Geri Dön

Su atomizasyon yöntemi ile metal tozu üretimi için yeni bir santrifuj atomizasyon sistemi tasarımı ve imalatı

Design and construction of a centrifugal atomization disc system by a new types of water atomization method for metal powder productions

  1. Tez No: 845729
  2. Yazar: HÜSEYİN KARASU
  3. Danışmanlar: PROF. DR. CENGİZ DOĞAN
  4. Tez Türü: Doktora
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2024
  8. Dil: Türkçe
  9. Üniversite: Harran Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 151

Özet

Bu çalışmada, imalat sanayinde yaygın olarak kullanılan metal tozlarının daha ekonomik nasıl üretilebileceği su atamizasyon yöntemi ile araştırılmıştır. Su atomizasyon yönteminde kullanılan pompa fanı, ısıl fırın ve demir potanın üretilecek metal tozunun karakteristik özelliği üzerindeki etkileri ilgili literatürden yararlanılarak belirlenmiştir. Su atomizasyon yöntemi ile metal tozu üreten ve bir pompa fanı, bir ısıl fırın ve bir demir potadan oluşan bir deney düzeneğinin tasarımı ve imalatı gerçekleştirilmiştir. Deney düzeneğinde pompa fanının dönüş hızı, sıvı metal çıkış hızı ve sıvı metal sıcaklığı istenilen değerlerde hesaplanabilmektedir. Ayrıca metal tozu özelliklerini etkileyen faktörler incelenmiştir. Su atomizasyon yönteminde kullanılan pompa fanı, metal tozları üzerindeki etkilerini incelemek için farklı şekil ve boyutlarda test edilmiştir. Isıl fırın için yüksek sıcaklığa dayanıklı kanallı ateş tuğlası, ısı kaybını en düşük seviyede tutmak için ise düşük sıcaklığa ve ısıya dayanıklı gazbeton malzeme kullanılmıştır. Isıl fırını ısıtmak için yüksek erime sıcaklığına sahip bir nikel-krom elektrik direnç teli kullanılmıştır. Dairesel kanallı ateş tuğlalarının kanallarına uygun çap, uzunluk ve sarım sayısı için geliştirilen formüller kullanılarak söz konusu elektrik direnci elde edilmiştir. Pota, yüksek ısı direnci ve ısı iletim katsayısı nedeniyle demir malzemeden imal edilmiştir. Isıl fırının tasarımında sıcaklığın önemli bir rolü vardır. Sıcaklık ölçümlerinde termokupl kullanılmıştır. Isı transferi ve sınır koşullarında kullanılan denklemler, potanın sıcaklık dağılımı için kullanılır. Çalışmada üretilen pota ve fırınların benzer imalat teknolojilerine göre daha ekonomik ve daha kolay imal edilmesi çalışmanın öne çıkan yönüdür. Kurşun ve diğer düşük erime noktasına sahip metaller üzerinde çok sayıda deney yapılmıştır. Üretilen tozlar elek analizlerinden geçirilerek ortalama toz boyutları ve toz dağılımları belirlenmiştir. Tozlar metalografik yöntemlerle optik mikroskop altında incelenmiştir. Test sonuçları ile üretilen metal tozlarının TM alanında kullanımının uygun olduğu tespit edilmiştir. Küre şeklindeki çok küçük tozların, suya çarpmadan havada katılaştığı görülmüştür. Büyük tozların ise su etkisiyle katılaştıklarından karmaşık geometrik şekiller oluşturdukları tespit edilmiştir. Çok kanallı disk kullanımının toz üretim miktarında önemli bir parametre olmadığını göstermektedir.

Özet (Çeviri)

The study has proven that metal powders, which are widely used in the manufacturing industry, can be produced more economically. At the beginning of the research, the effects of the pump fan, thermal furnace, and iron crucible used in the water atomization method on the characteristic feature of the metal powder to be produced were determined by using the relevant literature. Thus, the design and manufacture of the experimental setup to produce metal powder by the water atomization method were carried out. This experimental setup; consists of a pump fan, a thermal furnace, and an iron crucible. In the experimental setup, the rotation speed of the pump fan, the liquid metal outlet velocity, and the liquid metal temperature can be calculated at desired values. In addition, the factors affecting the metal powder properties were investigated. The pump fan used for the water atomization method was tested in different shapes and sizes to examine the effects on metal powders. High-temperature-resistant channel fire bricks were used for the thermal furnace, and a low-temperature and heat-resistant aerated concrete material was used to keep the heat loss at the lowest level. A high melting temperature nickel-chromium electrical resistance wire was used to heat the thermal furnace. The electrical resistance in question was obtained by using the formulas developed for the diameter, length, and number of turns suitable for the channels of the circular fire bricks and it is fixed by connecting, and the resistance wire is connected to the lathe machine from both ends of the rod and spiraled. The crucible is made of iron material due to its high heat resistance and heat transmission coefficient. The temperature has an important role in the design of this thermal furnace. For this, a temperature sensor called a thermocouple is used. Instant temperature values are shown on the screen of this temperature sensor. The equations used in heat transfer and boundary conditions are used for the temperature distribution of the crucible. The prominent aspect of the study is that the crucibles and furnaces manufactured in the study are more economical and easier to manufacture than similar manufacturing technologies. Numerous experiments were conducted on lead and other low-melting metals. The powders produced were brought from the sieve analysis and the average powder sizes and powder distributions were examined. The powders were examined under an optical microscope by metallographic methods. The test results have determined that the metal powders produced are suitable for use in the field of powder metallurgy. Very small powders are spherical in shape. This smallness of dust indicates that they solidified in the air without hitting the water. The shapes of large powders have complex geometrical shapes because they are solidified by water impact. It shows that the use of multi-channel discs is not an important parameter in the amount of metal powders production.

Benzer Tezler

  1. Atomizasyon yöntemiyle toz metal üretimi ve tozların karakterizasyonu

    Production of metallic powders by atomization and characterization of the powders

    İREM ŞEBNEM AKPINAR

    Yüksek Lisans

    Türkçe

    Türkçe

    2011

    Metalurji MühendisliğiDokuz Eylül Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. KAZIM ÖNEL

  2. Yüksek karbonlu toz metal çeliklerin martemperlenmesi ve aşınma davranışlarının incelenmesi

    Martempering of high carbon powder metal steels and investigation of wear behavior

    KEVSER CEYDA GÜNEY

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Metalurji MühendisliğiGazi Üniversitesi

    İleri Teknolojiler Ana Bilim Dalı

    PROF. DR. AHMET GÜRAL

  3. TiC/AA2024 kompozitlerin mekanik alaşımlama yöntemiyle üretimi ve mekanik özelliklerinin belirlenmesi

    Production of TiC/AA2024 composites by mechanical alloying method and determination of mechanical characteristics

    ABDULLAH YILMAZ

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Makine MühendisliğiNecmettin Erbakan Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. AHMET AKDEMİR

    DR. ÖĞR. ÜYESİ CİHAD NAZİK

  4. Yağ optimizasyonu yöntemiyle metal tozu üretiminin incelenmesi

    Başlık çevirisi yok

    AHMET ONUR

    Yüksek Lisans

    Türkçe

    Türkçe

    1996

    Makine MühendisliğiKaradeniz Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF.DR. FAZLI ARSLAN