Büyük çaplı kelebek vanalarda disk üzerindeki gerilme dağılımının sayısal olarak belirlenmesi ve disk geometrisi tasarımı
CFD analysis and shape design of large diameter butterfly valve
- Tez No: 384911
- Danışmanlar: YRD. DOÇ. DR. LEVENT ALİ KAVURMACIOĞLU
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2014
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Isı-Akışkan Bilim Dalı
- Sayfa Sayısı: 81
Özet
Bu çalışmada, kelebek vana disk geometrisinin optimizasyonu için akış yapı etkileşimi metodundan faydalanılacaktır. Basit bir disk geometrisi alınarak, kapağın değişik açıklık dereceleri için sayısal çözümleme yapılarak disk üzerine etkiyen hidrodinamik momentin en fazla olduğu, dolayısıyla gerilmenin en tehlikeli olduğu açıklık pozisyonu tespit edilecektir. Disk üzerinde oluşan gerilme dağılımı, sayısal akışkanlar mekaniği yöntemleri ile belirlenecek olarak akış alanı hesaplanması sonucu elde edilen basınç ve kayma gerilmelerinin akış yapı etkileşimi metodu ile disk geometrisi üzerine uygulanması ile elde edilecektir. En tehlikeli disk açıklığının belirlenmesinden sonra, bu açıklık pozisyonu için disk geometrisi üzerinde konstrüktif değişiklikler yapılarak (kafes geometri) disk ağırlığının ve disk üzerine gelen gerilmelerin azaltılması sağlanacaktır. Bu değişiklerin akış alanına ve gerilme dağılımına etkisi irdelenecektir. Ayrıca, Turgut Sarpkaya[6]'nın geliştirdiği ve kelebek vanaların moment ile kavitasyon karakteristiklerini incelediği analitik yöntem kullanılarak sayısal ve analitik çözümlerin sonuçlarının, deney sonuçları ile uyumu irdelenecektir.
Özet (Çeviri)
Butterfly valves are in use at petroleum, chemical industry, metallurgy, electric power, water supply, etc. There are widely different operating conditions and butterfly valve sizes. Valve diameters vary from 5 centimeters up to 5 meters. In the study, effects of different parameters on large-diameter (2 m) butterfly valve performance will ve investigated. Important design topics of butterfly valves are torque, cavitation and head loss. Torque is a remarkable issue in butterfly valve design. It is important because disc material, actuator type, disc thickness, disc geometry and shaft position. There is several torque components as bearing torque, center of gravity torque, hydrostatic torque, seating torque, dynamic torque and packing torque. The most important part of torque is dynamic torque, because when the valve is opened, it reaches significant values and affects total torque. There is also a different parameter that affects the torque. Experiments show that if the valve shafted eccentrically as the shaft centerline is quite above the disc centerline, then total torque is minimum. Therefore, the vertical distance between shaft and disc center is also an important parameter for design and analysis of butterfly valve. Head loss is another important consideration with respect to energy costs. If the head loss increases, then energy costs increases. The most common two parameter in head loss calculations are Cv and Kv. There is also a different flow coefficient Cd definition which is advantageous because it is always varies from 0 to 1 with different opening positions of valve and it is easy to show the analysis and modeling results. Cavitation can be occur when the local static pressure decreases below the vaporization pressure at operate temperature. The cavitation index σ term is used to predict cavitation. Cavitation index is also a dimensionless parameter. Valve charasteristics are determined and shown by using Kv - % opening and Cv - % opening curves, so to obtain valve characteristics, Kv and Cv values must be calculated for different opening positins. To calculate flow coefficient and valve resistance coefficient, ΔP and Q or V values must be measured. These values can be also obtained by using CFD analysis. There is another method which firstly used by Sarpkaya, Helmholtz's free streamline theory. The theory gives also satisfactory results. In this study, experimental, theoretical and CFD ressults were compared and discussed.
Benzer Tezler
- Experımental analysıs of the performance coefficients of the butterfly valves
Kelebek vanalarda performans katsayılarının deneysel olarak incelenmesi
MEHMET SANDALCI
Yüksek Lisans
İngilizce
2009
Makine MühendisliğiMarmara ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ. DR. KURTUL KÜÇÜKADA
YRD. DOÇ. DR. EBRU MANÇUHAN
- Üstat Hüsamettin Yıldırım ve itikadi görüşleri
Üstat Hüsamettin Yıldırım and its views
SİBEL ÜNLÜ
Yüksek Lisans
Türkçe
2021
Dinİnönü ÜniversitesiTemel İslam Bilimleri Ana Bilim Dalı
PROF. DR. FİKRET KARAMAN
- Investigation of mechanical properties of yarns and fabrics produced naturally coloured cotton fibers
Doğal olarak yetiştirilmiş renkli pamuktan üretilen iplik ve kumaşların fiziksel özelliklerinin incelenmesi
NAZAN AVCIOĞLU
Yüksek Lisans
İngilizce
2003
Tekstil ve Tekstil MühendisliğiGaziantep ÜniversitesiTekstil Mühendisliği Ana Bilim Dalı
PROF. DR. ALİ KİREÇCİ
- Büyük çaplı veri zarflama analizi modelleri için yeni yaklaşımlar
New approaches for large scale DEA data sets
GAZİ BİLAL YILDIZ
Yüksek Lisans
Türkçe
2013
Endüstri ve Endüstri MühendisliğiErciyes ÜniversitesiEndüstri Mühendisliği Ana Bilim Dalı
DOÇ. DR. BANU SOYLU
- Büyük çaplı fiber optik kabloların ekstrüzyon yöntemi ile üretim teknolojilerinin geliştirilmesi
Enhancement of manufacturing technology of fiber optic cables with high diameter by using extrusion production method
OSMAN ÖZDAMAR
Yüksek Lisans
Türkçe
2011
Makine MühendisliğiSakarya ÜniversitesiMakine Eğitimi Ana Bilim Dalı
YRD. DOÇ. DR. MESUT DURAT
YRD. DOÇ. DR. AHMET DEMİRER