Kolemanit parçacık takviyeli PLA kompozit filament üretimi ve karakterizasyonu
Colemanite particle reinforced PLA composite filament production and characterization
- Tez No: 794585
- Danışmanlar: DR. ÖĞR. ÜYESİ AĞAH AYĞAHOĞLU, PROF. DR. HİLMİ YURDAKUL
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2023
- Dil: Türkçe
- Üniversite: Kütahya Dumlupınar Üniversitesi
- Enstitü: Lisansüstü Eğitim Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 72
Özet
Bu çalışmada eriyik yığma modelleme metodunu (FDM) kullanarak, parça imalatını sağlayan 3D yazıcıların, hammaddesi olan filamentler üzerinde araştırmalar yapılmış olup, kolemanit katkılı kompozit filament üretimi sağlanmıştır. Granül halindeki PLA'nın solvent içerisinde çözdürülmesi ile içinde birden fazla mineral barındıran toz halindeki kolemanitin (2CaO.3B2O3.5H2O), ağırlıkça sırasıyla %1, %2, %3 oranlarınca eklenip, karışımı sağlanmıştır. Elde edilen kompozit karışım, mekanik öğütücü vasıtasıyla granül boyutuna indirgenmiştir. Granül haldeki PLA- Kolemanit karışımı ve referans olarak kullanılacak olan saf PLA granülleri, çift vidalı plastik ekstrüzyon makinesinde, 1.75 mm çapında filament haline getirilmiştir. Çalışmada kolemanit katkılı, yanma direnci arttırılmış kompozit filament üretimi hedeflenmiştir. Saf PLA'dan elde edilen filament ve kompozit filamentler ile 3D yazıcıdan, çekme testi, darbe testi, yanmazlık testi için standart olarak belirlenen numunelerin baskıları alınmıştır. Çekme deneyi gerçekleştirildikten sonra, numunelerin SEM analizleri yapılmıştır. Darbe deneyi için 45 mm çapında 3 mm yüksekliğinde tasarlanan numuneler, Düşük Hızlı Darbe Test cihazından 3 kg yük ve konik uç ile 10 cm yükseklik şartları altında test edilmiştir. UL94 yanmazlık testi için 12,7 mm x 127 mm ebatlarında numuneler üretilmiş ve yanmazlık testine tabii tutulmuştur. Kolemanitin mineral yapısından kaynaklanan, içerisinde bulundurduğu çeşitli bileşikler neticesinde, yanma deneyinde olumsuz sonuçlar elde edilmiştir. Yapılan çekme deneyi ile kolemanit tozunun PLA yapısına uyum sağladığı görülmüştür. Oluşturduğu lifli yapılar ile sayesinde, kompozitin sünek bir yapıda olduğu gözlemlenmiştir.
Özet (Çeviri)
In this study, researches were carried out on the filaments, which are the raw materials of 3D printers that provide part manufacturing, by using the fused deposition modeling method (FDM), and the production of colemanite-added composite filament was provided. By dissolving the granular PLA in the solvent, colemanite (2CaO.3B2O3.5H2O) in powder form, which contains more than one mineral, was added at the rates of 1%, 2%, and 3% by weight, respectively, and the mixture was provided. The resulting composite mixture was reduced to granule size by means of a mechanical grinder. Granular PLA-Colemanite mixture and pure PLA granules to be used as a reference were turned into filaments with a diameter of 1.75 mm in a twin screw plastic extruder. In the study, it was aimed to produce colemanite added composite filament with increased combustion resistance. With the filament and composite filaments obtained from pure PLA, the samples determined as the standard for the tensile test, impact test, and flammability test were printed from the 3D printer. After the tensile test was performed, SEM analyzes of the samples were made. The samples designed for the impact test with a diameter of 45 mm and a height of 3 mm were tested under the Low Speed Impact Tester with a load of 3 kg and a conical tip under 10 cm height conditions. For UL94 flammability test, 12.7 mm x 127 mm samples were produced and subjected to flammability test. Negative results were obtained in the combustion test as a result of various compounds that colemanite contains, originating from its mineral structure. With the tensile test, it was seen that the colemanite powder adapts to the PLA structure. Thanks to the fibrous structures it creates, it has been observed that the composite has a ductile structure.
Benzer Tezler
- Deneysel ve CERN-FLUKA Monte Carlo simülasyon kodu yöntemleri kullanılarak 4,5 MeV enerjili hızlı nötronların borlu bileşik ve cevherler tarafından yavaşlatılmasına ilişkin parametrelerin belirlenmesi
Determine of parameters about attenuated of 4,5 MeV fast neutrons by boron compounds and ores using experimental and CERN-FLUKA Monte Carlo code methods
TURGAY KORKUT
Doktora
Türkçe
2010
Fizik ve Fizik MühendisliğiAtatürk ÜniversitesiFizik Ana Bilim Dalı
PROF. DR. ABDULHALİK KARABULUT
- Hidromagnezit-huntit (HH) kullanarak güç tutuşur poli (laktik asit) esaslı kompozit malzeme üretimi ve sinerjik etki çalışmaları
Production of flame retardent based poly (lactid acid) composite material using hidromagnesite–huntite (HH) and synergic effect studies
AYŞEGÜL ERDEM
Doktora
Türkçe
2022
Tekstil ve Tekstil MühendisliğiErciyes ÜniversitesiTekstil Mühendisliği Ana Bilim Dalı
PROF. DR. MEHMET DOĞAN
- Synthesis of tris(hydroxymethyl)aminomethane modified polystyrene based polymeric sorbent and removal of boron from aqueous solutions
Tris(hidroksimetil)aminometan ile modifiye edilmiş polistiren esaslı polimerik sorbentin hazırlanması ve sulu ortamdaki borun giderilmesinde kullanılması
ARZU ERSOY
Yüksek Lisans
İngilizce
2017
Polimer Bilim ve Teknolojisiİstanbul Teknik ÜniversitesiPolimer Bilim ve Teknolojisi Ana Bilim Dalı
PROF. DR. BAHİRE FİLİZ ŞENKAL
- Preparation of cross-linked poly (styrene) based resin amidated by staudinger reaction, modification with iminopropylene glycole and removal of the boron from aqueous solutions
Staudinger reaksiyonu ile aminlenmiş çapraz bağlı poli (stiren) esaslı reçinenin hazırlanması iminopropilen glikol ile modifikasyonu ve borun sulu çözeltilerden giderilmesinde kullanılması
ALEYNA BUĞÇE MASACI
Yüksek Lisans
İngilizce
2018
Polimer Bilim ve Teknolojisiİstanbul Teknik ÜniversitesiPolimer Bilim ve Teknolojisi Ana Bilim Dalı
PROF. DR. BAHİRE FİLİZ ŞENKAL
- An Investigation for the benefication of colemanite ore by flotation
Kolemanit cevherinin flotasyon yolu ile zenginleştirilmesinin araştırılması
İBRAHİM KONUK
Doktora
İngilizce
1999
Maden Mühendisliği ve MadencilikDokuz Eylül ÜniversitesiMaden Mühendisliği Ana Bilim Dalı
PROF. DR. İLKNUR CÖCEN