Farklı polimerizasyon yöntemleriyle polimerize edilen akışkan kompozitlerin dönüşüm derecesi ve renklenmesinin İn-Vitro olarak incelenmesi
In-Vitro investigation of the degree of conversion and discoloration of flowable composites polymerized by different polymerization methods
- Tez No: 943173
- Danışmanlar: DR. ÖĞR. ÜYESİ SULTAN AKTUĞ KARADEMİR
- Tez Türü: Diş Hekimliği Uzmanlık
- Konular: Diş Hekimliği, Dentistry
- Anahtar Kelimeler: Akışkan kompozit, bulk-fill kompozit, dönüşüm derecesi, kürleme modu, renk stabilitesi, Flowable composite, bulk-fill composite, degree of conversion, curing mode, color stability
- Yıl: 2025
- Dil: Türkçe
- Üniversite: Ordu Üniversitesi
- Enstitü: Diş Hekimliği Fakültesi
- Ana Bilim Dalı: Restoratif Diş Tedavisi Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
Amaç: Bu çalışmanın amacı farklı kürleme modlarının farklı akışkan kompozitlerin dönüşüm derecesi ve renk stabilitesi üzerindeki etkisini değerlendirmektir. Gereç ve Yöntem: Bu çalışmada 4 farklı akışkan kompozit [Estelite Bulk Fill Flow (EBF), G-aenial Universal Injectable (GUI), Tetric N-Flow Bulk Fill (TNF), Filtek Bulk Fill Flowable (FBF)] kullanıldı. Kompozit materyaller, LED ışık cihazının (VALO Cordless, Ultradent, ABD) 3 farklı kürleme modunda (standart mod: 1000 mW/cm2, 1*20 s; yüksek güç modu: 1400 mW/cm2, 3*4 s; ekstra güç modu: 3200 mW/cm2, 2*3 s) polimerize edilerek 5 mm çapında 4 mm yüksekliğinde her grupta 10 örnek olmak üzere 120 silindirik numune hazırlandı (n=10). Örneklerin dönüşüm derecesi FTIR spektroskopisi ile kaydedildi. Numunelerin renk değerleri başlangıçta ve kahve solüsyonunda bekletildikten sonraki 7. ve 14. günde spektrofotometre kullanılarak kaydedildi. Renk değişim değerleri CIEDE2000 formülüne göre hesaplandı. Veriler SPSS kullanılarak, iki yönlü varyans analizi, tek yönlü varyans analizi, post hoc Tukey ve Tamhane's T2 ile istatistiksel olarak analiz edildi (α=0.05). Bulgular: Kompozit materyal tipi, polimerizasyon modu, materyal ve polimerizasyon modu etkileşiminin dönüşüm derecesi ve renk değişikliği üzerindeki etkisi istatistiksel olarak anlamlı bulundu (p<0.001). Tüm kompozitlerde en yüksek dönüşüm derecesi yüksek güç modunda kürleme ile bulundu. Materyallerin ekstra güç modundaki dönüşüm derecesi, yüksek güç moduna kıyasla daha düşüktü ve bu azalma FBF ve GUI için istatistiksel olarak anlamlı idi (p<0.05). En az renk değişimi yüksek güç modunda kürleme ile elde edildi. Ekstra güç modunda renk değişimi 7. günde EBF ve FBF'de; 14.günde TNF, FBF ve EBF'de yüksek güç moduna kıyasla anlamlı derecede yüksekti (p<0.05). Sonuçlar: LED ışık cihazlarının geliştirilmesiyle birlikte, zaman kazandıran ekstra güç kürleme modu, akışkan kompozitlerde dönüşüm derecesinde azalmaya ve renklenmede artışa neden olabilir.
