Geri Dön

Karton ve ahşap esaslı malzemeler ile üretilen panellerin bazı fiziksel ve mekanik özellikleri

Some physical and mechanical properties of panels produced with cardboard and wood based materials

  1. Tez No: 796237
  2. Yazar: HALİL İBRAHİM ŞEN
  3. Danışmanlar: DOÇ. DR. HASAN ÖZGÜR İMİRZİ
  4. Tez Türü: Yüksek Lisans
  5. Konular: Ağaç İşleri, Wood Products
  6. Anahtar Kelimeler: Belirtilmemiş.
  7. Yıl: 2023
  8. Dil: Türkçe
  9. Üniversite: Gazi Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Ağaç İşleri Endüstri Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 87

Özet

Mobilya endüstrisi ve ağaçişleri sektöründe kullanılan malzemelerin birçoğu ahşap esaslı kompozit malzemelerdir. Bunun en önemli nedeni ahşap esaslı kompozitlerin hafifliği ve kullanım yerinin gerektirdiği performans özelliklerine sahip olmasıdır. Kompozit malzeme, tanımlanabilir bir ara yüze sahip tek bir yapı elde etmek amacıyla, iki ya da daha fazla sayıdaki farklı malzemenin bir araya getirilmesiyle meydana getirilen bir üründür. Bu ürünün/materyalin/malzemenin özellikleri, ara yüzün özelliklerine olduğu kadar, ürünü meydana getiren malzemelerin özelliklerine de bağlıdır. Bu çalışma, oluklu mukavva kartonların geri dönüşümü için alternatif bir malzeme/panel/levha oluşturma amacıyla yapılmıştır. Ahşap esaslı ve oluklu mukavva kartonları ile üretmiş kompozit levhaların/panellerin hafifliği, esnekliği ve kullanım yerinin gerektirdiği direnç özelliklerine sahip olması önemli avantajları sayılabilir. Bu çalışmada, oluklu mukavva/karton ve ahşap esaslı kompozit panellerin rutubet, yoğunluk, eğilme direnci, eğilmede elastikiyet modülü, ısı iletkenlik, ısı geçirgenlik ve ses geçiş̧ kaybı değerleri araştırılmıştır. Panellerin/Levhaların orta katmanında karton (oluklu mukavva), panellerin dış katmanların da ise mobilya ve ağaçişleri endüstrisinde sıklıkla kullanılan MDF, kontrplak ve duralit ahşap esaslı malzemeler kullanılmıştır. Panellerin üretiminde tutkal olarak PVAc tutkalı tercih edilmiştir. Üretilen deney örnekleri rutubet miktarı TS EN 322, yoğunluk TS EN 323, eğilme direnci ve eğilmede elastikiyet modülü TS EN 310, ısı iletkenlik ve ısı geçirgenlik katsayıları TS EN 12667 ve ses geçiş̧ kaybı için TS EN ISO 10534-2 standartları esas alınarak test edilmiştir. Deneyler sonucunda istatistiksel olarak varyans analizi yapılarak LSD testi ile homojenlik gruplarına ayrılmıştır. Sonuç olarak yoğunluk değerleri 0,65-0,70 gr/cm³ arasında, rutubet değerleri % 6 ile % 7 arasında, eğilme direnci ortalama 5 N/mm² ile 18 N/mm² arasında ve eğilmede elastikiyet modülü değeri ortalama 348 N/mm² ile 1878 N/mm² arasında bulunmuştur. Isı iletkenlik katsayısı 0,078 W/m.K (Duralit) ile 0,094 W/m.K (Kontrplak) arasında, ısı geçirgenlik katsayısı değerleri ise ortalama 4,170 W/m².K (MDF) ile 5,530 W/m².K (Kontrplak) arasında bulunmuştur.

