Kenevir lifi takviyeli epoksi matrisli kompozitlerin üretimi ve karakterizasyonu
Production and characterization of hemp fiber reinforced epoxy matrix composites
- Tez No: 800384
- Danışmanlar: DR. ÖĞR. ÜYESİ ÖZKAN ESKİ
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2023
- Dil: Türkçe
- Üniversite: Kastamonu Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 124
Özet
Bu çalışmada sürdürülebilir doğal lif çeşidi olan kenevir liflerinin, kompozit malzeme üretimlerinde alternatif takviye elemanı olarak kullanılabilme ve farklı açı dizilimlerinin malzeme mukavemet değerlerini değiştirme durumu incelenmiştir. Dokunmamış halde temin edilen kenevir lifleri eşit ebatlarda boyutlandırılarak 20x20 cm'lik hazırlanan kalıp içerisine 90°,60° ve 45° açılarla dizilip, epoksi matris malzemesi ile beslenmesi sağlanmıştır. Toplamda 4 kat olup ve her katı bir önceki katın tersi açı ile serilen numuneler, epoksi matrisle birleştirilip basınç altında sıkıştırılmışlardır. Sıkıştırılma işlemleri biten numuneler bir gün boyunca açık havada sertleşmeye bırakılmışlardır. Kompozit malzeme üretimlerinde yaygın kullanıma sahip olan karbon elyaf lifleri de bu çalışmada kullanılarak kenevir liflerin karbon elyaf ile takviyelendirilmesi sonucu numunelerin sergiledikleri performanslar çalışma içerisinde analiz edilmiştir. Açılar ve serim yöntemleri aynı kalmak koşuluyla karbon elyafın takviye edilmesiyle üretilen sandviç kompozit numuneler, basınç altında preslenmiş ve açık havada sertleşmeye bırakılmışlardır. Bu numunelerin yanında atık kenevir liflerinin değerlendirilmesi bazında 1 cm ve 2 cm şeklinde boyutlandırılan lifler de sadece kenevir lifi ve karbon elyaf kullanılarak aynı yöntemle üretilmişlerdir. Üretilen numunelere üç nokta eğme ve darbe testi yapılmıştır. ASTM D790 standartlarında numuneler elde edilerek eğilme mukavemetleri tespit edilmiş ve mikroskobik görüntüleri elde edilmiştir. Sonuçlar incelendiğinde 90° kenevir lifi+ karbon elyaf numunesinin diğer numunelerden daha yüksek eğilme mukavemeti değeri sergilediği görülmüştür. Sadece karbon elyaf numunesinin eğilme mukavemet değeri, kenevir takviyeli numuneden düşük çıkmıştır. Atık kenevir liflerinin değerlendirilmesi açısından üretilen numunelerin mukavemet değerlerine bakıldığı zaman kenevir liflerinin boyunun kısalması ve karbon elyaf ile takviyelendirilmesi eğilme mukavemet değerlerinde artışa sebep olmuştur. ASTM D256 standartlarına uygun numuneler üretilerek darbe testleri gerçekleştirilmiştir. Darbe testi sonuçlarına göre 45° açılı numunelerde kırılmaların kayma düzlemi üzerinde gerçekleştiği gözlemlenirken, darbe tokluk değerini en yüksek 90° kenevir lifi+ karbon elyaf numunesinin verdiği görülmüştür.
Özet (Çeviri)
In this study, the ability of hemp fibers, which are sustainable natural fibers, to be used as alternative reinforcement elements in composite material production and the change in material strength values of different angle arrangements were investigated. Hemp fibers provided in non-woven form were sized in equal sizes and arranged in a 20x20 cm mold with 90°, 60° and 45° angles and fed with epoxy matrix material. The specimens, which have 4 layers in total and each layer is laid at an angle opposite to the previous layer, are combined with the epoxy matrix and compressed under pressure. After compression, the specimens were left to harden in the open air for one day. Carbon fiber fibers, which are widely used in the production of composite materials, were also used in this study and the performances of the samples were analyzed in the study as a result of the reinforcement of hemp fibers with carbon fibers. The sandwich composite specimens produced by reinforcing carbon fiber with the same angles and lay-up methods were pressed under pressure and left to harden in the open air. In addition to these specimens, fibers sized as 1 cm and 2 cm based on the utilization of waste hemp fibers were produced by the same method using only hemp fiber and carbon fiber. Three-point bending and impact tests were performed on the produced specimens. Specimens were obtained in accordance with ASTM D790 standards, bending strengths were determined and microscopic images were obtained. When the results were examined, it was seen that the 90° hemp fiber + carbon fiber sample exhibited a higher bending strength value than the other samples. Only the flexural strength value of the carbon fiber sample was lower than the hemp reinforced sample. When the strength values of the samples produced in terms of the utilization of waste hemp fibers are examined, the shortening of the length of hemp fibers and reinforcement with carbon fiber caused an increase in flexural strength values. Impact tests were performed by producing specimens in accordance with ASTM D256 standards. According to the impact test results, it was observed that the fractures in the 45° angle specimens occurred on the shear plane, while the 90° hemp fiber + carbon fiber specimen gave the highest impact toughness value.
Benzer Tezler
- Investigation of the mechanical properties of hemp fiber reinforced epoxy base nanocomposites
Kenevir elyaf takviyeli epoksi bazli nanokompozitlerin mekanik özelliklerinin incelenmesi
ERTAN KESEN
Yüksek Lisans
İngilizce
2023
Makine MühendisliğiGaziantep ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. AHMET ERKLİĞ
- Epoksi esaslı kenevir lif ile güçlendirilmiş kompozitlerin özelliklerinin incelenmesi
Examination of properties of composites strenghtened with epoxy-based hemp fibers
GÖKHAN UĞURER
Yüksek Lisans
Türkçe
2022
Kimya MühendisliğiEskişehir Osmangazi ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
DOÇ. DR. ALİME ÇITAK
- Doğal elyaf takviyeli koruyucu tekstil yapısı geliştirilmesi
Development of natural fiber reinforced protective textile structure
SİNAN KOCAÖZ
Yüksek Lisans
Türkçe
2023
Tekstil ve Tekstil MühendisliğiMarmara ÜniversitesiTekstil Mühendisliği Ana Bilim Dalı
DOÇ. DR. MUHAMMET UZUN
- Yeni nesil yapısal ahşap sandviç panellerin mekanik, termal ve akustik özellikleri
Mechanic, thermal and acoustic properties of novel structural wood sandwich panels
MURAT GÜNDÜZ
Doktora
Türkçe
2022
Mühendislik Bilimleriİstanbul Üniversitesi-CerrahpaşaOrman Endüstri Mühendisliği Ana Bilim Dalı
PROF. DR. TÜRKER DÜNDAR
- Biyobazlı materyaller kullanılarak şekil hafızalı polimer kompozit malzeme üretimi
Shape memory polymer composite material production with using biobased materials
MERVE UYAN
Doktora
Türkçe
2024
Metalurji MühendisliğiEge ÜniversitesiGüneş Enerjisi Ana Bilim Dalı
DOÇ. DR. MELİH SONER ÇELİKTAŞ