Monolitik zirkonyada yapılan oklüzal uyumlamalar sonrasında oluşan yüzey pürüzlülükleri ve renk değişimleri üzerinde farklı polisaj sistemlerinin etkilerinin incelenmesi
Investigation of the effects of different polishing systems on surface roughness and color changes following occlusal adjustments in monolithic zirconia
- Tez No: 919847
- Danışmanlar: PROF. DR. YAKUP ŞİNASİ SARAÇ
- Tez Türü: Diş Hekimliği Uzmanlık
- Konular: Diş Hekimliği, Dentistry
- Anahtar Kelimeler: Monolitik zirkonya, Polisaj sistemleri, Renk değişimi, Yüzey pürüzlülüğü, Color change, Monolithic zirconia, Polishing systems, Surface roughness
- Yıl: 2024
- Dil: Türkçe
- Üniversite: Ondokuz Mayıs Üniversitesi
- Enstitü: Diş Hekimliği Fakültesi
- Ana Bilim Dalı: Protetik Diş Tedavisi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 99
Özet
Amaç: Bu tez çalışmasının amacı, monolitik zirkonyaya klinik uyumlamayı taklit etmek için yapılan aşındırma işlemi sonrası uygulanan farklı polisaj sistemlerinin, materyalin yüzey pürüzlülüğü ve renk değişimi üzerindeki etkilerini incelemektir. Materyal ve Metot: Çalışmada, presinterize A2 renkli monolitik zirkonya blok (DD Bio ZX2 color, Dental Direkt GmbH, Almanya) kullanıldı. Örnekler CAD/CAM teknolojisi ile üretildi. Glaze işlemi sonrası örnekler beş gruba ayrıldı (n=13) ve başlangıç renk ölçümü spektrofotometre (SpektroShade, MHT Optic Research, İsviçre) ile yapıldı. Kontrol (K) grubu hariç diğer örnekler ince taneli elmas frez (837LF FG 014, Meisinger, Almanya) ile aşındırıldı. Ardından dört farklı polisaj sistemi (Grup E: EVE Diacera Twist, Grup SC: Shofu Ceramaster Coarse- Ceramaster, Grup SD: Shofu Direct Dia, Grup U: Ultradent Daimond Polish Mint) uygulandı. İkinci renk ölçümleri yapılarak ΔE00 değerleri hesaplandı. Yüzey pürüzlülüğü AFM ile ölçüldü. İstatistiksel analizde Shapiro-Wilk, Levene, Tek Yönlü Varyans Analizi ve Tamhane Testi kullanıldı. Bulgular: Farklı polisaj sistemleri uygulanan örneklerin sonuç yüzey pürüzlülüğü değerleri arasında anlamlı farklar bulunurken (p0.05). Grup SD en yüksek yüzey pürüzlülük değerine sahipken, en düşük değer K grubunda gözlemlenmiştir. En yüksek ortalama renk değişim değeri (ΔE00) Grup E'de görülürken; en düşük ortalama renk değişim değeri Grup U'da görülmüştür. Sonuç: Simantasyon sonrası uyumlama yapılan restorasyonların polisajı için ağız içi polisaj sistemleri, glaze işlemi kadar etkili olmasa da klinik olarak kabul edilebilir değerler vermiştir.
Özet (Çeviri)
Aim: The aim of this thesis is to investigate the effects of different polishing systems, applied after grinding procedures to simulate clinical adjustments, on the surface roughness and color change of monolithic zirconia. Materials and Methods: In this study, presintered A2-colored monolithic zirconia blocks (DD Bio ZX2 color, Dental Direkt GmbH, Germany) were used. The samples were produced using CAD/CAM technology. After the glaze procedure, the samples were divided into five groups (n=13), and initial color measurements were made with a spectrophotometer (SpectroShade, MHT Optic Research, Switzerland). Except for the control group (C), the other samples were ground with a fine-grain diamond bur (837LF FG 014, Meisinger, Germany). Subsequently, four different polishing systems were applied (Group E: EVE Diacera Twist, Group SC: Shofu Ceramaster Coarse- Ceramaster, Group SD: Shofu Direct Dia, Group U: Ultradent Daimond Polish Mint). Second color measurements were made, and ΔE00 values were calculated. Surface roughness was measured using AFM. For statistical analysis, the Shapiro-Wilk test, Levene's test, one-way ANOVA, and Tamhane's test were used. Results: Significant differences were found in the final surface roughness values among the samples treated with different polishing systems (p0.05). Group SD showed the highest surface roughness value, whereas the lowest value was observed in Group C. The highest average color change value (ΔE00) was observed in Group E, while the lowest average color change value was found in Group U. Conclusion: Intraoral polishing systems for adjustments after cementation provided clinically acceptable results, though less effective than glazing.
Benzer Tezler
- Farklı yüzey aşındırma işlemlerinin monolitik zirkonya materyalinin yaşlandırma öncesi ve sonrası bükülme direncine ve faz dönüşümüne etkisi
The effects of different surface treatments on flexure strength and phase transformation of monolithic zirconia material before and after aging protocol
EMRE AKTAN
Doktora
Türkçe
2023
Diş Hekimliğiİstanbul ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
DOÇ. DR. NAZMİYE ŞEN
- Farklı adeziv sistemler kullanılarak yapılan immediate dentin sealing (hemen dentin kapama) işleminin monolitik zirkon blokların dentine olan bağlanma dayanımı üzerine etkisi
The effect of immediate dentin sealing procedure using different adhesive systems on the bond strength of monolithic zirconia to dentin
LEYLA FAZLIOĞLU
Diş Hekimliği Uzmanlık
Türkçe
2023
Diş HekimliğiBezm-i Alem Vakıf ÜniversitesiRestoratif Diş Tedavisi Ana Bilim Dalı
DOÇ. DR. BURCU OĞLAKÇI
- İmplant destekli sabit protezlerde CAM/CAM sistemleri ile üretilen destek ve üst yapı restorasyonlarının sonlu elemanlar stres analiz yöntemi ve kırılma direnci testi ile karşılaştırmalı olarak incelenmesi
The comparatively investigation of abutment and crown restorations produced by CAD/CAM systems in implant supported fixed prostheses using the finite element stress analysis method and fracture resistance test
NAZİRE ESRA BAĞDATLI
Doktora
Türkçe
2016
Diş HekimliğiAnkara ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
PROF. DR. AHMET ERSAN ERSOY
- All-On-Four konsepti kullanılarak farklı tasarımlar ve materyallerle üretilen protezlerin stres dağılımının sonlu elemanlar analiz yöntemi ile incelenmesi
'evaluation of stress distribution of prosthesis produced with different designs and materials using the All-On-Four concept with finite element analysis method'
DAMLA GÜNEŞ ÜNLÜ
Doktora
Türkçe
2019
Diş HekimliğiErciyes ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
DOÇ. DR. KEREM KILIÇ
- Maksiller all-on-four implant tasarımları üzerine tam ark sabit protetik üst yapılar ile hazırlanan farklı modellerin üç boyutlu sonlu elemanlar stres analiz yöntemi ile biyomekanik olarak değerlendirilmesi
Biomechanical examinations i̇n different models prepared with maxillary all-on-four i̇mplant designs and full arch fixed prosthetic upper structures: Three dimensional finite element stress analysis method
ZEKİYE BEGÜM GÜÇLÜ
Doktora
Türkçe
2020
Diş HekimliğiAnkara ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
PROF. DR. AYHAN GÜRBÜZ