PLC ve SCADA destekli pozisyon kontrolü
PLC and SCADA supported position control
- Tez No: 83892
- Danışmanlar: YRD. DOÇ. DR. FERHAT DALDABAN
- Tez Türü: Yüksek Lisans
- Konular: Elektrik ve Elektronik Mühendisliği, Electrical and Electronics Engineering
- Anahtar Kelimeler: Adım motoru, Konum denetimi, Motorlar, PLC, SCADA, Servo motorlar, Step motor, Position control, Motors, Programmable logic controller, SCADA, Servo motors
- Yıl: 1999
- Dil: Türkçe
- Üniversite: Erciyes Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Elektronik Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
ÖZET Bu çalışmada, birçok endüstriyel alanda ihtiyaç duyulan pozisyon kontrol sistemleri incelenmiş ve tek eksenli pozisyon kontrol sistemi gerçekleştirilmiştir. Tek eksenli pozisyon kontrol sistemi PLC ve SCADA ile kontrol edilmektedir. Çalışmanın ilk bölümünde, pozisyon kontrol için gerekli olan programlanabilir lojik kontrolör incelenmiştir. İkinci bölümde, pozisyon kontrol sistemlerinde kullanılan motor ve sürücüler anlatılmıştır. Pozisyon kontrol sisemleri, daha çok servomotor ve step motor kullanılarak gerçekleştirildiği için bu motorlar üzerinde daha çok durulmuştur. Üçüncü bölümde ise, pozisyon geribesleme elemanları tanıtılmıştır. Dördüncü bölümde, veri tabanlı gözetleme ve kontrol sistemi açıklanmıştır. Beşinci bölümde, açık ve kapalı çevrim pozisyon kontrol tipleri anlatılmıştır. Tek eksenli kapalı-çevrim pozisyon kontrol sistemi tasarlanmış ve tasarlanan bu sistem PLC ve SCADA kullanılarak pratik olarak gerçekleştirilmiştir. Çalışmanın sonunda çok eksenli pozisyon kontrol sistemlerinin gerçekleştirilmesi için önerilerde bulunulmuştur. Son bölümde ise; elde edilen sonuçlar değerlendirilmiştir.
Özet (Çeviri)
VI ABSTRACT In this study, position control systems required on many industrial areas have been investigated and single axis control system has been designed. The single axis position control system is controlled by Programmable Logic Controller (PLC) and SCADA (Supervisory Control And Data Acquisition). In the first chapter of this study, PLC required for position control has been examined. In the second chapter, motors and drivers used in position control systems have been explained. Due to wide use of servo and step motors in position control systems, they have been examined in detail in this chapter. In the third chapter, position feedback components have been introduced. Supervisory control and data acquisition has been explained in the chapter four. Open loop and close loop position control types have been stated in the fifth chapter. Also, a closed loop position control system has been designed and it has been practically designed by using PLC and SCADA. At the end of the study, some suggestions have been done to design, multi-axis position control systems. In the last chapter the results obtained were discussed.
Benzer Tezler
- Doğal gaz SCADA otomasyon uygulamalarında ana kontrol merkezi ile haberleşmeyi sağlayan SCADA - otomasyon sistemlerinin; Cicode Scada ve PLC programlarındaki mevcut parametreler yardımı ile bilgisayar destekli yeni arayüzler oluşturulması
Natural gas SCADA automatıon applications with the main control center provides communications to the scada - automation systems; Cicode SCADA and PLC in program assistance available parameters interface creation with new computer aided
GÖKMEN SALĞAR
Yüksek Lisans
Türkçe
2010
Elektrik ve Elektronik MühendisliğiKahramanmaraş Sütçü İmam ÜniversitesiElektrik-Elektronik Mühendisliği Ana Bilim Dalı
PROF. DR. M. KEMAL KIYMIK
- Sıvı seviyesinin PLC'de PID yöntemini kullanarak SCADA destekli kontrolü
PID control of liquid level system via PLC supported by SCADA
İDRİS KÜÇÜKKAVRUK
Yüksek Lisans
Türkçe
2002
Elektrik ve Elektronik MühendisliğiYıldız Teknik ÜniversitesiElektrik Mühendisliği Ana Bilim Dalı
PROF. DR. HALİT PASTACI
- PLC ve SCADA kullanarak bir bina otomasyon sisteminin gerçeklenmesi, uzaktan kontrolü ve izlenmesi
Implementation, remote control, and monitoring of a building automation system using PLC and SCADA
FATİH ÖZEN
Yüksek Lisans
Türkçe
2019
Elektrik ve Elektronik MühendisliğiTekirdağ Namık Kemal ÜniversitesiElektronik ve Haberleşme Mühendisliği Ana Bilim Dalı
PROF. DR. CEVAT ERDAL
- PLC (programlanabilir lojik kontrol cihazı) ve SCADA (yönetsel denetim ve veri toplama) ile endüstriyel otomasyonu uygulaması
Industrial aoutomation application with PLC (programable logic controller) and SCADA (super visory control and data acquisition)
ADEM ÇİLEK
Yüksek Lisans
Türkçe
2005
Elektrik ve Elektronik MühendisliğiGazi ÜniversitesiElektrik-Elektronik Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. İRES İSKENDER
- Endüstriyel otomasyon sistemlerinin mekatronik kontrol yöntemleri ve mekatronik sistem uygulaması
Mechatronic control methods of industrial automation systems and an application of mechatronic system
ARİF ÖZKAN
Yüksek Lisans
Türkçe
2005
Teknik EğitimZonguldak Karaelmas ÜniversitesiMakine Eğitimi Ana Bilim Dalı
DOÇ.DR. KERİM ÇETİNKAYA