Geri Dön

Çeşitli elyaf dizilimleriyle oluşturulmuş metal köpük çekirdekli sandviç kompozitlerin mekanik davranışlarının incelenmesi

Investigation of mechanical behaviours of metal foam cored sandwich composites formed by various fiber orientations

  1. Tez No: 304912
  2. Yazar: EMRE KARA
  3. Danışmanlar: PROF. DR. HALİL AYKUL
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mühendislik Bilimleri, Mechanical Engineering, Engineering Sciences
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2012
  8. Dil: Türkçe
  9. Üniversite: Hitit Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 106

Özet

Sandviç kompozit üretimi ile elde edilen başarıların gün geçtikçe artması, bu tip malzemelere olan ilgiyi yoğunlaştırmıştır. Bu tezde, hafiflik ve mukavemet özelliklerinden dolayı tercih edilen sandviç kompozitler ve bu malzemelere yaygın olarak uygulanan mekanik test yöntemleri incelenmiştir. Bu çalışmanın amacı, yüzeyi çeşitli elyaf dizilimleriyle oluşturulmuş, alüminyum köpük ve alüminyum köpük sandviç (AKS) panel çekirdekli sandviç kompozitlerin mekanik davranışlarının deneysel olarak incelenmesidir.Sandviç kompozitlere yaygın olarak uygulanan mekanik test yöntemlerinden kenarına ve yüzeyine basma test yöntemleri, üç nokta eğilme test yöntemi ve düşük hızlı darbe test yöntemi uygulanmıştır. Her bir test yönteminin uygulama şekli ve test numuneleri gösterilerek, elde edilen grafikler sunulmuştur. Çalışmada, hafifliği yönüyle alüminyum köpük ve alüminyum köpük sandviç panel, çekirdek malzemeleri olarak kullanılmış ve bu köpükler hakkında detaylı bilgiler verilmiştir.Yapılan çalışmalar neticesinde sandviç kompozitlerin mevcut ağırlıklarına nazaran rijitlikleri ve mukavemetlerinin ne denli önemli olduğu gözlenmiştir. Benzer çalışmalarda kullanılan yüzey malzemeleri yerine bu çalışmada; tek eksenli dört kat [0o]2s, iki eksenli dört kat [0o/90o]2s, iki eksenli dört kat [45o/-45o] 2s, antisimetrik dizilimli iki eksenli dört kat [0o/90o]s/[45o/-45o]s ve simetrik dizilimli iki eksenli dört kat [0o/90o]s/[45o/-45o]s olmak üzere beş çeşit elyaf dizilimiyle cam elyaf malzemeleri epoksi reçine emdirilerek Cam Elyaf Takviyeli Plastik (CTP) oluşturulmuş ve CTP, bu epoksi reçine vasıtasıyla çekirdek malzemesi olan alüminyum köpüğe yapıştırılmıştır. Alüminyum köpük sandviç panel çekirdekli kompozitler için ise iki kat [0o/90o/Mat]s dizilimli cam elyaf ve farklı bir epoksi reçine kullanılarak CTP oluşturulmuş ve aynı reçine ile çekirdek malzemesine yapıştırılmıştır.Basma ve eğilme test yöntemleri sonucunda, farklı oryantasyon açılarında elde edilen gerilme-%uzama ve yük-sehim eğrileri ile düşük hızlı darbe deneyi sonucunda farklı hızlarda elde edilen yük-zaman ve yük-uzama eğrileri karşılaştırmalı olarak sunulmuştur.Anahtar Sözcükler; Sandviç Kompozitler, Alüminyum Köpük, Alüminyum Köpük Sandviç, CTP, Kenarına Basma Testi, Yüzeyine Basma Testi, Üç Nokta Eğilme Testi, Düşük Hızlı Darbe Testi

Özet (Çeviri)

