Geri Dön

Öğütme devresinin simülasyonu: Ortaklar bakır zenginleştirme tesisi, Gaziantep/Türkiye

Simulation of grinding circuit: Ortaklar copper processing plant, Gaziantep/Türkiye

  1. Tez No: 900053
  2. Yazar: MAMADOU BOYE DIALLO
  3. Danışmanlar: PROF. DR. OKTAY BAYAT
  4. Tez Türü: Yüksek Lisans
  5. Konular: Maden Mühendisliği ve Madencilik, Mining Engineering and Mining
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2024
  8. Dil: Türkçe
  9. Üniversite: Çukurova Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Maden Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 62

Özet

Bu yüksek lisans çalışması kapsamında; Miryıldız Bakır Zenginleştirme Tesisindeki (Gaziantep, Türkiye) öğütme devresinin performansı simülasyon ve kütle denge analizleri ile değerlendirilmiştir. Tesise beslenmekte olan tüvanan cevherin, tesis tasarımı sırasında çalışılan cevherden tamamen farklı mineralojik ve kimyasal özelliklere sahip olduğu tespit edilmiştir. Bu nedenle mevcut akım şemasının, kullanılan cevherin zenginleştirilmesi için uygun olup olmadığını belirlemek amacıyla üç farklı simülasyon çalışması gerçekleştirilmiştir. Simülasyon için METSIM (Demo versiyonu) yazılımı kullanılmıştır. 70 t/s, 90 t/s ve 100 t/s besleme tonajlarında simülasyon yapılmıştır. 70 t/s besleme miktarında P80 değerinin 33,72 mm'den 0,036 mm'ye düştüğü ve flotasyon beslemesinin katı içerik oranının %35,27 olduğu tespit edilmiştir. 90 t/s besleme miktarında ise hidrosiklon üst akımına ait P80 değerinin 0,040 mm'ye düştüğü, katı içerik oranının ise %31,06 olarak korunduğu belirlenmiştir. Son olarak; tesis besleme tonajı 100 t/s seviyesine çıkarılmış ve hidrosiklon P80 değerinin 0,044 mm olduğu, flotasyon beslemesinin katı içerik oranının ise %32,39 olduğu görülmüştür. Kütle denge analizlerinde, Model-1 ve Model-2 üzerinden iki farklı öğütme devresi değerlendirilmiştir. Model-1'de, 70 t/s katı ve 26 t/s suyun SAG değirmenine beslenmesiyle %73 katı konsantrasyonuna sahip bir bulamaç elde edilmiştir. Bu işlem sonucunda, dolaşım yük oranı %250 olarak belirlenmiş ve bypass oranının %34,66 olduğu tespit edilmiştir. Model-2'de ise, 95 t/s katı ve 49 t/s su beslenmesiyle %66 katı konsantrasyonu elde edilmiştir ve dolaşım yük oranı yine %250 olarak belirlenmiştir; bypass oranı ise %25,79 olarak hesaplanmıştır. Simülasyon sonuçları, JKSimMet yazılımı kullanarak yapılan benzer simülasyon çalışmaları ile karşılaştırılmış ve iki simülasyon arasında yüksek bir tutarlılık tespit edilmiştir. Bu kapsamda yapılan simülasyonlar ve kütle denge analizleri, mevcut öğütme devresi koşullarını iyileştirmek ve daha sürdürülebilir bir cevher zenginleştirme sürecine geçiş yapılmasına yönelik değerli bilgiler sunmaktadır.

Özet (Çeviri)

In this master's thesis, the performance of the grinding circuit at the Miryıldız Copper Processing Plant (Gaziantep, Türkiye) was evaluated through simulation and mass balance analyses. It was determined that the ore currently fed to the plant had completely different mineralogical and chemical properties compared to the ore studied during the plant's design phase. Therefore, three different simulation studies were conducted to determine whether the current flow sheet was suitable for the beneficiation of the ore being processed. The grinding circuit performance was simulated using METSIM (DEMO version) software. Simulations were conducted at three different feed tonnages: 70 t/h, 90 t/h, and 100 t/h. When the feed tonnage was set at 70 t/h, the P80 value was reduced from 33.72 mm to 0.036 mm, and the solid content of the flotation feed was found to be 35.27%. The P80 value of the hydrocyclone overflow was reduced to 0.040 mm, while the solid content was maintained at 31.06% when the feed tonnage was increased to 90 t/h. As a third simulation, the feed tonnage was raised to 100 t/h, and the P80 value of the hydrocyclone overflow was 0.044 mm, with the solid content of the flotation feed at 32.39%. In the mass balance analyses, two different grinding circuits were evaluated using Model-1 and Model-2. In Model-1, a slurry with a solid concentration of 73% was obtained by feeding 70 t/h of solids and 26 t/h of water to the SAG mill. As a result of this process, the recirculation load was determined to be 250%, and the bypass ratio was 34.66%. In Model-2, a solid concentration of 66% was obtained by feeding 95 t/h of solids and 49 t/h of water, with the recirculation load again determined to be 250% and the bypass ratio calculated as 25.79%. The simulation results were compared with similar studies using JKSimMet software, and a high consistency was found between the two simulations. These simulation and mass balance analyses provide valuable insights for improving current grinding circuit conditions and transitioning to a more sustainable beneficiation process.

Benzer Tezler

  1. Öğütme yardımcılarının çimento öğütme devresi performansı üzerine etkilerinin modellenmesi ve simülasyonu

    Modelling and simulation of the grinding aids effect on cement grinding circuit performance

    NURETTİN ALPER TOPRAK

    Doktora

    Türkçe

    Türkçe

    2015

    Maden Mühendisliği ve MadencilikHacettepe Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    PROF. DR. AHMET HAKAN BENZER

  2. Simülasyon yardımıyla endüstriyel eleme işlemini etkileyen parametrelerin incelenmesi

    Simulation aided investigations on the parameters affecting industrial screening

    AHAD AGHLMANDI HARZANAGH

    Doktora

    Türkçe

    Türkçe

    2020

    Maden Mühendisliği ve MadencilikHacettepe Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    PROF. DR. ŞEVKET LEVENT ERGÜN

    DR. EREN CANER ORHAN

  3. Bakır cürufu öğütme devresinin bilgisayar destekli performans değerlendirmesi ve optimizasyonu

    Computer aided performance evaluation and optimization of copper slag grinding circuit

    ORBERK MERT MERCAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2017

    Maden Mühendisliği ve MadencilikHacettepe Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. NURULLAH METİN CAN

  4. Bilgisayar destekli otojen öğütme devre tasarımı ve optimizasyonu

    Computer aided design and optimization of an autogenous mill grinding circuit

    AYŞE TUĞBA CEBECİ

    Yüksek Lisans

    Türkçe

    Türkçe

    2011

    Maden Mühendisliği ve MadencilikHacettepe Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    PROF. DR. Ş. LEVENT ERGÜN

  5. Karıştırmalı bilyalı değirmenlerin ara ürün öğütme devrelerinde performansının modellenmesi

    Modelling of the performance of the stirred media mills in regrinding circuits

    SERKAN DİKMEN

    Doktora

    İngilizce

    İngilizce

    2008

    Maden Mühendisliği ve MadencilikHacettepe Üniversitesi

    Maden Mühendisliği Ana Bilim Dalı

    PROF. DR. Ş. LEVENT ERGÜN