Özet (Çeviri)

Most of the materials used in furniture industry and woodworking sectors are produced from wood-based composites. The most important reason for this is the light weight of wood-based composites and the performance properties required by the place of use. By the broadest definition, a composite material is one in which two or more materials that are different are combined to form a single structure with an identifiable interface. The properties of that new structure are dependent upon the properties of the constituent materials as well as the properties of the interface. The aim of this study, is to develop a new method for cardboard recycling. The lightness flexibility and resistance properties on the site of utilization are the major advantages of these wooden composite materials. The lightness flexibility and resistance properties on the site of utilization are the major advantages of these wooden composite materials. In this study, the humidity, density, bending strength and modulus of elasticity, thermal conductivity and heat transmission coefficients values of wooden composite panels based on cardboard were investigated. Cardboard was used in the center layer of the panels manufactured in different manners, whereas, wooden-based materials, which are used frequently in the furniture industry, were used in the external layer. PVAc was preferred as the adhesive in the manufacture of the panels. Bearing in mind the critic loads which may affect its usage, experimental samples were trialed under static loads. Moisture, density, thermal conductivity and heat permeability, bending strength and modulus of elasticity of the prepared panels were investigated. The test specimens produced were tested according to the principles stated in the content TS EN 322 for moisture, TS 2470 for density, and TS EN 310 standards were used. At the end of the tests, by statistically making the analysis of variance, they were separated into homogeneity groups with the Least Significant Difference (LSD) test. The thermal conductivity coefficient was found to be between 0.078 W/m.K (Duralite) and 0.094 W/m.K (Plywood), and the thermal conductivity coefficient values were found to be between 4.170 W/m².K (MDF) and 5.530 W/m².K (Plywood)

Benzer Tezler

  1. The production of bamboo based natural composite materials and comparison of their material properties with particleboard and MDF boards

    Bambu esaslı doğal malzemelerden üretilen kompozit panellerin malzeme davranışlarının yonga levhalar ve MDF plakalar ile karşılaştırılması

    ALİ GÜMÜŞTEKİN

    Yüksek Lisans

    İngilizce

    İngilizce

    2024

    Makine MühendisliğiErciyes Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    PROF. DR. SEDAT ÖZDEN

  2. Resilient design of CLT buildings against fire and earthquake

    Çok katlı CLT binaların yangın ve depreme karşı direnç esaslı tasarımı

    ÖMER ASIM ŞİŞMAN

    Yüksek Lisans

    İngilizce

    İngilizce

    2022

    Deprem Mühendisliğiİstanbul Teknik Üniversitesi

    İnşaat Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ ÖMER TUĞRUL TURAN

    PROF. DR. ARIO CECCOTTI

  3. Biyo-reçine esaslı tekstil kompozitlerinin performans özelliklerinin incelenmesi

    Investigation of performance characteristics of bio-resin based textile composites

    SEMİH ÖZKÜR

    Yüksek Lisans

    Türkçe

    Türkçe

    2021

    Tekstil ve Tekstil Mühendisliğiİstanbul Teknik Üniversitesi

    Tekstil Mühendisliği Ana Bilim Dalı

    DR. ÖĞR. ÜYESİ İPEK YALÇIN ENİŞ

  4. Güçlendirilmiş tabakalı ahşap kompozit panel optimum işlem parametrelerinin belirlenmesi ve üretimi

    Production of reinforced laminated wood composite panel and determination of optimum process parameters

    SEYMEN ÇİFTÇİ

    Doktora

    Türkçe

    Türkçe

    2024

    Ağaç İşleriDüzce Üniversitesi

    Kompozit Malzeme Teknolojileri Ana Bilim Dalı

    DOÇ. DR. HASAN HÜSEYİN CİRİTCİOĞLU

  5. UV ışınları ile sertleşebilen polimerik kaplamaların hazırlanması ve karakterizasyonu

    Preparation and characterization of UV-cured polymeric coatings

    TÜLAY YILMAZ İNAN

    Doktora

    Türkçe

    Türkçe

    1999

    Kimya Mühendisliğiİstanbul Teknik Üniversitesi

    PROF.DR. EKREM EKİNCİ