Geri Dön

Nonwoven polyolofin ve doğal keten/jüt takviyeli hibrit kompozitlerde iki farklı nonwoven üretim yönteminin malzemenin mekanik özelliklerine etkisi

Effect of two different nonwoven manufacturing method on mechanical properties of nonwoven polyolofin and natural flax/jute reinforced hybrid composites

  1. Tez No: 611273
  2. Yazar: UĞUR ÖMER KOCAMIŞ
  3. Danışmanlar: DOÇ. DR. SAMİ SAYER
  4. Tez Türü: Yüksek Lisans
  5. Konular: Mühendislik Bilimleri, Engineering Sciences
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2019
  8. Dil: Türkçe
  9. Üniversite: Ege Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Malzeme Bilimi ve Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Malzeme Bilimi ve Mühendisliği Bilim Dalı
  13. Sayfa Sayısı: 123

Özet

Bu çalışmada doğal lif takviyeli hibrit kompozitlerin mekanik özellikleri üzerinde hibrit liflerin ve matris malzemesi olan nonwoven kumaşların farklı üretim yöntemi ile imal edilmiş olmasının etkisinin analizine odaklanmıştır. Doğal hibrit takviyeli ve polimer matrisli kompozit numuneler üretilerek mekanik özellikleri incelenmiştir. Takviye elemanları olarak jüt ve keten kumaşları kullanılırken, matris elemanı olarak polietilen (PE) film ve polipropilen (PP) nonwoven kumaşlar seçilmiştir. Polipropilen nonwoven kumaşların üretim yöntemleri meltblown ve spunbond olarak farklı iki kategoriden seçilmiştir. Deney sonuçlarının sağlamasını daha güvenilir yapmak adına farklı yoğunluk seviyelerindeki nonwoven kumaşlar kullanılarak deney farklı seviyelerde mukayese edilmiştir ve ayrıca farklı kütle/alan özelliğine sahip nonwoven kumaşların da kompozit malzemeye olan etkisi incelenmiştir. Jüt ve keten kumaşlarının yüzeyi, matrisi ile uyumluluğu arttırmak için alkali işlemle modifiye edilmiştir. Hibrit kompozitleri karakterize etmek için ASTM ve DIN standartlarına göre deneysel çekme, eğilme ve darbe testleri yapılmıştır. Son olarak, test edilen numunelerin kırılma yüzeyini incelemek için bir taramalı elektron mikroskobu (SEM) kullanılmıştır. Bulgular üretilen kompozit numunelerin saf HDPE ile kıyaslandığında dayanımı arttırtığını göstermektedir. Fakat kompozit numunelerin kendi içersinde kıyaslanması, Spunbond yöntemi ile üretilen nonwoven yüzeyli hibrit kompozitlerin Meltblown ile üretilenlerden daha mukavim olduğu ve sonuçlarının daha stabil olduğunu ortaya koymaktadır. Ayrıca gramaj farkının SB numunelerinde ters orantılı bir etkiye sebep olduğu, MB numunelerinde ise ayırt edici bir özellik olmadığı gözlemlenmiştir.

Özet (Çeviri)

The present study is focused on the analysis of the effect of hybridization and the effect of two different manufacturing methods for nonwoven polymer matrix on the mechanical properties of natural fiber-reinforced hybrid composites. Natural fiber-reinforced hybrid composite samples with polymer matrix were manufactured and mechanical properties were investigated. Reinforcement materials were jute and flax, matrix polymers were polyethylene films and nonwovens made of polypropylene. PP nonwovens were manufactured by two different method which were meltblown and spunbond. Several densities of nonwovens were used for reliable experiment results and also effect of different mass/area ratio nonwovens on mechanical properties of composite material was investigated. The surface of jute and flax reinforcements has been modified by alkali treatment in order to enhance the compatibility with the matrix. Experimental tensile, flexural and impact tests were performed according to ASTM and DIN standards to characterize the new intralaminar hybrid composites. Finally, a scanning electron microscopy (SEM) was used to examine the fracture surface of the tested specimens. The results indicates that the composite samples increase the strength compared to pure HDPE. However, the comparison of composite samples among themselves shows that hybrid composites by Spunbond nonwoven method are more durable and stable than those produced by Meltblown. In addition, it was observed that the weight difference caused an inversely proportional effect in the SB samples, but it was not a distinguishing feature in the MB samples.

Benzer Tezler

  1. Ağır katmanların akustik performanslarının iyileştirilmesi

    Development of heavy layer' s acoustic performance

    UMUT BURAK DALBUDAK

    Yüksek Lisans

    Türkçe

    Türkçe

    2018

    Mühendislik Bilimleriİstanbul Üniversitesi

    Mühendislik Bilimleri Ana Bilim Dalı

    PROF. DR. ŞAH İSMAİL KIRBAŞLAR

  2. Production of microporous polypropylene breathable films

    Mikro gözenekli polipropilen nefes alabilen film üretimi

    JALE FİLİZ

    Yüksek Lisans

    İngilizce

    İngilizce

    2018

    Polimer Bilim ve Teknolojisiİstanbul Teknik Üniversitesi

    Polimer Bilim ve Teknolojisi Ana Bilim Dalı

    PROF. DR. NİLGÜN KIZILCAN

  3. Modern yol inşaatında geotekstil ve geodrit uygulaması konularında araştırma

    A Research on utilization of geotextile and geodrid in modern road construction

    İSKENDER MELİH AKSOY

    Yüksek Lisans

    Türkçe

    Türkçe

    1993

    İnşaat Mühendisliğiİstanbul Teknik Üniversitesi

    PROF.DR. REMZİ ÜLKER

  4. Melt-spinning and properties of soy-filled polyethylene, polypropylene, and poly-(Lactic acid) fibers

    Başlık çevirisi yok

    ÖZGÜN GÜZDEMİR

    Doktora

    İngilizce

    İngilizce

    2019

    Kimya MühendisliğiClemson University

    Kimya Mühendisliği Ana Bilim Dalı

    PROF. DR. DANIŞMAN YOK