Fitilli ısı borularında farklı iş akışkanları kullanımının eğim açısına göre deneysel incelenmesi
Experimental investigation of the use of different working fluids in wicked heat pipes according to inclination angle
- Tez No: 837608
- Danışmanlar: DOÇ. DR. AHMET ALİ SERTKAYA
- Tez Türü: Yüksek Lisans
- Konular: Enerji, Makine Mühendisliği, Energy, Mechanical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2023
- Dil: Türkçe
- Üniversite: Selçuk Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Makine Mühendisliği Bilim Dalı
- Sayfa Sayısı: 45
Özet
Teknolojinin gelişimiyle birlikte enerji gereksinimi artmakta ve bu da enerji kaynaklarına olan ihtiyacı artırmaktadır. Ancak, mevcut enerji kaynaklarının kısıtlı olması ve çevresel sorunlar nedeniyle kısıtlar ortaya çıkmaktadır. Bu durum, enerji kaynaklarının kullanımının yanı sıra yeni ve daha sürdürülebilir enerji kaynaklarının arayışını da beraberinde getirmektedir. Isı taşıyan sistemler, enerji transferinde önemli bir rol oynar. Isı enerjisinin bir ortamdan başka bir ortama taşınmasında kullanılan sistemlerden birisi de ısı borularıdır. Bu çalışmada fitilli ısı borularının farklı iş akışkanları ile farklı çalışma şartlarında çalışma performanslarının belirlenmesi deneysel olarak incelenmiştir. Çalışmada, 15 mm çapında 450 mm uzunluğunda bakır boru, içerisine fitil olarak 150 mesh gözenekli nikel-krom alaşımından imal edilmiş tek katlı elek teli konularak farklı iş akışkanları şarj edilmiştir. Farklı parametrelere göre deney düzeneği ayarlanarak ısı borusunun performansları deneysel olarak incelenmiş ve en uygun çalışma şartları belirlenmiştir. Çalışma kapsamında, beş farklı iş akışkanının aynı geometride ısı borularına hacimsel olarak eşit miktarda şarj edilmiş ve ısı borularının farklı ısıl giriş güçleri ve yatay konumla beraber dört farklı eğim açısında termal performansı değerlendirilmiştir. Deneylerde 10 W, 20 W, 30 W, 40 W ve 50 W evaporatör bölgesinde ısıl giriş güçleri kullanılmıştır. Yatay eksen 0° olmak üzere 0°, 30°, 60° ve 90° eğim açılarında deneyler yapılmıştır. Isı borusunun performansı eğim açısına, giriş gücüne göre değerlendirilmiştir. Elde edilen sonuçlara göre R134a iş akışkanında evaporatör ve kondenser arası yüzey sıcaklık farklarının düşük olduğu gözlemlenmiştir. Isı borusunun toplam ısıl direncinde farklı ısı güçleri için en düşük ısıl direnç R134a akışkanında ve en yüksek ısıl direnç saf su için elde edilmiştir. Isıl dirençlerin sayısal değeri R134a hariç birbirine yakın olduğu tespit edilmiştir.
Özet (Çeviri)
With the development of technology, the need for energy increases and this increases the need for energy resources. However, constraints arise due to limited available energy resources and environmental problems. This situation brings along the search for new and more sustainable energy sources as well as the use of energy resources. Heat transfer systems play an important role in energy transfer. One of the systems used to transfer heat energy from one medium to another is heat pipes. In this study, the performance of wick heat pipes under different working conditions with different working fluids was experimentally investigated. In the study, a copper tube with a diameter of 15 mm and a length of 450 mm was placed in a single layer sieve wire made of nickel-chromium alloy with 150 mesh as a wick and charged with different working fluids. By adjusting the experimental setup according to different parameters, the performances of the heat pipe were experimentally investigated and the optimum operating conditions were determined. Within the scope of the study, five different working fluids were charged to the heat pipes of the same geometry in equal volumetric amounts and the thermal performance of the heat pipes was evaluated at different thermal input powers and four different inclination angles with horizontal position. Thermal input powers of 10 W, 20 W, 30 W, 40 W and 50 W were used in the evaporator region. Experiments were conducted at inclination angles of 0°, 30°, 60° and 90° with the horizontal axis at 0°. The performance of the heat pipe was evaluated according to the inclination angle and input power. According to the results obtained, it is observed that the surface temperature differences between evaporator and condenser are low in R134a working fluid. In the total thermal resistance of the heat pipe, the lowest thermal resistance was obtained for R134a fluid and the highest thermal resistance was obtained for pure water for different heat powers. The numerical values of the thermal resistances were found to be close to each other except R134a.
Benzer Tezler
- Yerçekimi destekli ısı borularında fitil kullanımının ısı borusunun çalışma performansına etkisi
The effect of wick usage on the operating performance of gravity assisted heat pipe
HASAN YILDIRIM
Yüksek Lisans
Türkçe
2009
EnerjiSüleyman Demirel ÜniversitesiMakine Eğitimi Ana Bilim Dalı
YRD. DOÇ. DR. AHMET ÖZSOY
- Isı borulu güneş enerjisi ile çalışan hacim ısıtma amaçlı bir konvektörün geliştirilmesi
Başlık çevirisi yok
A.MURAT GÜLÇAĞ
- Isı borularının modellenmesi ve optimizasyonu
Modeling and optimization of heat pipes
MEHMED AKİF PAKSOY
Doktora
Türkçe
2020
Makine MühendisliğiGebze Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DR. ÖĞR. ÜYESİ SALİH ÖZEN ÜNVERDİ
- Assessment of sintered wick heat pipe performance by modeling phase change in surface pores
Yüzey gözeneklerindeki faz değişiminin modellenmesi ile sinterlenmiş fitilli ısı borusu performansının değerlendirilmesi
ŞÜKRÜ KAAN YENER
Yüksek Lisans
İngilizce
2024
Makine MühendisliğiOrta Doğu Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. ZAFER DURSUNKAYA
DOÇ. DR. BARBAROS ÇETİN