AISI 304 paslanmaz çeliğinin mikro yapı ve aşınma davranışının incelenmesi
Investigation of microstructure and wear behaviour of AISI 304 stainless steel
- Tez No: 98215
- Danışmanlar: PROF. DR. ZAFER S DOĞANTAN, PROF. DR. M. MUSTAFA YILDIRIM
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Ostenitik paslanmaz çelik, mikro yapı, aşınma davranışı, Austenitic stainless steel, microstructure, wear behaviour
- Yıl: 2000
- Dil: Türkçe
- Üniversite: Mustafa Kemal Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 58
Özet
ÖZET AISI 304 PASLANMAZ ÇELİĞİN MİKRO-YAPI VE AŞINMA DAVRANIŞLARININ İNCELENMESİ Bu çalışmada; % 18 Cr, % 8 Ni içeren ostenitik paslanmaz çeliklerin iç yapı özellikleri, aşınma davranışları ve diğer mekanik özellikleri incelenmiştir. Deneysel çalışma için hazırlanmış numunelere optik mikroskopta içyapı incelemesi, mikro sertlik, Charpy V-çentik darbe ve pim-disk aşınma testleri yapılmıştır. Paslanmaz çeliklerin tanıtılması, türleri ve kullanım yerleri hakkında genel bilgiler verilmiş; paslanmaz çeliklerden AISI 304 paslanmaz çeliğin mikro yapısı, çeliği oluşturan elementler ve miktarları, bu çeliğin mekanik özellikleri ve aşınma davranışı araştırılmıştır. Aşınma davranışı incelemesinde; numunenin değişken yükler altında aşınma davranışı, değişken devirler altındaki aşınma davranışı, sabit yük, sabit devirli yol periyotlarındaki aşınma davranışları araştırılmıştır. Değişken devirli aşınma deneylerinde belirli bir devir sayısına (kritik devire) kadar devir sayısı artışı ile aşınmadaki artışın ters orantılı olarak değiştiği, bu devir sayısından itibaren aşınmada görülecek artışın devir sayısındaki artışla yaklaşık doğru orantılı bir şekilde geliştiği belirlenmiştir. Adhesiv aşınma direncinin yüzey sertliği ve mikro sertlik ile ilişkisi tespit edilip bütün numunelerde aşınma direnci ve yüzey sertliği arasında lineer bir ilişkinin varlığı açıkça ortaya konmuştur. Yapıda bulunan 5 ferrit ve bunun ayrışmasından meydana gelen a fazı ile metal karbürlerin M23C6 yapılarının varlığı belirlenmiştir. Bunlardan a fazı ve bir miktar da M23C6 karbürün yapıda bulunması aşınma direncinin yükselmesinde belli ölçülerde etkili olmaktadır. 2000, 58 Sayfa
Özet (Çeviri)
ABSTRACT In this work, AISI 304 austenitic stainless steel (containing 18 % Cr and 8 % Ni ) is chosen to investigate wear resistance and the effects of microstructure and test parameters on wear behaviour. The experiments conducted within the framework of this project included microstructural observations by optical microscopy, Brinell-hardness measurements, Charpy fracture toughness and pin-disc wear tests. The present work covers an introduction of stainless steels and their types. As a focus point of the thesis, AISI 304 stainless steel alloy is reviewed in detail regarding microstructure, alloying elements used in this type of steels and its mechanical properties, and especially its tensile strength and wear resistance. The experiements conducted on the samples include investigation of wear resistance of samples under three variables, which are the length of wear rotational speed, and the magnitude of load. It was observed that all other experiments other than that were carried out under varying rotational speeds gave expected results. Surprisingly, the results of experiments with varying speeds demonstrated that the wear resistance increases as the speed increses up to a critical point from which onwards the resistance decreases. More over, the experimental results indicated that there is a lineer relation between the adhesive wear resistance and the hardness of the sample. The 5 ferrite and its pruducts a phase and M23C6 contribute to the hardness of the sample, thereby its wear resistance increases considerably. 2000,58 Pages
Benzer Tezler
- Nano bor tozu ile yüzeyi alaşımlandırılan östenitik paslanmaz çeliğin mekanik özellikler ve korozyon davranışının araştırılması
Investigation of mechanical properties and corrosion behavior of austenitic stainless steel the surface of which alloyed with nanoboron powder
ALİ GÜNEN
Doktora
Türkçe
2012
Metalurji MühendisliğiFırat ÜniversitesiMetalurji Eğitimi Ana Bilim Dalı
PROF. DR. NURİ ORHAN
- Termal sprey kaplama yöntemi ile seramik kaplanan östenitik paslanmaz çeliklerin mikroyapı ve mekanik özelliklerinin araştırılması
The investigation of microstructure and mechanical properties of austenitic stainless steels seramic coated with thermal spray coating method
ZELİHA AYDENİZ
Yüksek Lisans
Türkçe
2019
Metalurji MühendisliğiFırat ÜniversitesiMetalurji ve Malzeme Mühendisliği Teknolojileri Ana Bilim Dalı
DOÇ. DR. UĞUR ÇALIGÜLÜ
- Östenitik paslanmaz çeliğin bor katkılı Ni3Al ile kaplanabilirliğinin araştırılması
Investigation of boron doped Ni3Al coating of austenitic stainless stell
MEHMET AKKAŞ
Yüksek Lisans
Türkçe
2013
Metalurji MühendisliğiFırat ÜniversitesiMetalurji Eğitimi Ana Bilim Dalı
DOÇ. DR. SERMİN OZAN
- Kriyojenik işlemin AISI D3 soğuk iş takım çeliğinin performansına etkilerinin incelenmesi
Determining the effects cryogenic treatment on the performance of AISI D3 cold work steel
YUSUF ARSLAN
- AISI 304 paslanmaz çelik ile genel yapı çeliğinin sürtünme kaynak kabiliyetinin araştırılması
Investigation of friction weldability of AISI 304 stainless steel to structural steel
NİHAT KAYA
Yüksek Lisans
Türkçe
2010
Metalurji MühendisliğiGazi ÜniversitesiMetal Eğitimi Ana Bilim Dalı
DOÇ. DR. HAKAN ATEŞ