Entegre optik aygıtların kararlılık ve güvenilirlik analizi
Stability and reliability analysis of integrated optical devices
- Tez No: 703231
- Danışmanlar: PROF. DR. ELİF ORHAN
- Tez Türü: Doktora
- Konular: Fizik ve Fizik Mühendisliği, Physics and Physics Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2021
- Dil: Türkçe
- Üniversite: Gazi Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İleri Teknolojiler Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Bu çalışmanın amacı; entegre optik aygıtların entegrasyon, paketleme, test ve karakterizasyon süreçlerini analiz ederek seri üretime uygun olup olmadıklarını saptamaktır. Analizler doğrultusunda, 500'den fazla entegre optik aygıtın fiber bütünleme çalışmaları yapılmıştır ve durum D geometrisinde üretilen aygıtlar üretim hattında tercih edilmiştir. Isısal testler referans alınarak aygıtların geçen/kalan sınıflandırması yapılmıştır. Epoksi bölgelerindeki gerilim değişimi termomekanik simülasyonlar gerçekleştirilerek analiz edilmiştir, böylece deneysel bulguların desteklenmesi hedeflenmiştir. Bölge 1 üzerinde indüklenen gerilim birikmesinin önemli bir gerilim mekanizması olduğu teyit edilmiştir. Dalgakılavuzu nüvesi içerisinde indüklenen gerilim seviyesinin optik geçirgenlik üzerindeki etkisi araştırılmıştır. Paketleme çalışmalarında tip 1 uygulaması kullanılarak, tekrar edilebilir ısısal testlerde aygıtlardaki güç salınımının giderildiği gözlemlenmiştir. Paketleme aşamasından sonra açık döngü sistemde elektriksel karakterizasyonlar yapılmıştır. Silikon bazlı koruyucu kaplama yapılan aygıtlarda reset sinyal pikine rastlanmamıştır. -40 °C – (+85) °C sıcaklık aralığında uygulanan ısısal testlerde sıcaklığa bağlı yarı dalga gerilimi değişimi 560 ppm/°C civarında ölçülmüştür ve bu değerin literatür araştırmalarından elde edilen sonuçlar ile tutarlı olduğu saptanmıştır. Kapalı döngü sistemde ısısal yaşlandırma işlemine bağlı olarak performans kararlılık testleri yapılmıştır. 4 farklı aygıt ile yapılan testler sonucunda, tekrarlanan sıcaklık döngüleri sayesinde dünya dönüsünde meydana gelen eğimde yaklaşık 10 kat iyileşme olduğu gözlenmiştir. Interferometre analizlerinde ise kristal içi polarizasyon sönümlenme oranı değişimi, farklı fiber ek noktalarındaki ve fiber taşıyıcı/aygıt arayüzündeki girişim durumları analiz edilmiştir. Yapılan değerlendirmeler sonucunda; entegre optik aygıtın kutuplanma değeri 50 dB olarak ölçülmüştür. Sonuç olarak; bu tezde aygıtların sensör içinde ve sensörden bağımsız olarak analizleri yapılmış olup, ürün bazında isterleri sağlayan aygıtlar seri üretim sürecine dahil edilmiştir. Üretilen entegre optik aygıtlarına çok fonksiyonlu entegre optik aygıt adı verilmiştir. Bu aygıtlar; taktik ve navigasyon seviye fiber optik dönüölçer sensörlerinin temel yapıtaşı olarak kabul edilmektedir.
