Geri Dön

LED ile ısı uygulamasının geleneksel yapıştırıcı cam iyonomer simanların mekanik özellikleri üzerine etkisi

The effect of LEDapplication on the mechanical properties of different conventional luting glass ionomer cements

  1. Tez No: 624598
  2. Yazar: BUŞRA UYSAL
  3. Danışmanlar: YRD. DOÇ. BEYZA BALLI AKGÖL
  4. Tez Türü: Diş Hekimliği Uzmanlık
  5. Konular: Diş Hekimliği, Dentistry
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2016
  8. Dil: Türkçe
  9. Üniversite: İstanbul Medipol Üniversitesi
  10. Enstitü: Diş Hekimliği Fakültesi
  11. Ana Bilim Dalı: Çocuk Diş Hekimliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 84

Özet

Cam iyonomer simanlar dolgu malzemesi, yapıştırma ajanı ve kaide maddesi olarak çocuk diş hekimliğinde geniş kullanım alanına sahiptir. Cam iyonomer simanların mekanik özelliklerini geliştirebilmek için günümüze kadar pek çok modifikasyon yapılmaktadır. Son zamanlarda çalışmalar geleneksel cam iyonomer simanların en büyük dezavantaj olan nem hassasiyetinin önüne geçebilmek için materyale dışarıdan ısı verilmesi üzerine yoğunlaşmaktadır. Bu çalışmanın amacı, çocuk diş hekimliğinde yer tutucu apareylerin bantlarını simante etmek için kullanılan geleneksel yapıştırıcı cam iyonomer simanlara sertleşme esnasında LED ile ısı uygulamasının mekanik özellikleri üzerine etkisini in-vitro olarak değerlendirmektir. Çalışmada Ketac Cem Radiopaque (3M ESPE, St. Paul, Minnesota, Amerika), Meron(VOCO, Cuxhaven, Almanya) ve Kavitan Cem (Spofadental, Markova, Çek Cumhuriyeti) marka geleneksel yapıştırıcı cam iyonomer simanlar, ısı kaynağı olarak 1200mW/cm2 ışık yoğunluğuna sahip Elipar S10(3M ESPE) LED ışık cihazı kullanıldı. Basma dayanımı testi için 6mm yüksekliğe 4mm genişliğe sahip teflon kalıp, çapsal çekme dayanım testi için ise 3mm yüksekliğe 6 mm genişliğe sahip metal kalıp hazırlandı. Materyaller ısı uygulanmayan kontrol grubu, 60 saniye ve 90 saniye LED ile ısı uygulanan çalışma grupları olmak üzere üç alt gruba ayrıldı (n=10). Isı uygulaması, 'yönlendirilmiş sertleşme' gerçekleşmesi için kalıba yerleştirilen simanların sertleşmesi esnasında uygulandı. Mekanik dayanıklılık testleri geleneksel cam iyonomer simanların sertleşme süresi bitiminden 24 saat sonra yapıldı. Elde edilen verilerin değerlendirilmesinde İki Yönlü ANOVA testi kullanıldı. Devam testleri olarak Tek Yönlü ANOVA testi ve post hoc değerlendirmelerinde Tukey HSD test ve/veya Tamhane's T2 test kullanıldı. Anlamlılık p

Özet (Çeviri)

