Farklı tahribatsız muayene metodlarıyla malzeme hatalarının tesbiti
Defect determination by using different nondestructivetesting methods
- Tez No: 35654
- Danışmanlar: DOÇ. DR. BERİL TUĞRUL
- Tez Türü: Yüksek Lisans
- Konular: Fizik ve Fizik Mühendisliği, Physics and Physics Engineering
- Anahtar Kelimeler: Kalite kontrol, Malzeme hataları, Tahribatsız muayene yöntemleri, Quality control, Material fault, Nondestructive inspection methods
- Yıl: 1994
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Nükleer Uygulamalar Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: Belirtilmemiş.
Özet
But at the same time we had to use surface methods. Because, these two volumetric methods weren't enought to determine the fine discontinuities on the surface of the parts, especially for thick parts. Xllla) X-ray radiography b) Gamma-ray radiography. In the ultrasonic testing the reference part should be inspected for four surfaces. For detailed inspection different probs were used in this inspection. However, all discontinuities in this reference part couldn't be determined easily. In the magnetic particles inspections, two different apparatus were used. These are coil type apparatus and yoke type apparatus. By using both of them, detailed knowledge about the discontinuities which were open to the surface could be taken. In liquid penetrant testing, about all discontinuities were detected apain on the surface. Moreover, this method is cheaper than magnetic particle method. If the fluoresant magnetic particles or fluoresant penetrant are preferred for the sensitive results, then the“black lamp”should be used for the evaluation. In here, emission rate and wavelenght of the ultraviolet rays from the black lamp is important for the sensitivity of the method. At the end of the inspections which contained five different techniques, since both the radiography and ultrasonic are volumetric methods, they gave“good”results for the whole of a part. Xll
Özet (Çeviri)
But at the same time we had to use surface methods. Because, these two volumetric methods weren't enought to determine the fine discontinuities on the surface of the parts, especially for thick parts. Xllla) X-ray radiography b) Gamma-ray radiography. In the ultrasonic testing the reference part should be inspected for four surfaces. For detailed inspection different probs were used in this inspection. However, all discontinuities in this reference part couldn't be determined easily. In the magnetic particles inspections, two different apparatus were used. These are coil type apparatus and yoke type apparatus. By using both of them, detailed knowledge about the discontinuities which were open to the surface could be taken. In liquid penetrant testing, about all discontinuities were detected apain on the surface. Moreover, this method is cheaper than magnetic particle method. If the fluoresant magnetic particles or fluoresant penetrant are preferred for the sensitive results, then the“black lamp”should be used for the evaluation. In here, emission rate and wavelenght of the ultraviolet rays from the black lamp is important for the sensitivity of the method. At the end of the inspections which contained five different techniques, since both the radiography and ultrasonic are volumetric methods, they gave“good”results for the whole of a part. XllBut at the same time we had to use surface methods. Because, these two volumetric methods weren't enought to determine the fine discontinuities on the surface of the parts, especially for thick parts. Xllla) X-ray radiography b) Gamma-ray radiography. In the ultrasonic testing the reference part should be inspected for four surfaces. For detailed inspection different probs were used in this inspection. However, all discontinuities in this reference part couldn't be determined easily. In the magnetic particles inspections, two different apparatus were used. These are coil type apparatus and yoke type apparatus. By using both of them, detailed knowledge about the discontinuities which were open to the surface could be taken. In liquid penetrant testing, about all discontinuities were detected apain on the surface. Moreover, this method is cheaper than magnetic particle method. If the fluoresant magnetic particles or fluoresant penetrant are preferred for the sensitive results, then the“black lamp”should be used for the evaluation. In here, emission rate and wavelenght of the ultraviolet rays from the black lamp is important for the sensitivity of the method. At the end of the inspections which contained five different techniques, since both the radiography and ultrasonic are volumetric methods, they gave“good”results for the whole of a part. XllBut at the same time we had to use surface methods. Because, these two volumetric methods weren't enought to determine the fine discontinuities on the surface of the parts, especially for thick parts. Xlll
Benzer Tezler
- Detection and classification of flaws from ultrasonic tomography images of composite materials based on deep learning
Derin öğrenme tabanlı kompozit malzemelerin ultrasonik tomografi görüntülerinden kusurların tespiti ve sınıflandırılması
ABDULKADİR GÜLŞEN
Doktora
İngilizce
2024
Bilgisayar Mühendisliği Bilimleri-Bilgisayar ve KontrolAbdullah Gül ÜniversitesiElektrik ve Bilgisayar Mühendisliği Ana Bilim Dalı
DOÇ. DR. BURCU GÜNGÖR
DR. BURAK KOLUKISA
- Investigation of non-contact smartphone-based monitoring of structures
Yapıların akıllı telefon tabanlı temassız sağlık izleme metodları ile incelenmesi
MEHMET SEFA ORAK
Doktora
İngilizce
2021
İnşaat Mühendisliğiİstanbul Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. TURGUT ÖZTÜRK
- Farklı malzemelerin radyografik yöntemle yarı-değer kalınlığının tespiti
Başlık çevirisi yok
KEMAL ÜÇER
Yüksek Lisans
Türkçe
1997
Nükleer Mühendislikİstanbul Teknik ÜniversitesiMetalurji Mühendisliği Ana Bilim Dalı
PROF. DR. ALİ NEZİHİ BİLGE
- Determination of relationship between weld quality and mechanical strength in different steels
Farklı çeliklerde kaynak kalitesi ile mekanik mukavemet arasındaki ilişkinin tesbiti
OSMAN ALPER SOYLU
Yüksek Lisans
İngilizce
2004
Makine MühendisliğiOrta Doğu Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. BÜLENT DOYUM