Assessment and simulation the impact of concrete strength on the structural performance of beams
Beton mukavemetinin kirişlerin yapısal performansı üzerindeki etkisinin değerlendirilmesi ve simülasyonu
- Tez No: 798156
- Danışmanlar: PROF. DR. ZEKİ HASGÜR
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2022
- Dil: İngilizce
- Üniversite: Altınbaş Üniversitesi
- Enstitü: Lisansüstü Eğitim Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: İnşaat Mühendisliği Bilim Dalı
- Sayfa Sayısı: 75
Özet
Betonun çekme mukavemeti, dış yükleme tarafından oluşturulan çekme gerilmesine daha az dayanma kabiliyetinde olduğundan, beton mukavemetinin artması, enine kesitteki çekme bölgesinin çekme gerilmesinin etkisini daha fazla kaldırabilme kabiliyetini artırabilir. çatlama bölümü durumuna ulaşmadan sınırlar. Çalışma, çekme bölgesinin iç dayanımını artırmak için betonun dayanımını artırma kapsamının etkili bir analizini oluşturmayı amaçlamıştır. Çalışma, kiriş genişliğinin, kirişin yüksekliğinin ve donatı alanının etkisini hesaba kattı ve ardından her parametrenin etki yüzdesini değerlendirdi. Kesitin yüksekliği daha büyük etki yüzdesini gösterdi, böylece çalışma, konsantre yük durumu için betonun basınç dayanımının yükün karesine bölünmesine atıfta bulunan dayanıklılık indeksi üzerindeki F(h) yüksekliğinin etkisine dayanan denklemler türetmiştir. ve üniform yükleme durumu için dağıtılmış yüklemenin karesi ile. Çalışma daha sonra F(h), b'yi elde etmek için çeşitli ışın genişliği değerleri için denklemi değiştirdi ve ardından çeşitli açıklık uzunluğu değerleri için F(h),b,h'yi elde etti. Çalışma, betonarme kirişin çeşitli yüksekliklerine ve genişliklerine dayalı olarak çatlamış yükün ve çatlamış üniform yüklemenin gerçek duruma yakın durumunu göstermek için her bir durum için türetilmiş denklemin olasılığını incelemek üzere iki durum yüklemesini (yoğunlaştırılmış yük ve üniform yükleme) kullandı. iki durum için mukavemet indeksi, denklemi işledikten sonra eğri uydurma teknikleri de dahil olmak üzere birçok çizelge oluşturarak incelenmiştir.Betonun mukavemeti 30 ila 50 MPa aralığında incelenmiş, çalışma sonuçları türetilen formüller ve çalışma gerilimi adımları ile açıklamıştır. RC boyutlarının belirli koşulları altında betonun dayanımını artırmak için karar vermeyi iyileştirmek için yeni denklemlerin uygulanabilirliğini gösteren düşük farklılıklar ile Çalışma, ANSYS programı kullanılarak 3 boyutlu görüntülerin simülasyonunu oluşturdu. belirtilen aralık, güvenlik faktörü değerlerine göre incelenmiştir.
Özet (Çeviri)
The tensile strength of concrete as it in less ability to resist the tension stress formed by the external loading, the increasing of the concrete strength can enhance the capability of the tension zone in the cross section to handle the effect of the tension stress for more upper limits without reaching the cracking section state. The study aimed to build effective analysis of the scope of increasing the strength of concrete to rise the internal strength of the tension region. The study took the effect of the width of beam, the height of the beam, and the reinforcement area into account then evaluated each parameter percent of impact. The height of the section showed the bigger impact percent so that the study derived equations based of the effect of the height F(h) on the strength index which referred to the compressive strength of concrete divided by the square of the load for concentrated load case and by the square of the distributed loading for uniform loading case. The study then modified the equation for various width of beam values to get F(h), b then for various span length values to get F(h),b,h. the study used the two cases loading (concentrated load and uniform loading to examine the possibility of the derived equation for each case to show the close to actual state of cracked load and cracked uniform loading based on various heights and widths of the RC beam. The strength index for the two cases was examined after the processing the equation by building many charts including curve fitting techniques. The strength of concrete was examined fro range 30 to 50 MPa, the study explained the results by the derived formulas and by the working stress steps with low differences indicating the applicability of the new equations to improve the decision making for increasing the strength of the concrete under specific conditions of the RC dimensions. The study built 3d images simulation using ANSYS program. The stress on the cross section for Fc in the mentioned range was investigated according the safety factor values
Benzer Tezler
- Jeopolimer beton malzemenin yapı ürünü ve malzemesi olarak çevresel sürdürülebilirlik performansının değerlendirilmesi
Evalution of environmental sustainability performance of geopolymer concrete material as a building product and material
ASLIHAN KAYHAN
Yüksek Lisans
Türkçe
2022
Mimarlıkİstanbul Teknik ÜniversitesiMimarlık Ana Bilim Dalı
PROF. DR. SEDEN ACUN ÖZGÜNLER
- Sigortacılık sisteminde aktif-pasif yönetimi ve Türkiye hayat sigortası örneğinde portföy performansının boyutlarını belirleyen faktörlerin irdelenmesine ilişkin bir model denemesi
Assets and liablity management in the insurance sector and investigating sectors that are determinating dimensions of the portfolio performance by relating to model testing in the Turkish life insurance sector
ALİ İHSAN DOĞAN
Doktora
Türkçe
2001
SigortacılıkMarmara ÜniversitesiBankacılık Ana Bilim Dalı
PROF.DR. ABDÜLGAFFAR AĞAOĞLU
- Uncertainty assessment for the supply chain system of a concrete company using Monte Carlo simulation
Bir beton firmasının tedarik zincirinin Monte Carlo silumasyonu ile belirsizlik değerlendirmesi
İNANÇ TAHA SERBEST
Yüksek Lisans
İngilizce
2021
Maden Mühendisliği ve MadencilikOrta Doğu Teknik ÜniversitesiMaden Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ ONUR GÖLBAŞI
- Mevcut bir apartman binasının alüminyum giydirme cephe sistemiyle yenilenmesinin enerji tüketimi ve CO2 emisyonu açısından değerlendirilmesi
Evaluating the renovation of an existing apartment building with an aluminum facade system in terms of energy consumption and CO2 emissions
İSMAİL KAMIŞ
Yüksek Lisans
Türkçe
2023
Enerjiİstanbul Teknik ÜniversitesiEnerji Bilim ve Teknoloji Ana Bilim Dalı
PROF. DR. HATİCE SÖZER
- End-of-life analysis for brick debris: Recovery, strength, life cycle cost and environmental assessment
Tuğla atıkları için yaşam sonu analizi: Kurtarma, dayanım, fiyat ve çevresel etki değerlendirmesi
DENİZ ÜÇER ERDURAN
Doktora
İngilizce
2018
MimarlıkOrta Doğu Teknik ÜniversitesiYapı Bilgisi Ana Bilim Dalı
PROF. DR. SOOFIA TAHIRA ELIAS OZKAN