed error analysis and by proposing a new error reduction. In this thesis, piezoresistive touch sensors are designed and manufactured from scratch in accordance with the working principle of commercially available sensors. This thesis examines two different sensor configurations for single-touch applications. On these sensors, three different loads are tested statically with the same 61 test points located on the sensor, a single load at a time, and their Center of Pressure results are examined and compared to each other. As a result, it is observed that the 7x7 sensor array gives more successful results than the 5x5 sensor array at the same test points. Kadane's algorithm is introduced and implemented in experiments aimed to reduce the error values. As a result, success is achieved. Furthermore, with another proposed method, circle fitting, the centers of the theoretical circle formed by measurements are found, and it is examined whether the sensor measurements were considered as homogeneous. In other words, in each case, the levels of decentralization did not vary much. Finally, the multivariate linear regression method is examined through the system equations obtained from the randomly selected measurement points. It is seen that both the sensor outputs of the other points on the system can be predicted and the error metrics on the system can be reduced.

Benzer Tezler

  1. Stiren ile N-izopropilakrilamit ve glisidilmetakrilat'ın kopolimerlerinin sentezi ve karakterizasyonu

    Synthesis and characterization of styrene with N-izopropylacrylami̇de and glycidyl methacriylate copolymers

    LÜTFÜ BULUT

    Yüksek Lisans

    Türkçe

    Türkçe

    2014

    KimyaBozok Üniversitesi

    Kimya Ana Bilim Dalı

    PROF. DR. CENGİZ SOYKAN

  2. Noise analysis in WDM optical fiber communication systems

    Dalgaboyu bölmeli çoğullamalı fiber optik iletişim sistemlerinde gürültü analizi

    MEHMET AKGÜL

    Yüksek Lisans

    İngilizce

    İngilizce

    2009

    Elektrik ve Elektronik MühendisliğiKoç Üniversitesi

    Elektrik ve Bilgisayar Mühendisliği Ana Bilim Dalı

    DOÇ. DR. ALPER DEMİR

  3. CeO2-TiO2(CeO2-ZrO2) ince filmlerinin oluşturulması, optik yapısal ve bazı elektrokimyasal özelliklerinin incelenmesi

    Preparation and investigation of optical, structural and some electrochemical properties of CeO2-TiO2(CeO2-ZrO2) thin films

    FARHAD E GHODSİ

    Doktora

    Türkçe

    Türkçe

    1999

    Fizik ve Fizik Mühendisliğiİstanbul Teknik Üniversitesi

    DOÇ.DR. FATMA Z. TEPEHAN

  4. Türkiye'de atık karakterizasyonu metodolojisi için temel kriterlerin belirlenmesi

    Başlık çevirisi yok

    EDA YAĞCILAR

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Çevre Mühendisliğiİstanbul Teknik Üniversitesi

    Çevre Mühendisliği Ana Bilim Dalı

    PROF. DR. OSMAN ATİLLA ARIKAN

  5. Poli(anilin-ko-tiyofen) kopolimerinin adsorpsiyon özelliklerinin incelenmesi ve yüzey karakterizasyonu

    Investigation of adsorption properties and surface characterization of poly(aniline-co-thiophene) copolymer

    SABRİ CAN KARADENİZ

    Yüksek Lisans

    Türkçe

    Türkçe

    2023

    KimyaYıldız Teknik Üniversitesi

    Kimya Ana Bilim Dalı

    PROF. DR. FATİH ÇAKAR