Rüzgar tünelinde bilgisayarla balans değerleri
Computer aided balance experiments in wind tunnels
- Tez No: 46591
- Danışmanlar: DOÇ.DR. M. ADİL YÜKSELEN
- Tez Türü: Yüksek Lisans
- Konular: Uçak Mühendisliği, Aircraft Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 1995
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 90
Özet
For incompressible flow, Ap"o = -pU2 eB. Corrections to model quantities: ACA = -(2-M2)CAeB, Where Ca is a non-dimensional force and moment coefficients other than drag coefficients Co. For two-dimensional airfoils: ACD = -[ (1 + 0.4M2) es + (2 - M2) eB] CD. For three-dimensional models: ACD = -(1 + 0.4M2) es Coo - (2 - M2) eB CD. In both cases: ACp = [2-(2-M2)Cp]eB Data-Acquisition In this method, a computer and special data-acquisition cards controlled from this computer are used. The wind tunnel balances is connect this card with a proper signal amplifier to obtain a true level of signal. And the aid of computer programs the all process including calibration, making experiments, controlling models inside wind tunnel, and obtain and analyze aerodynamics forces and moment coefficients. By the use of data-acquisition system, also we can short the time period of experiment and calibration process. While doing experiment, all data that comes from wind tunnel balances through the data-acquisition card, are the electrical signal and they transform to integer values between -2047 and 2048 or 0 and 4096 by this system in real time or using DMA access. When the first, integer values could be obtained, any can be able to any operation on this data by computer program easily. RPV's Wind Tunnel Tests Testing of RPV in wind tunnel is considered as a proof of wind tunnel test system and also RPV's aerodynamic coefficients were needed to be obtained. The 1/6 scaled of real RPV's was chosen because of blockage affects and prototype of RPV's was made from composite materials. xvn
Özet (Çeviri)
While experiments, wind tunnel velocity was calculated from pressure manometer that works Bernoulli principle; PT = Ps + q, Here q is dynamic pressure and equivalent of i-pU2. While experiments dynamic pressure is read from“U”manometer of which inlet is in entrance room, outlet is in test section. Of course a proper exchange must be apply because reading values are mm Water or mmAlcohol. Ambient temperature and pressure also must be measure while experiments. Results Results of wind tunnel testing have been analyzed by use of computer program and obtained all needed coefficients as both tables and graphics. According to these results, designing of RPV will continue with some changes. But more important result about the experimental system is that it is more practical, efficient and works truly. xvmFor incompressible flow, Ap“o = -pU2 eB. Corrections to model quantities: ACA = -(2-M2)CAeB, Where Ca is a non-dimensional force and moment coefficients other than drag coefficients Co. For two-dimensional airfoils: ACD = -[ (1 + 0.4M2) es + (2 - M2) eB] CD. For three-dimensional models: ACD = -(1 + 0.4M2) es Coo - (2 - M2) eB CD. In both cases: ACp = [2-(2-M2)Cp]eB Data-Acquisition In this method, a computer and special data-acquisition cards controlled from this computer are used. The wind tunnel balances is connect this card with a proper signal amplifier to obtain a true level of signal. And the aid of computer programs the all process including calibration, making experiments, controlling models inside wind tunnel, and obtain and analyze aerodynamics forces and moment coefficients. By the use of data-acquisition system, also we can short the time period of experiment and calibration process. While doing experiment, all data that comes from wind tunnel balances through the data-acquisition card, are the electrical signal and they transform to integer values between -2047 and 2048 or 0 and 4096 by this system in real time or using DMA access. When the first, integer values could be obtained, any can be able to any operation on this data by computer program easily. RPV's Wind Tunnel Tests Testing of RPV in wind tunnel is considered as a proof of wind tunnel test system and also RPV's aerodynamic coefficients were needed to be obtained. The 1/6 scaled of real RPV's was chosen because of blockage affects and prototype of RPV's was made from composite materials. xvnWhile experiments, wind tunnel velocity was calculated from pressure manometer that works Bernoulli principle; PT = Ps + q, Here q is dynamic pressure and equivalent of i-pU2. While experiments dynamic pressure is read from ”U“ manometer of which inlet is in entrance room, outlet is in test section. Of course a proper exchange must be apply because reading values are mm Water or mmAlcohol. Ambient temperature and pressure also must be measure while experiments. Results Results of wind tunnel testing have been analyzed by use of computer program and obtained all needed coefficients as both tables and graphics. According to these results, designing of RPV will continue with some changes. But more important result about the experimental system is that it is more practical, efficient and works truly. xvmFor incompressible flow, Ap”o = -pU2 eB. Corrections to model quantities: ACA = -(2-M2)CAeB, Where Ca is a non-dimensional force and moment coefficients other than drag coefficients Co. For two-dimensional airfoils: ACD = -[ (1 + 0.4M2) es + (2 - M2) eB] CD. For three-dimensional models: ACD = -(1 + 0.4M2) es Coo - (2 - M2) eB CD. In both cases: ACp = [2-(2-M2)Cp]eB Data-Acquisition In this method, a computer and special data-acquisition cards controlled from this computer are used. The wind tunnel