Geri Dön

Gaz atomizasyonu ile metal tozu üretiminde, nozul geometrisinin toz boyutuna etkisinin araştırılması

Investigation of nozzle geometry on the particle size for powder production by gas atomisation

  1. Tez No: 202793
  2. Yazar: EMİN SONER YILDIZ
  3. Danışmanlar: YRD. DOÇ. DR. RAHMİ ÜNAL
  4. Tez Türü: Yüksek Lisans
  5. Konular: Makine Mühendisliği, Mechanical Engineering
  6. Anahtar Kelimeler: Gaz atomizasyon, metal tozu, nozul geometrisi, Gas Atomisation, metal powder, nozzle geometry
  7. Yıl: 2007
  8. Dil: Türkçe
  9. Üniversite: Dumlupınar Üniversitesi
  10. Enstitü: Fen Bilimleri Enstitüsü
  11. Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
  12. Bilim Dalı: Belirtilmemiş.
  13. Sayfa Sayısı: 88

Özet

Bu çalısmada, gaz atomizasyonu ile metal tozu üretiminde nozul geometrisinin toz tane boyutu ve özelliklerine etkisi arastırılmıstır. Toz üretim deneyleri Dumlupınar Gaz Atomizasyon Ünitesi'nde gerçeklestirilmistir. Birbirine çok yakın atomizasyon gaz basıncında, farklı nozullar kullanılarak yapılan deneylerde, nozul geometrisi ve metal akıs borusu çıkıntı mesafesi değisiminin toz tane büyüklüğü ve dağılımı ile morfolojilerine olan etkileri arastırılmıstır. Toz tane boyutu ve dağılımı, lazer ısın yöntemi ile, toz sekil ve morfolojileri taramalı elektron mikroskobu (SEM) ile incelenmistir. Atomizasyon gazı olarak azot, malzeme olarak kalay kullanılarak yapılan deneylerde Gaz/Metal kütlesel debi oranının artmasıyla toz boyutunun küçüldüğü tespit edilmistir. Aynı gaz çıkıs alanında metal akıs borusu çıkıntı mesafesinin artmasıyla toz tane boyutunun küçüldüğü gözlemlenmistir. En küçük tozlar 10 mm metal akıs borusu çıkıntı mesafesinde 12,05 ?m boyutunda elde edilmistir. Aynı metal akıs borusu çıkıntı mesafesinde nozul uç geometrisindeki değisikliğin toz boyutunu önemli ölçüde etkilemediği görülmüstür. 5 mm çıkıntı mesafesinde iki farklı nozul geometrisi ile elde edilen kalay tozlarının ortalama tane büyüklükleri 14,11 ?m ve 14,26 ?m olarak ölçülmüstür. Üretimi gerçeklestirilen tozların çoğunluğunun küresel sekilde ve pürüzsüz bir yüzeye sahip olduğu tespit edilmistir. ?nce tozların daha iri tozlar üzerinde az miktarda uydulasma olusturdukları ve iri tozlarda hücresel yapılar gözlemlenmistir.

Özet (Çeviri)

In this study, the effect of the nozzle geometry for powder production by gas atomisation was investigated. Powder production was carried out at the Dumlupınar Gas Atomisation unit. Different nozzle tip geometry and protrusion lengths were used for the investigation of particle size and powder morphology. Powder particle size was measured by using laser particle sizer, powder morphology was determined by using SEM. Nitrogen was used as the atomisation gas for the tin powder production. As the Gas/Metal mass flow ratio was increased the powder particle size was reduced. The higher protrusion length of the nozzle decreased the powder size. The smallest powder size of 12.05 microns was obtained with 10 mm protrusion length. The tip geometry at the same protruion length has no significant effect for the powder size. For the 5 mm protrusion length the two different tip geometry produced the powder size of 14,11 and 14,26 microns. Produced powders are mostly spherical and have smooth surfaces. A few satellite formation and cellular surface structure at the big powder surfaces were observed.

Benzer Tezler

  1. Gaz atomizasyon yöntemi ile metal tozu üretiminde gaz akış modeli

    Models of atomization gas flow in manufacturing of metal powder by gas atomization

    ÇAĞATAY MEHMET BOZKURT

    Yüksek Lisans

    Türkçe

    Türkçe

    2004

    Makine MühendisliğiDumlupınar Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    Y.DOÇ.DR. RAHMİ ÜNAL

  2. Hesaplamalı akışkanlar dinamiği ile gaz atomizasyonu nozulunun modellenmesi ve toz üretiminin deneysel araştırılması

    Modeling of gas atomization nozzle by computational fluid dynamics and investigation of powder production by experimentally

    MUSTAFA GÜLEŞEN

    Doktora

    Türkçe

    Türkçe

    2013

    Makine MühendisliğiEskişehir Osmangazi Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    YRD. DOÇ. DR. MELİH CEMAL KUŞHAN

    PROF. DR. RAHMİ ÜNAL

  3. Gaz atomizasyon yöntemi ile metal tozu üretiminde süpersonik nozul değişkenlerinin toz özelliklerine etkisinin araştırılması

    Investigation of the effect of supersonic nozzle parameters to the properties of the powders produced by gas atomization

    ALPEREN AKSOY

    Yüksek Lisans

    Türkçe

    Türkçe

    2005

    Makine MühendisliğiDumlupınar Üniversitesi

    Makine Mühendisliği Ana Bilim Dalı

    Y.DOÇ.DR. RAHMİ ÜNAL

  4. Gaz atomizasyon yöntemiyle AM60 tozu üretimi ve karakterizasyonu

    AM60 powder production and characterization by gas atomization method

    TAYFUN ÇETİN

    Doktora

    Türkçe

    Türkçe

    2018

    Metalurji MühendisliğiKarabük Üniversitesi

    İmalat Mühendisliği Ana Bilim Dalı

    PROF. DR. MUSTAFA BOZ

  5. The production of AZ31 alloys by gas atomisation method and its characteristics

    Gaz atomizasyon yöntemiyle az31 tozu üretimi ve karakterizasyonu

    KAMAL AKRA

    Doktora

    İngilizce

    İngilizce

    2019

    Metalurji MühendisliğiKarabük Üniversitesi

    İmalat Mühendisliği Ana Bilim Dalı

    PROF. DR. MUSTAFA BOZ