Geri Dön

İzod metodunda beton numune boyutunun çarpma dayanımına etkisi

Effect of impact strength of concrete sample size in izod method

  1. Tez No: 355516
  2. Yazar: ZAFER KOCALMIŞ
  3. Danışmanlar: YRD. DOÇ. DR. ERDİNÇ ARICI
  4. Tez Türü: Yüksek Lisans
  5. Konular: İnşaat Mühendisliği, Civil Engineering
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2014
  8. Dil: Türkçe
  9. Üniversite: Fırat Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Yapı Eğitimi Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 73

Özet

Beton ve betonarme elemanlar kullanım yerlerine göre farklı etkilere maruz kalırlar. Bu etkilerden basınç ve çekme kuvvetlerine karşı betonun davranışı üzerine birçok araştırma yapılmış olmasına karşın betonda çarpma dayanımı etkileri yeterince araştırılmamıştır. Betonarme yapıların etkisi altında kaldığı, davranışı en az bilinen yükleme tipi çarpma yüklemesidir. Bu çalışmada numune boyutunun betonun çarpma dayanımına etkisi incelenmiştir. Bu amaç doğrultusunda, çarpma mukavemetinin belirlenmesi için yapılan deneylerde max. agrega çapı 16 mm. olan, üç farklı a/D oranına (0,1-0,2 ve 0,3) ve iki farklı L/D oranına (2,5 ve 4) sahip 6 seri numune hazırlanmıştır. Hazırlanan her serideki numunelerin basınç, eğilmede çekme, yarmada çekme ve çarpma dayanımlarının belirlenmesi için deneyler yapılmıştır. Deneyler sonucunda, faydalı kesit alanı azaldıkça numunenin kırılması için gereken enerjinin azaldığı, arttıkça da kırılması için gereken enerjinin arttığı görülmüştür.

Özet (Çeviri)

Concrete and reinforced concrete elements are exposed to different effects according to place of use. A lot of researches have been done for some of these effects like the behaviors of concrete against the compressive and tensile forces but the effect of impact resistance has not been investigated sufficiently. The least well known loading type is the impact loading that are affecting on to RC structures. In this study, it was investigated the effect sample of support spacing and size of sample to concrete of impact strength. At carried out tests to determine of impact resistance, 6 series specimens has prepared that they has got max. aggregate size 16 mm and three different a/D ratios (0,1-0,2 and 0,3) and two different L/D ratios (2,5 and 4). There were some experiments for determining the compressive strength, strength of flexural, strength of splitting and strength of impact for the prepared samples. As a result of experiments, it was observed that with decreasing of the useful cross-sectional area the energy required to break the sample was decreased and with increasing of the size of the area energy required to break was increased .

Benzer Tezler

  1. El yatırma yöntemi ile elyaf takviyeli kompozit yapıların üretilmesi ve özellikleri

    Production of fibre reinforced composite structures and their properties by the hand lay-up method

    HÜROL YÖNEY

    Yüksek Lisans

    Türkçe

    Türkçe

    2007

    Tekstil ve Tekstil MühendisliğiMarmara Üniversitesi

    Teknoloji Eğitimi Ana Bilim Dalı

    YRD. DOÇ. DR. SEVHAN MÜGE YÜKSELOĞLU

  2. Yünlü atık kumaş takviyeli kompozitler

    Reinforced composites of waste wool fabric

    MAHİR ÇALIŞKAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2011

    Tekstil ve Tekstil MühendisliğiMarmara Üniversitesi

    Tekstil Eğitimi Ana Bilim Dalı

    DOÇ. DR. S. MÜGE YÜKSELOĞLU

  3. Biyolojik ve sentetik hidroksiapatit (HA) takviyeli polilaktik asit (PLA) ve polipropilen (PP) polimer kompozitinin hazırlanışı, karakterizasyonu ve vücuda uyumluluklarının incelenmesi

    Preparation, characterization and body compatibilty of biological and synthetic hydroxyapatite reinforced polylactic acid (PLA) and polypropylene (PP) biocomposite

    İSMAİL HAKKI KENET

    Yüksek Lisans

    Türkçe

    Türkçe

    2016

    Metalurji MühendisliğiMarmara Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. MÜNİR TAŞDEMİR

  4. EPDM atıklarının otomotiv endüstrisinde değerlendirilmesi üzerine bir inceleme

    An investigation into the reusability of EPDM wastes in automotive industry

    KEMAL ÜNLÜ

    Yüksek Lisans

    Türkçe

    Türkçe

    2007

    Polimer Bilim ve TeknolojisiMarmara Üniversitesi

    Makine Eğitimi Ana Bilim Dalı

    YRD. DOÇ. DR. HALİL DEMİRER

  5. IZOD darbe testi cihazının tasarımı ve plastik testlerinde kullanılması

    Designing of IZOD impact test instrument and using for the plastic testing

    ENES ALPEREN ASLAN

    Yüksek Lisans

    Türkçe

    Türkçe

    2022

    Polimer Bilim ve TeknolojisiHacettepe Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    PROF. DR. MURAT ŞEN