Çelik kolon taban plaka tasarımında farklı yönetmeliklerin karşılaştırılması
Comparison of different codes in the design of steel column base plates
- Tez No: 970605
- Danışmanlar: PROF. DR. RAMAZAN ÖZÇELİK
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2025
- Dil: Türkçe
- Üniversite: Akdeniz Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Kolon taban plakaları, yapılarda yatay ve düşey yüklerin yapıdan temele güvenli bir şekilde aktarılmasının yanı sıra, kolon ile temel arasındaki temas alanının artırılmasına yardımcı olan, kolondan temele uygulanan gerilmeyi azaltan ve temele eşit olarak dağıtan ve sonuçta yapının stabilitesini sağlayan önemli bağlantı elemanıdır. Aslında, uygulanan gerilme, temelin taşıyabileceği gerilme değerine kadar azaltılmalıdır, bu nedenle kolon taban plakasının alanı, kolon kuvvetinden kaynaklanan basınç gerilmesini yeterli güvenilirlikle temele aktaracak kadar büyük olmalıdır. Taban plakası, çekme kuvvetlerini doğrudan taşımaz söz konusu bu kuvvet ankraj çubukları tarafından taşınır. Ancak, bu kuvvetlerin güvenli aktarımı için plakanın yeterli rijitliğe ve şekil bütünlüğüne sahip olması gerekir. Farklı coğrafi, iklimsel ve operasyonel koşullar, farklı standartların ortaya çıkmasına neden olmuş, bunun sonucunda her standarda kolon taban plakasının tasarımı için kendi kuralları ve düzenlemeleri oluşmuştur. Bu standartların değerlendirilmesi ve karşılaştırılmasına dayalı olarak, yapısal tasarım, güvenliğin sağlanmasında, yapıların ekonomik optimizasyonunda ve uluslararası koordinasyon ve uyumlulukta önemli bir rol oynamaktadır. Bu tezde, 1000x1000x406 mm boyutlarındaki temele aynı tip statik yüklerin etkidiği durumlarda kolon taban plakalarının tasarımı için Amerikan (AISC), Avrupa (Eurocode) ve Türkiye (Türk Standartları) olmak üzere üç standart incelenmiştir. Yukarıdaki üç standardın değerlendirilmesinde doğru sonuçlar elde edebilmek için, kolona uygulanan yüklerin türü ve miktarı, kolon profilinin türü, temelin beton basınç dayanımı, kolon ile kolon taban plakası arasındaki bağlantı türü (rijit), uygulama ve yapım koşulları dahil olmak üzere tüm parametrelerin tamamen aynı uygun olduğu kabul edilmiştir. Yukarıdaki koşullar dikkate alındığında, AISC standardına göre kolon tabanı için gerekli minimum plaka kalınlığının 50 mm olduğu, aynı koşullar için Eurocode ve Türk Standartlarına göre ise minimum plaka kalınlığının 32 mm olduğunu sonucuna varılmıştır. Değerlendirme sonuçları, AISC standardına göre minimum ankraj çubuğu çapının 16 mm olduğunu gösterirken, söz konusu değerlerin Türk Standardı ve Eurocode'e göre sırasıyla 22 mm ve 24 mm olduğunu göstermektedir.
Özet (Çeviri)
Column base plates are important connections in structures that help to safely transfer horizontal and vertical loads from the structure to the foundation, as well as to increase the contact area between the column and the foundation, reducing and evenly distributing the stress applied from the column to the foundation and ultimately ensuring the stability of the structure. In fact, the applied stress must be reduced enough that the foundation can withstand the reduced stresses, so the area of the column base plate must be large enough to transfer the compressive stress due to the column force to the foundation with sufficient reliability. The base plate does not directly resist tensile forces, this function is carried out by the anchor rods. However, in order to ensure the safe transfer of these forces, the plate must possess adequate rigidity and structural integrity. Different geographical, climatic and operational conditions have led to the emergence of different standards, resulting in each standard having its own rules and regulations for the design of structures, especially the column base plate. Based on the evaluation and comparison of these standards, structural design plays an important role in ensuring safety, economic optimization of structures and international coordination and harmonization. In this thesis, three standards, namely American (AISC), European (Eurocode) and Turkish (Turkish Standards) are analyzed for the design of column bases when the same type of static loads are acting on a 1000x1000x406 mm foundation. In order to obtain accurate results in the evaluation of the above three standards, it was assumed that all parameters, including the type and amount of loads applied to the column, the type of column profile, the concrete compressive strength of the foundation, the type of connection (rigid) between the column and the column base plate, and the application and construction conditions, are exactly the same or in accordance with the alternative standard. Considering the above conditions, the results obtained show that the minimum thickness required for the column base according to the AISC standard is 50 mm, while the minimum thickness according to Eurocode and Turkish Standards for the same conditions is 32 mm. The evaluation results show that the minimum anchor rod diameter according to the AISC standard is 16 mm, while according to the Turkish Standards and Eurocode it is 22 mm and 24 mm, respectively.
Benzer Tezler
- Deprem bölgelerinde yığma yapı tasarımının yönetmeliğe göre incelenmesi
Examination of masonry structure design on seismic zones in accordance with the relevant regulation
NURGÜL AKGÜNDÜZ
Yüksek Lisans
Türkçe
2004
Mimarlıkİstanbul Teknik ÜniversitesiMimarlık Ana Bilim Dalı
DOÇ. DR. BİLGE IŞIK
- Betonarme taşıyıcı sistemlerin tasarımında maliyet optimizasyonu için çelik sistemlerin kullanılması
The usage of steel structural systems to optimize the total cost of reinforced concrete structural systems
VEYSEL KONUK
Yüksek Lisans
Türkçe
2019
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. FETHİ KADIOĞLU
- Experimental study of earthquake simulator for cold-formed lightweight steel structures
Soğuk şekillendirilmiş hafif çelik yapılar için deprem simülatörünün deneysel çalışması
FUAD MOHAMMED AHMED AL-GAADI
Yüksek Lisans
İngilizce
2020
İnşaat MühendisliğiYıldız Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ FATİH ALEMDAR
- Kolon altı sismik izolatör kuvvet analizi
Force analysis of seismic isolator under the column
MEHMET TOKER
Doktora
Türkçe
2015
Deprem MühendisliğiDokuz Eylül ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. ONUR SAYMAN
- Çok katlı çelik yapıların tasarımı
Design of high rise steel structures
YUNUS EMRE ÇAĞATAY
Yüksek Lisans
Türkçe
2006
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ.DR. FİLİZ PİROĞLU