balances is connect this card with a proper signal amplifier to obtain a true level of signal. And the aid of computer programs the all process including calibration, making experiments, controlling models inside wind tunnel, and obtain and analyze aerodynamics forces and moment coefficients. By the use of data-acquisition system, also we can short the time period of experiment and calibration process. While doing experiment, all data that comes from wind tunnel balances through the data-acquisition card, are the electrical signal and they transform to integer values between -2047 and 2048 or 0 and 4096 by this system in real time or using DMA access. When the first, integer values could be obtained, any can be able to any operation on this data by computer program easily. RPV's Wind Tunnel Tests Testing of RPV in wind tunnel is considered as a proof of wind tunnel test system and also RPV's aerodynamic coefficients were needed to be obtained. The 1/6 scaled of real RPV's was chosen because of blockage affects and prototype of RPV's was made from composite materials. xvnWhile experiments, wind tunnel velocity was calculated from pressure manometer that works Bernoulli principle; PT = Ps + q, Here q is dynamic pressure and equivalent of i-pU2. While experiments dynamic pressure is read from“U”manometer of which inlet is in entrance room, outlet is in test section. Of course a proper exchange must be apply because reading values are mm Water or mmAlcohol. Ambient temperature and pressure also must be measure while experiments. Results Results of wind tunnel testing have been analyzed by use of computer program and obtained all needed coefficients as both tables and graphics. According to these results, designing of RPV will continue with some changes. But more important result about the experimental system is that it is more practical, efficient and works truly. xvmFor incompressible flow, Ap“o = -pU2 eB. Corrections to model quantities: ACA = -(2-M2)CAeB, Where Ca is a non-dimensional force and moment coefficients other than drag coefficients Co. For two-dimensional airfoils: ACD = -[ (1 + 0.4M2) es + (2 - M2) eB] CD. For three-dimensional models: ACD = -(1 + 0.4M2) es Coo - (2 - M2) eB CD. In both cases: ACp = [2-(2-M2)Cp]eB Data-Acquisition In this method, a computer and special data-acquisition cards controlled from this computer are used. The wind tunnel balances is connect this card with a proper signal amplifier to obtain a true level of signal. And the aid of computer programs the all process including calibration, making experiments, controlling models inside wind tunnel, and obtain and analyze aerodynamics forces and moment coefficients. By the use of data-acquisition system, also we can short the time period of experiment and calibration process. While doing experiment, all data that comes from wind tunnel balances through the data-acquisition card, are the electrical signal and they transform to integer values between -2047 and 2048 or 0 and 4096 by this system in real time or using DMA access. When the first, integer values could be obtained, any can be able to any operation on this data by computer program easily. RPV's Wind Tunnel Tests Testing of RPV in wind tunnel is considered as a proof of wind tunnel test system and also RPV's aerodynamic coefficients were needed to be obtained. The 1/6 scaled of real RPV's was chosen because of blockage affects and prototype of RPV's was made from composite materials. xvnWhile experiments, wind tunnel velocity was calculated from pressure manometer that works Bernoulli principle; PT = Ps + q, Here q is dynamic pressure and equivalent of i-pU2. While experiments dynamic pressure is read from ”U" manometer of which inlet is in entrance room, outlet is in test section. Of course a proper exchange must be apply because reading values are mm Water or mmAlcohol. Ambient temperature and pressure also must be measure while experiments. Results Results of wind tunnel testing have been analyzed by use of computer program and obtained all needed coefficients as both tables and graphics. According to these results, designing of RPV will continue with some changes. But more important result about the experimental system is that it is more practical, efficient and works truly. xvm
Benzer Tezler
- Automation and verification of Ankara Wind Tunnel
Ankara Rüzgar Tüneli'nin otomasyonu ve doğrulama testleri
ARGÜN KATIRCI
Yüksek Lisans
İngilizce
2006
Havacılık MühendisliğiOrta Doğu Teknik ÜniversitesiHavacılık ve Uzay Mühendisliği Ana Bilim Dalı
PROF.DR. NAFİZ ALEMDAROĞLU
- The effects of exterior shading devices on flow mechanisms of building façade
Bina yüzeylerinde gölgeleme elemanlarının akış mekanizmalarına etkileri
ELİF ALTUNTAŞ
Yüksek Lisans
İngilizce
2007
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
Y.DOÇ.DR. MURAT ÇAKAN
- Experimental and numerical investigation of the wind effects on long span bridge decks
Uzun açıklıklı açıklık köprü güverteleri üzerindeki rüzgar etkisinin deneysel ve sayısal incelenmesi
IMAN ASHTİANİ ABDİ
Yüksek Lisans
İngilizce
2011
Havacılık MühendisliğiOrta Doğu Teknik ÜniversitesiHavacılık ve Uzay Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. OĞUZ UZOL
YRD. DOÇ. DR. ÖZGÜR KURÇ
- İki boyutlu yapısal olmayan ağların adaptasyonu
Adaptive remeshing on two dimensional unstructured meshes
SERDAR DİLAVER
- Eksenel fan ve ısı kuyusu barındıran bir soğutma sisteminde hava akışının iyileştirilmesi
Improvement of the air flow in a cooling system including axial fan and heat sink
EREN ABACI
Yüksek Lisans
Türkçe
2018
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. SEYHAN ONBAŞIOĞLU