Özet (Çeviri)
The aim of this study is to determine whether the integrated optical devices are suitable for the mass production by analyzing their integration, packaging, test and characterization processes. In accordance with the analyses, the fiber integration operations of more than 500 devices were carried out and the devices which were produced according to case D geometry were preferred in the production line. By taking as a reference of thermal tests,“successful/fail”classification of the devices were made. The stress variation in the epoxy regions was analyzed by carrying out thermomechanical simulations, so the verification of the experimental findings was aimed. It was confirmed that the stress accumulation induced on region 1 is an important stress mechanism and also it was appointed that this stress accumulation affects the device stability critically. The effect of the induced stress level through the waveguide core on the optical transmission was investigated. In the packaging studies, it was observed that the power fluctuation during repeatable thermal tests could be eliminated by the usage of type 1 application. After the packaging step, the electrical characterizations were carried out in the open-loop system. The reset signal peak was not encountered for the devices coated with the silicone based conformal coating. The temperature dependent half-wave voltage variation was measured around 560 ppm / °C during thermal tests between -40 °C and +85 °C temperature values and it was understood that this value is consistent with the results obtained from the literature researches. In the closed-loop system, performance stability tests based on the thermal aging operation were made. At the end of the test results of four different devices, almost 10 fold recovery in the slope of the earth rate was observed thanks to the repetitive thermal cycles. In the interferometer analyses, the polarization extinction ratio variation inside the device crystal, interference situations at different splice points and between fiber pigtail carrier/device interface were analyzed. In consequence of the evaluations, the polarization of the integrated optical device was measured 50 dB. Finally, in this thesis the analyses of the devices inside and outside the FOG sensor were practiced and so the devices which ensure the requirements in terms of a product were incorporated to the mass production process. The produced integrated optical devices were entitled as multi functional integrated optical chip. These devices are approved as principal milestone of tactic and navigation grade fiber optic gyroscope sensors which are used in military applications.
Benzer Tezler
- Design, fabrication, and optical characterization of thin film devices based on MoS2, MoO3, WO3
MoS2, MoO3, WO3 tabanlı ince film aygıtlarının tasarımı, üretimi ve optik karakterizasyonu
NECİP AYHAN TERTEMİZ
Doktora
İngilizce
2025
Fizik ve Fizik Mühendisliğiİzmir Yüksek Teknoloji EnstitüsüFotonik Ana Bilim Dalı
PROF. DR. SİNAN BALCI
PROF. DR. YAŞAR AKDOĞAN
- Enerji, optik sensör ve aktif gıda paketleme alanlarında kullanılmak üzere yüzeyi işlevselleştirilmiş floresans karbon noktaların geliştirilmesi
Development of surface functionalized fluorescence carbon dots for use in energy, optical sensor, and active food packaging areas
MELİS ÖZGE ALAŞ
Doktora
Türkçe
2022
Kimya MühendisliğiMersin ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
DOÇ. DR. RÜKAN GENÇ ALTÜRK
- Alüminyum konsantrasyonunun aı: nio/psi fotodedektörlerin yapısal,optiksel ve elektriksel özellikleri üzerine etkisinin incelenmesi
Investigation of the effect of aluminum concentration on structural, optical and electrical properties of ai: nio/psi photodetectors
MOHAMMED SULAIMAN MUSTAFA MUSTAFA
Yüksek Lisans
Türkçe
2025
Fizik ve Fizik MühendisliğiEge ÜniversitesiFizik Ana Bilim Dalı
DOÇ. DR. ALPER ÇETİNEL
- LiNbO3 temelli entegre optik nano ölçekli aygıtların simülasyon, dizayn, fabrikasyon ve karakterizasyonu
Simulation, design, fabrication and characterization of LiNbO3 based nanoscale integrated optics devices
EVREN ÖZTEKİN
Yüksek Lisans
Türkçe
2016
Fizik ve Fizik MühendisliğiHacettepe ÜniversitesiNanoteknoloji ve Nanotıp Ana Bilim Dalı
PROF. DR. ERDEM YAZGAN
- Simulation of dynamical refractive index change in on-chip optical devices
Çip ile entegre edilmiş optik aygıtların dinamik refraktif indis ile simülasyonu
ANIL ASLAN
Yüksek Lisans
İngilizce
2019
Fizik ve Fizik MühendisliğiOrta Doğu Teknik ÜniversitesiElektrik-Elektronik Mühendisliği Ana Bilim Dalı
DOÇ. DR. SERDAR KOCAMAN