B2 O3 katkısının doğrudan sinterlenen isatropik sert ferritlerin manyetik özellikleri üzerine etkisi
Effect of B2 O3 addition on the magnetic propertiesof direct sintered isotropic hard ferrites
- Tez No: 39382
- Danışmanlar: DOÇ.DR. OSMAN T. ÖZKAN
- Tez Türü: Yüksek Lisans
- Konular: Meteoroloji, Meteorology
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 1993
- Dil: Türkçe
- Üniversite: İstanbul Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 101
Özet
Ferrit olarak bilinen ferrimanyetik oksitler, manyetik özelliklere sahip seramik malzemelere verilen bir isimdir. Genel olarak kimyasal bileşimi MeO. nFe2Oj olarak ifade edilen ferritler n=6 ve Me Mn, Sr, Pb2+ iyonlarını temsil ettiği zaman bu malzeme hegzagonal ferrit veya sert ferrit olarak tanımlanır. Sert ferritlerde eğer manyetik özellikler her doğrultuda aynı ise bunlar isotropik, belli bir doğrultuda geliştirilmişse anisotropik olarak isimlendirilir. Ferritlerde manyetik özellikler genellikle stokoimetrik oran olan n=6'dan biraz daha düşük oranlarda elde edilmektedir. Bu nedenle araştırmada BaO. 5.6Fe2Üj formülü esas alınmıştır. Yapılan bu çalışmada isotropik sert ferritlere B2O3 katkısının manyetik özelliklere etkisinin incelenmesi amaçlanmıştır. Bileşime BjCh katkısı molce 0, 0.01, 0.05, 0.1, 0.15 ve 0.2 olarak ilave edilmiştir. îkinci olarakta ferrit bileşiminin ağırlıkça yaklaşık %85'ini oluşturan hematitin de yerli kaynaktan kullanılması hedeflenmiştir. Sonuç olarak, isotropik sert ferritlere BjOj katkısının hem hematitin hegzagonal f err ite dönüşümünü kolaylaştırdığı, hem de klasik seramik yönteminin kademelerinden kalsinasyon aşamasının kaldırılmasına olanak tanıdığı saptanmıştır. 0.2 mol BjOj katkılı numunenin 1000°C'de x-ışını difraksiyon analizinde serbest hematitin tamamen yok olduğu bulunmuştur. Kalsinasyon aşamasından geçerek ve 1250°C'de sinterlenerek üretilen ferritlerde kalıcı manyetisasyon (Br) 0.2 Tesla (2125 Gauss), zorlayan kuvvet (Hc) 21*10^ Amper/m (2600 Oersted) manyetik enerji [(BH)ma£] 7200 Joule/m3 (0.9x10° Gauss-oersted) iken 12503C de doğrudan sinterlenen ferritlerde Br 0.2 Tesla (2000 Gauss), Hc 22*10* Amper/m (2800 Oersted), (BH)fflaî 7200 Joule/m3 (0.9>rlQ6 Gauss-Oersted) bulunmuş, 0.05 mol B2O3 katkısıyla 1250°C'de doğrudan sinterlenen ferritlerde ise Br 0.23 Tesla (2300 Gauss), Hc 19*104 Amper/m (2400 Oersted), (BH)aas 9600 Joule/m3 (1.2*10° Gauss-Oersted) olarak saptanmıştır. iv
Özet (Çeviri)
Ferrite is a general name given to a group of ceramic materials which show f errimagnetic properties. Ferrites can have a wide range of magnetic properties depending on their crystalline structure and chemical composition. The general chemical composition of ferrites can be expressed as Me0.nFe2Ö3' $hen n=l and Me represents the divalent ions such as Ni, Mn, Zn, they are referred as“Soft Ferrites”. In this case the magnetic properties of the material can easily be changed with externally applied small magnetic fields. Although the magnetic properties are more inferior than the metallic materials, soft ferrites have been found to have a wide range of application in modern electronics, especially at high frequencies. In the general composition, when n=6 and Me represents divalent ions such as Ba, Sr, Pb permanent magnetic properties are developed. Such ferrites are named“Hexagonal”or“Hard Ferrites”. These, too, have inferior magnetic properties compared to the metal ones. However due to their very low cost of production, hard ferrites have been found to have a wide application such as; magnetic clamps for domestic uses, in toy making, in small electrical motors, as loudspeaker magnets. According to the magnetic properties, hard ferrites are grouped into two categories termed as“isotropic”and“anisotropic”ferrites. In isotropic ferrites, the material shows equal magnetic properties in all directions. The permanent magnetization (Br) in these ferrites is in the order of 0.2 Tesla (2000 Gauss) and depending on the production method, the coercive force (He) ranges from 12.10r to 16.10* Ampere/m (1500-2000 Oersted), In anisotropic ferrites, the magnetic properties are developed in only one direction by employing special pressing techniques under high magnetic fields. Such ferrites have permanent magnetization in the range of 0.3 - 0.4 Tesla (3000-4000 Gauss) an coercivity varies between varies between 16sl0* to 24*10' Ampere/m (2000-3000 Oersted),The optimum magnetic properties in hard ferrites are usually obtained at Fe,0* contents slightly lower than the stoichiometric formulation (n99.5% purity, Merck, Germany) and hematite (EVA &.