Özet (Çeviri)
Aim: The aim of this study is to evaluate the effect of different curing modes on the degree of conversion and color stability of different flowable composites. Material and method: In this study, four different flowable composites [Estelite Bulk Fill Flow (EBF), G-aenial Universal Injectable (GUI), Tetric N-Flow Bulk Fill (TNF), Filtek Bulk Fill Flowable (FBF)] were used. The composite materials were polymerized using three different curing modes (standard mode: 1000 mW/cm², 1*20 s; high power mode: 1400 mW/cm², 3*4 s; extra power mode: 3200 mW/cm², 2*3 s) of an LED light device (VALO Cordless, Ultradent, USA). A total of 120 cylindrical samples with a 5 mm diameter and 4 mm height were prepared, with 10 samples per group (n=10). The degree of conversion of the samples was recorded using FTIR spectroscopy. The color values of the samples were recorded initially and on the 7th and 14th days after being immersed in a coffee solution, using a spectrophotometer. Color change values were calculated according to the CIEDE2000 formula. The data were statistically analyzed using SPSS, with two-way ANOVA, one-way ANOVA, post hoc Tukey, and Tamhane's T2 tests (α=0.05). Results: The effect of composite material type, polymerization mode, and the interaction between material and polymerization mode on the degree of conversion and color change was found to be statistically significant (p<0.001). The highest degree of conversion was observed in all composites when cured using the high power mode. The degree of conversion in the extra power mode was lower compared to the high power mode, and this decrease was statistically significant for FBF and GUI (p<0.05). The least color change was observed when curing with the high power mode. Color change in the extra power mode on day 7 was significantly higher in EBF and FBF compared to the high power mode, while on day 14, it was significantly higher in TNF, FBF, and EBF compared to the high power mode. (p<0.05). Conclusions: With the development of LED light devices, the time-saving extra power curing mode may lead to a decrease in the degree of conversion and an increase in discoloration in flowable composites.
Benzer Tezler
- Catalyzing the inverse vulcanization reaction via 1,3-benzoxazines
Ters vulkanizasyon tepkimesinin 1,3-benzoksazinlerle katalizlenmesi
AHMAD SHAFIZADA
Yüksek Lisans
İngilizce
2023
Kimyaİstanbul Teknik ÜniversitesiKimya Ana Bilim Dalı
PROF. DR. BARIŞ KIŞKAN
- Süperkritik akışkan ortamında kopolimerizasyon
Copolymerization in supercritical fluid
MEHMET YILMAZ
Yüksek Lisans
Türkçe
2009
Kimya MühendisliğiAnkara ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
PROF. DR. AYLA ÇALIMLI
PROF. DR. ERHAN BİŞKİN
- Production of antibacterial biobased blends for biomedical use
Biyomedikal alanlarda kullanılmak üzere antibakteriyel özellikli biyobazlı harmanların eldesi
METE DERVİŞCEMALOĞLU
Yüksek Lisans
İngilizce
2023
Biyoteknolojiİstanbul Teknik ÜniversitesiMoleküler Biyoloji-Genetik ve Biyoteknoloji Ana Bilim Dalı (disiplinlerarası)
PROF. DR. FATOŞ YÜKSEL GÜVENİLİR
- Konvansiyonel ve 3 boyutlu yazıcı sistemleriyle üretilen maksiller tam protez kaidelerininin yüzey adaptasyonlarının ve mekanik dayanımlarının değerlendirilmesi
Evaluation of the surface adaptation and mechanical strength of maxillary complete denture bases fabricated by conventional and three-dimensional printing systems
AFRA BANU ERGİN
Diş Hekimliği Uzmanlık
Türkçe
2026
Diş HekimliğiRecep Tayyip Erdoğan ÜniversitesiProtetik Diş Tedavisi Ana Bilim Dalı
DOÇ. DR. MURAT ALKURT
- Immobilization of lipase enzyme onto precipitated silica and synthesis of polycaprolactone
Lipaz enziminin çöktürülmüş silika üzerine immobilizasyonu ve polikaprolakton sentezi
NUREFŞAN GÖKALP
Yüksek Lisans
İngilizce
2015
Biyoteknolojiİstanbul Teknik ÜniversitesiKimya Mühendisliği Ana Bilim Dalı
PROF. DR. FATOŞ YÜKSEL GÜVENİLİR