Geri Dön

Öngerilimli karbon elyaf takviyeli kompozit üretimi için sistem tasarımı, imalatı ve kompozit malzeme üretimi

System design and production for prestressed carbon fiber reinforced composite and the production of composite materials

  1. Tez No: 431090
  2. Yazar: ÖMER BAYRAKTAR
  3. Danışmanlar: DOÇ. DR. ABDULMECİT GÜLDAŞ
  4. Tez Türü: Yüksek Lisans
  5. Konular: Mühendislik Bilimleri, Polimer Bilim ve Teknolojisi, Engineering Sciences, Polymer Science and Technology
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2016
  8. Dil: Türkçe
  9. Üniversite: Gazi Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: İmalat Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 107

Özet

Geleneksel yöntemlerde örülmüş fiberlerden elde edilen kompozit malzemelerin şekillendirilmesinde fiber sarma yöntemi hariç tüm tekniklerde, fiber kumaş bir yüzeye yatırılarak şekillendirilmektedir. Serbest elle yüzeye yatırma yönteminde kompozit malzeme içerisinde homojen olmayan fiber dağılımı meydana gelebilmektedir. Bu sebepten dolayı kompozit üzerine yük uygulandığında uygulanan kuvvet tüm fiberlere eşit oranda dağılmamaktadır. Bu durum, kompozit malzemenin, beklenilen mekanik özelliklerinin altında bir mekanik özelliğe sahip olmasına sebep olmaktadır. Gerçekleştirilen çalışmada karbon fiber kumaş, bu çalışmada tasarlanan ve imalatı gerçekleştirilen gerdirme aparatı yardımıyla gerdirilmiştir. Gerdirme aparatının tasarımı detaylı olarak anlatılmıştır. Çalışmada 0 N, 200 N, 300 N, 450 N, 680 N, 1000 N olmak üzere altı farklı öngerilim değerleri araştırılmıştır. Deney sonuçlarının kararlı olması için her öngerilim değeri için iki adet plaka üretilmiş ve her plakadan 0°, 45° ve 90° yönlerde ikişer adet numune kesilmiştir. Bu metotla gerdirilen fiberler hem matris içerisinde homojen olarak dağılmış hem de tüm fiberler belirli bir doğrultuda doğrusallığı sağlanmıştır. Çekme testi deneylerinden elde edilen verilere göre, en iyi çekme dayanımının dokuma şeklindeki kumaşın 4,09 MPa öngerilim ile şekillendirilmesi sonucu elde edilmiştir. Bu öngerilim değerinde kompozit malzemenin kopma dayanımı 1169 Mpa'dan %40 artarak 1629 MPa değerine çıkmıştır. Bu öngerilim değerinden daha yüksek değerlerde iyi ıslanma sağlanamadığı için mukavemet değerlerinin azaldığı gözlenmiştir.

Özet (Çeviri)

In shaping composite materials that are obtained from traditionally woven fibers, except for filament winding method, all the techniques are carried out by laying the fiber fabric on a surface and then shaping it. In the products produced with the method of laying fabric layers on a surface, a non-uniform structure between fiber and matrix material may occur. Long fibers that are laid freely cannot be placed in matrix material lineally. Therefore, when pressure is (loads are) applied on the composite, force is not distributed to all fibers evenly. This situation results in lower mechanical features for composite material than expected. In this thesis, woven fabrics produced from the fibers are formed by stretching fabric instead of laying on a surface freely. This stretching process will be performed by a stretching tool that was designed and manufactured within this project. The design of stretching apparatus is described in detail. To investigate the effects of prestress, six different values (0N, 200N, 450N, 680N, 1000N) were used. Two plates were produced for every prestress value and each plate was cut into 2 samples in the direction of 0°, 45°and 90°. With the use of this method, fibers will be both homogeneously dispersed and linearized in a certain direction in the matrix. According to the contained data from tension test experiments, the highest tensile strength was observed on a 4,09 MPa pretension value. At this pretension value, the composite material's ultimate strength was increased 40% from 1169 MPa to 1629 MPa. The strength value decreased on higher pretension values due to the insufficient wettability.

Benzer Tezler

  1. Cathodic hydrogen emrittlement of pre-stressing steel wires in simulated generele enviroments

    Özellikleri beton'a benzer çözeltiler içinde ön gerilmeli çelik çubukların katodik hidrojenle gevrekleşmeleri

    SAMİ MASADEH

    Doktora

    İngilizce

    İngilizce

    1996

    Metalurji MühendisliğiOrta Doğu Teknik Üniversitesi

    Metalurji Mühendisliği Ana Bilim Dalı

    PROF. DR. MUSTAFA DORUK

  2. Öngerilmeli beton köprü kirişlerinin yapısal onarımı

    Structural repair of prestressed concrete bridge beams

    BÜLENT PEKYER

    Yüksek Lisans

    Türkçe

    Türkçe

    2010

    İnşaat Mühendisliğiİstanbul Teknik Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DOÇ. DR. TURGUT ÖZTÜRK

  3. Bias voltage control of a molecular spin valve

    Bir moleküler spin süzgecinin öngerilim voltajı ile kontrolü

    DUYGU CAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2009

    Fizik ve Fizik Mühendisliğiİhsan Doğramacı Bilkent Üniversitesi

    Fizik Bölümü

    DOÇ. DR. RAMAZAN TUĞRUL SENGER

    PROF. DR. SALİM ÇIRACI

  4. Karbon – fiber donatıyla öngerilmesiz monoblok demiryolu beton traversi geliştirilmesi

    New railway concrete sleeper research about using carbon fiber reinforced polymer rebars with non-prestressed and mono-block process

    FERHAT ÇEÇEN

    Yüksek Lisans

    Türkçe

    Türkçe

    2019

    İnşaat MühendisliğiTokat Gaziosmanpaşa Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ FERİT YAKAR

  5. Demiryolu traverslerinde yerli lamine cfrpu donatı kullanımının deneysel ve sayısal incelenmesi

    Experimental and numerical investigation of the use of domestic laminated cfrpu reinforcement in railway sleepers

    FERHAT ÇEÇEN

    Doktora

    Türkçe

    Türkçe

    2023

    UlaşımErciyes Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    PROF. DR. BEKİR AKTAŞ