Ş.) were weighed according to the formulation. The raw materials were then ball milled in distilled water at 60 rpm for 8 hours, using a 3 1 capacity steel jar and steel cylindrical balls of 2 cm diameter; 3 cm length. The mixture was then dried at 110°C and kept in sealed jars as stock composition. Boric acid used as BjOj additive (hight purity, Etibank, Turkey), was weighed out in the quantities listed in Table 2, in order to achieve the following formula, BaO. 5. 6Fe20j+x(B20j), x=0, 0.01, 0.05, 0.1, 0.15 and 0.2 mole. Table 2: HjBOj used per 100 g. stock ferrite formulation. The weighed boric acid, 100 g stock ferrite powder and 1 g of PVA (used as a binder) were then mixed in 100 ml. of distilled water. The mixture was dried to 6-10% humidity and then granulated to -74um. From the granulated powders, cylindrical samples of 16 mm. diameter 8 mm. in thickness were pressed at 30 MPa. These samples were calcined at 750, 800, 850, 900 and 1000°C for 1 hour, using 200°C/h heating rate and self wooled in the furnace. The calcined samples were then tested by x-ray diffraction to determine the unreacted Fe20j phase. The amount of the unreacted Fe20j phases for the undopped and 0.2 mole B2O» doped samples which were calculated from the ratio of maximum intensity peaks of barium hexaferrite ( dQfln = 2.7 &fl) and a-Fe20j (dnfl|j = 2.782 AS ) are given in Table 3. VllTable 3: Amount of unreacted a-Fe20j phase in calcined samples. As can be seen from table 3, the B2O3 addition clearly promotes the formation of the barium hexaferrite phase. Due to these encouraging results, it was decided to omit the calcination step from the manufacturing process. For this reason the research was focused on the effect of a B}0% addition on the magnetic properties of the direct-sintered samples. To study the direct sintering method, specimens in the above mentioned dimensions were pressed in a floating die system at a pressure of 100 MPa to a green density of 2,7«103 kg/m3. The sintering was carried out at 1100 - 1150 °C for 1-4 hours and at 1200, 1250 °C for 1 hour, in a SiC heated furnace in an atmospheric condition, employing a 200 °C/h heating rate. The bulk densities of the samples were determined from their mass and volume ratio. The microstructures were studied in a Jeol 840 scanning electron microscope and the magnetic properties were measured in permagraph equipment by Magnet-Physik (Köln - Germany). The effect of the B
Benzer Tezler
- B2O3 katkısının sentetik volastonit üretimi üzerine etkilerinin araştırılması
Researching the effects of B2O3 addition on synthetic vollastonite production
MURADİYE AĞAOĞLU
Yüksek Lisans
Türkçe
2006
Seramik MühendisliğiAfyon Kocatepe ÜniversitesiSeramik Mühendisliği Ana Bilim Dalı
DOÇ. DR. ALİ KARTAL
- Düşük kayıp faktörlü steatit seramiğinin dielektrik özelliklerine B2O3 katkısının etkisi
The effect of B2O3 adding on the dielektric properties of the steatite ceramic having the loss factor
ZEHRA ERDEM
Yüksek Lisans
Türkçe
2009
Fizik ve Fizik MühendisliğiSakarya ÜniversitesiFizik Ana Bilim Dalı
YRD. DOÇ. DR. ERDOĞAN ŞENTÜRK
- Spark plazma sinterleme yöntemi ile ışık geçirgenliğine sahip magnezyum alüminat spinel seramiklerinin üretimi ve karakterizasyonu
Production and characterization of magnesium aluminate spinel ceramics with ligth transmission by spark plasma sintering
SEYRAN SARIDAŞ
Yüksek Lisans
Türkçe
2016
Seramik Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. FİLİZ ŞAHİN
- Biyodizel n-oktanol yakıt karışımına nanopartikül ilavesinin motor performansı ve yanma üzerine etkisinin incelenmesi
Investigation of the effect of adding nanoparticles to biodiesel n-octanol fuel mixture on engine performance and combustion
GÜVEN DEMİRTAŞ
Doktora
Türkçe
2023
Makine MühendisliğiMarmara ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. CENK SAYIN
DR. ÖĞR. ÜYESİ MUSTAFA KEMAL BALKİ
- Bor oksit katkılı somon kalsiyum fosfat esaslı biyoseramik kompozitlerin özellikleri ve karakterizasyonu
Properties and characterization of boron oxide doped salmon calcium phosphate based bioceramic composites
MERVE BAŞ
Yüksek Lisans
Türkçe
2021
BiyomühendislikYıldız Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. SİBEL DAĞLILAR
DR. ÖĞR. ÜYESİ CEVRİYE KALKANDELEN