Day by day increment of the successes which are obtained by sandwich composite production was focused on the interest on this kind of materials. In this thesis, the sandwich composites which are preferred because of their light weight and strength properties and the mechanical test methods which are commonly applied on these materials have been investigated. The aim of this study is to be investigated the mechanical behaviours of sandwich composites which have aluminium foam and aluminium foam sandwich panel cores and the faces formed by various fiber orientations.In the study, flatwise and edgewise compressive test methods, three point bending test method and low velocity impact test from mechanical test methods which are commonly applied on sandwich composites were applied. Application type and test specimen of every test method were shown, the curves obtained from the tests were presented. In the study, aluminum foam and aluminium foam sandwich panel were used because of its light weight and detailed information was given about these foams.According to the results of the studies, it was observed how much important their rigidity and strength versus their existing weight. In this study, instead of face materials used in similar studies; Glass Fiber Reinforced Plastic (GFRP) was constructed impregnating epoxy resin into fiber glass materials by five kinds of fiber orientation which are one axis and four layered [0o]2s, two axes and four layered [0o/90o]2s, two axes and four layered [45o/-45o] 2s, anti symmetrically orientated two axes and four layered [0o/90o]2s/[45o/-45o] 2s and symmetrically orientated two axes and four layered [0o/90o]2s/[45o/-45o] 2s and GFRP was bonded onto the aluminum foam core by this epoxy resin. GFRP was created by using two layered [0o/90o/Unidirectional]s fiber glass and different epoxy resin for aluminium foam sandwich panel it was bonded onto core material by using same epoxy.The obtained stress-strain and load-deflection curves at different orientation angles after compressive and bending test methods and the obtained load-time and load-deflection curves at different velocities after low velocity impact tests were reported comparatively.Key Words; Sandwich Composites, Aluminium Foam, Aluminium Foam Sandwich, GFRP, Edgewise Compressive Test, Flatwise Compressive Test, Three Point Bending Test, Low Velocity Impact Test

Benzer Tezler

  1. TiO2 nano partikül katkılı cam, aramid, karbon hibrit epoksikompozitlerin mekanik özellikleri

    Mechanical properties of TiO2 nanoparticle added glass, aramid,carbon hybrid epoxy composites

    HÜSEYİN ALPTEKİN

    Yüksek Lisans

    Türkçe

    Türkçe

    2022

    Makine MühendisliğiHarran Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    DOÇ. DR. MUSTAFA ÖZEN

  2. Eğrisel elyaflı katmanlı kompozit ince cidarlı kirişlerin mekanik davranışı

    Mechanical behavior of curvilinear fiber laminated composite thin walled beams

    MUHSİN GÖKHAN GÜNAY

    Doktora

    Türkçe

    Türkçe

    2018

    Makine MühendisliğiTrakya Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. TANER TİMARCI

  3. Development of vibration performances of hybrid laminated composite materials by using stochastic methods

    Tabakalı hibrit kompozit malzemelerin titreşim performanslarının stokastik optimizasyon yöntemleri kullanılarak geliştirilmesi

    MELİH SAVRAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2017

    Makine Mühendisliğiİzmir Katip Çelebi Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. LEVENT AYDIN

  4. Experimental determination and theoretical prediction of the acoustic properties of the jute and luffa bio-fiber materials

    Jute ve luffa bio-fiber malzemelerinin akustik özelliklerinin deneysel olarak tespiti ve teorik tahmini

    AHMET CİHAN ÖZCAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2021

    Makine Mühendisliğiİstanbul Teknik Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. KENAN YÜCE ŞANLITÜRK

    DOÇ. DR. HASAN KÖRÜK

  5. Elyaf takviyeli kompozit malzemelerde elyaf yönü, boyu ve çapının mekanik özelliklere etkisinin bilgisayar yardımı ile incelenmesi

    Başlık çevirisi yok

    NİLHAN BEYLİKÇİ

    Yüksek Lisans

    Türkçe

    Türkçe

    1994

    Makine MühendisliğiTrakya Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    Y.DOÇ.DR. VURAL CEYHUN