Glass ionomer cements have wide range of applications as filling material, bonding agent and base material in pediatric dentistry. Until today, many modifications have been made to improve the mechanical properties of glass ionomer cements. Recent studies have focused on external heat application to prevent moisture sensitivity, which is the biggest drawback of the conventional glass ionomer cements. The purpose of this study was to evaluate the application of heat with a LED lamb during curing on the mechanical properties of conventional luting glass ionomer cements, which used in cementation of spacemaintainers in pediatric dentistry. In this study, Ketac Cem Radiopaque (3M ESPE , St. Paul, Minnesota , USA), Meron (VOCO, Cuxhaven, Germany) and Kavitan Cem (Spofadental, Markov, Czech Republic) luting glass ionomer cements, as a heat source LED light curing unit Elipar s10 (3M ESPE) with light intensity of 1200mW/cm2 was used. For compressive strength test, samples were prepared in teflon molds with 6mm in depth, 4mm in diameter and for the diametral tensile strength test samples were prepared in metallic molds with 3 mm in depth, 6 mm in diameter. Samples were evaluated using three different preparation methods; no heat application, application of heat by means of a LED curing unit for 60 and 90 seconds (n=10). Heat was applied to cements placed in the mold to apply 'command set' method when setting process occurs. All of the mechanical tests were carried out 24 hours after the setting of glass ionomer cements. The data were evaluated statistically using TwoWay ANOVA. A P-value of < 0.05 was considered significant. Heat application had no significant effect on the diametral tensile strength between control and heated groups of three GICs. Heating the luting glass ionomer cements with a LED curing light during setting, has resulted in both a command set and an improvement in the final compressive strength values for Meron and Kavitan Cem samples. Statistical analysis revealed that heat application showed no effect on the mechanical behavior of Ketac Cem at all heating time. The diametral tensile strength was not enhanced by heat application, but its positive effect on the compressive strength values depend on the materials properties and heating time. The different results can be observed on different materials because the effect of heat on the mechanical properties affected by many factors such as concentration and content of the material, particle size.

Benzer Tezler

  1. Comparative evaluations of traditional house to achieved passive house standard in terms of global warming potential and energy efficiency

    Geleneksel ev ile ulaşılan pasif ev standardının küresel ısınma potansiyeli ve enerji verimliliği açısından karşılaştırılması

    SİMGE VAR

    Yüksek Lisans

    İngilizce

    İngilizce

    2024

    Enerjiİstanbul Teknik Üniversitesi

    Enerji Bilim ve Teknoloji Ana Bilim Dalı

    PROF. DR. HATİCE SÖZER

  2. Assesment of the efficiency of UV light emitting diodes (UV-LEDs) for Fruit Juice Pasteurization

    Meyve Suyu Pastörizasyonu için UV ışık yayan diyotların etkinliğinin (UV-LED) değerlendirilmesi

    MERVE AKGÜN

    Doktora

    İngilizce

    İngilizce

    2019

    Gıda Mühendisliğiİzmir Yüksek Teknoloji Enstitüsü

    Gıda Mühendisliği Ana Bilim Dalı

    PROF. DR. SEVCAN ÜNLÜTÜRK

  3. Akciğer koruyucu ventilasyon ve geleneksel yüksek tidal volum ventilasyonun termoregülasyon üzerine etkilerinin karşılaştırılması

    Comparison of the effects on thermoregulation of lung protection ventilation and traditional high tidal volume ventilation on thermoregulation

    AHMET YÜKSEK

    Tıpta Uzmanlık

    Türkçe

    Türkçe

    2016

    Anestezi ve ReanimasyonAfyon Kocatepe Üniversitesi

    Anesteziyoloji ve Reanimasyon Ana Bilim Dalı

    DOÇ. DR. ELİF DOĞAN BAKI

  4. Analysis of mobile bim adoption at construction site: A case study of a complex infrastructure project

    İnşaat sahasında mobil bım adaptasyonunun analizi: Kompleks altyapı projesi vaka analizi

    ELİF TUĞÇE NURTAN GÜNEŞ

    Yüksek Lisans

    İngilizce

    İngilizce

    2018

    İnşaat Mühendisliğiİstanbul Teknik Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DOÇ. DR. ESİN ERGEN PEHLEVAN

    DR. OZAN KÖSEOĞLU

  5. Transparan AlON seramiklerinin SPS ile üretimi ve geliştirilmesi, farklı katkıların transparanlık ve mekanik özellikler üzerindeki etkilerin incelenmesi

    Production and development of transparent AlON ceramics with SPS, investigation of the effects of different additives on transparency and mechanical properties

    DEMET AYDOĞMUŞ

    Doktora

    Türkçe

    Türkçe

    2024

    Metalurji Mühendisliğiİstanbul Teknik Üniversitesi

    Metalurji ve Malzeme Mühendisliği Ana Bilim Dalı

    PROF. DR. FİLİZ ŞAHİN