Evaluating the shear behavior of reinforcedconcrete deep beams without shearreinforcement using strut and tie model
Başlık çevirisi mevcut değil.
- Tez No: 755475
- Danışmanlar: YRD. DOÇ. DR. SHAHRAM DEROGAR
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: RC deep beams, shear failure, shear behaviour, strut-and-tie model, codes of practice
- Yıl: 2020
- Dil: İngilizce
- Üniversite: European University of Lefke
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 79
Özet
Özet yok.
Özet (Çeviri)
Reinforced concrete (RC) deep beams are used mainly as transfer girders, wall footings, and foundation pile caps in building structures. The shear failure is usually the dominant behaviour in RC deep beams due to its relatively small shear span to effective depth ratio. Existing empirical shear design provisions such as ACI 318, AASHTO LRFD and EC 2, overestimate the shear capacity of deep beams and are not suggested to be used for deep beams. Strut and tie model (STM) is depended on the lower bound theorem of plasticity theory and it is implemented to ACI, EC 2 and AASHTO standards for the design of reinforced concrete (R.C.) deep beams. This study aims to evaluate the existing STM shear design provisions in design codes such as ACI 318, EC 2 and AASHTO LRFD with an extensive experimental database on reinforced concrete deep beam with no shear reinforcement. Collected database used in this thesis were tested under point loads and do not contain shear reinforcement. It was shown that the accuracy of shear resistance prediction according to STM model are dependent on various assumptions such as types of struts, nodes and effectiveness factor for concrete strength for inclined strut. However, available codes do not ensure detailed guideline on the use for STM in design. The shear strength predictions by STM adopted in various codes with the extensive experimental database is also evaluated in this study. It was observed that the use of current STM provisions in design codes can lead to an unconservative calculation of nominal capacities for some test specimens.
Benzer Tezler
- Evaluating the shear behavior of reinforced concrete deep beams without shear reinforcement using strut and tie model
Kesme donatısı olmayan betonarme derin kirişlerin kesme davranışının kafes ve kiriş modeli kullanılarak değerlendirilmesi
ROZELİN EKŞİ
Yüksek Lisans
İngilizce
2020
İnşaat MühendisliğiEuropean University of Lefkeİnşaat Mühendisliği Ana Bilim Dalı
YRD. DOÇ. DR. SHAHRAM DEROGAR
- Deprem kuvvetlerine karşı betonarme perdelerin davranışı ve boyutlandırılması
The Behaviour and design of reinforced concrete structural walls for earthquake resistance
YILDIR AKKAYA
Yüksek Lisans
Türkçe
1997
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. ZEKAİ CELEP
- Karayolu köprülerinin sismik boyutlandırılmasıyla ilgili bazı yönetmeliklerin incelenmesi, karşılaştırılması ve uygulamalar
Investigations and comparisons on some rugulations for seismic design of highway bridges and applications
ŞÜKRÜ EROL
- DBYBHY 2007'ye göre tasarlanmış olan bir binanın doğrusal elastik olmayan yöntemlere göre performansının değerlendirilmesi
Performance assessment of a new building designated according to Turkish earthquake code by nonlinear elastic methods
MEŞA DEMİRBAĞ
Yüksek Lisans
Türkçe
2017
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
DOÇ. DR. KONURALP GİRGİN
- Tüp sistemlerin kesin ve yaklaşık yöntemle hesap sonuçlarının karşılaştırılması
Başlık çevirisi yok
BAHADIR AYIK
Yüksek Lisans
Türkçe
1997
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Ana Bilim Dalı
PROF. DR. NAHİT KUMBASAR