Mil konstrüksiyonlarında çentik etkisi ve önlenmesi için alınacak konstrüktif tedbirler (yorulma dizaynı
Başlık çevirisi mevcut değil.
- Tez No: 57938
- Danışmanlar: PROF. DR. İSMAİL GÜRGÜL
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: Çentik Etkisi, Gerilim Yığılma Faktörü, Mil Dizaym, Yorulma
- Yıl: 1996
- Dil: Türkçe
- Üniversite: Kocaeli Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: Makine Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 124
Özet
MİLLERDE ÇENTİK ETKİSİ VE ÖNLENMESİ İÇİN ALINACAK KONSTÜKTİF TEDBİRLER(YORULMA DİZAYNI) KAYHAN KOCA
Özet (Çeviri)
FATİGUE DESING OF SHAFTS KAYHAN KOCA Keywords :Notch Effects, Stress Concentration Factor,Shaft Desing.fatıgue. The machine components have to withstandfrequent load variations. We can see many examples"the load on vehicles and transport equipment,power generatos and converts,machine tools etc. 4-ti At the begining of the 18 century many problem wich were seen producing the steels were tried to solve by researchers and problems of course were given the machine equipment with this steels.During researhing steel problems of the machine components. It was BACH on the evidence of wohlers test first divided the permissible stresses for steel 'into three categories. Static,Fluctuating,reversed This classification was in general use for long time and it's still applicable in cases when special accuracy is not requried. In our project we have researched fatigue problems of the shafts how to avoid and how to desing according to fatigue. Ill
Benzer Tezler
- MIL DTL 46100 sınıfı zırh çeliklerinin farklı dolgu malzemeleri kullanılarak yapılan kaynak işleminde ön ısıtma gerekliliğinin araştırılması
Investigation of pre-heating requirements of the MIL DTL 46100 class armour steels welding by using different filler materials
ESAT KOSTAK
Yüksek Lisans
Türkçe
2021
Metalurji MühendisliğiSelçuk ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. MUSTAFA ACARER
- Keten ve keten/selülozik elyaf karışımlarının reaktif, direkt ve kükürt boyarmaddelerle boyanması
Dyeing of %100 linen and linen/cellulosic blends with reactive, direct and sulphur dyes
MEHMET ÖNDER AKTAŞ
Yüksek Lisans
Türkçe
2008
Teknik EğitimMarmara ÜniversitesiTekstil Eğitimi Ana Bilim Dalı
DOÇ. DR. NİHAL SÖKMEN
- Mil-göbek bağlantılarında boyut ölçüm analiz yöntemlerinin etkinliğinin eksenel yük iletimine bağlı olarak numerik ve deneysel incelenmesi
Numerical and experimental investigation of the effectiveness of dimensional measurement analysis methods in shaft-hub connections according to axial load transmission
ENES FURKAN YİĞİT
Yüksek Lisans
Türkçe
2022
Otomotiv MühendisliğiKocaeli ÜniversitesiOtomotiv Mühendisliği Ana Bilim Dalı
DOÇ. DR. ABDULKADİR CENGİZ
- Anomaly detection of MIL-STD 1553 traffic: Machine learning methods and realistic simulation evaluation
MIL-STD 1553 trafiğinde anomali tespiti: Makine öğrenmesi yöntemleri ve gerçekçi simülasyon ile değerlendirme
HÜSEYİN SAĞIRKAYA
Yüksek Lisans
İngilizce
2023
Elektrik ve Elektronik MühendisliğiOrta Doğu Teknik ÜniversitesiElektrik-Elektronik Mühendisliği Ana Bilim Dalı
PROF. DR. ECE GÜRAN SCHMİDT
- Fuzzy control of distillation column using qualitative modelling
Başlık çevirisi yok
HALİL MURAT ÖZTÜRK