Wedge shear testing of clayey gravels under higher normal stresses
Killi çakılların kesme dayanımlarının yüksek gerilmeler altında ölçülmesi
- Tez No: 68574
- Danışmanlar: PROF. DR. TÜRKER MİRATA
- Tez Türü: Yüksek Lisans
- Konular: İnşaat Mühendisliği, Civil Engineering
- Anahtar Kelimeler: Kil, Silt, Çakıl, Kesme Deneyi, Üç Eksenli Deney, Kama Kesme Deneyi vuı, Clay, silt, Gravel, Shear strength, Laboratory Shear test, Triaxial Test, Shear Test
- Yıl: 1997
- Dil: İngilizce
- Üniversite: Orta Doğu Teknik Üniversitesi
- Enstitü: Fen Bilimleri Enstitüsü
- Ana Bilim Dalı: İnşaat Mühendisliği Ana Bilim Dalı
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 153
Özet
oz KİLLİ ÇAKILLARIN KESME DAYANIMLARININ YÜKSEK GERİLMELER ALTINDA ÖLÇÜLMESİ SAKAR, Mehmet Yüksek Lisans, İnşaat Mühendisliği Bölümü Supervisor: Prof. Dr. Türker MİRATA Temmuz 1997, 153 sayfa Kama kesme deneyindeki dikey gerilme a'nın kabaca (ctn+(t>) toplamına bağlı olarak arttığı önceden gösterilmişti; burada, an = kalıbın kesme düzlemi ile ana yük arasındaki açı, = 89.5° değerini aşmadan denenebilmesine olanak sağlayacak biçimde kalıbın etkili açısı yeterince düşürülebilmiş, dikey gerilme, 45°' lik kalıp kullanılarak elde edilen değerin yaklaşık iki katına çıkarılabilmiştir. vııAyrıca, 3 numaralı numune üzerinde büyük ölçekli üç eksenli deneyler yapılmış ve sonuçlar aynı su içeriğinde ve sıkılıkta elde edilen prizmatik kama kesme deneylerinde elde edilenlerle karşılaştınlmıştır.
Özet (Çeviri)
ABSTRACT WEDGE SHEAR TESTING OF CLAYEY GRAVELS UNDER HIGHER NORMAL STRESSES SAKAR, Mehmet M.Sc, Department of Civil Engineering Supervisor: Prof. Dr. Türker MİRATA July 1997,153 pages It had already been shown that the normal stress a in the wedge shear test increases roughly as a function of the sum (an+(|)), where an = the angle between the shearing plane of the test mould and the main load; § = angle of internal friction of the soil tested, but that increase is limited. When this sum is greater than about 89.5°, it is impossible to shear the soil along the prescribed failure plane. In one of the previous prismatic wedge shear tests (priswests) on well graded clean gravel containing particles up to 38 mm, it had been shown that the normal stress (a) could be increased up to 953 kPa under a lateral load of 0.24 kN by 111using a 45° test mould. However, the angle of internal friction of 46° obtained in these tests could not be obtained for silty and clayey gravels. So, the only way of increasing the normal stress for such soils was to increase the mould angle. It had already been proposed that it was possible to apply some simple modifications to a 40° mould, which was already available, and use it as one having aa = 50°. The primary aim of this study was to show the applicability of that proposal experimentally. The proposed modifications were applied, enabling the 40° mould to be used as a 50° one, when desired. This 50° mould was used to test three different gravels, having different proportions of fine material by dry weight of the mixture. Tests on sample 3, having proportions of 20 % particles passing 1 mm sieve and 80 % gravel between 19 mm and 38 mm, have shown that o could be extended up to 848 kPa compared to 325 kPa obtained by using the 45° mould. As a further innovation in this study, the three spacers, having different thicknesses were used together to increase the spacing between the two halves of the 50° mould to 25 mm, twice the maximum spacing so far used. The effective mould angle could thus be reduced sufficiently to test sample 1, containing 15 % particles passing 74 (im sieve and 85 % gravel between 5 mm and 25 mm, and having = 40° by using the 50° mould without exceeding the a" + § = 89.5° limit. Hence, the normal stresses could be extended by almost twice that obtained using the 45° mould. IVLarge scale drained triaxial tests on the third sample were also performed and the results were compared with those of priswests at the same water content and the degree of compaction.
Benzer Tezler
- A study on the box size and orientation effects on direct and interface shear tests
Direkt ve arayüz kesme testlerinde kutu boyutu ve oryantasyon etkileri üzerine bir çalışma
SUAD MERT GÜMÜŞALAN
Yüksek Lisans
İngilizce
2021
İnşaat MühendisliğiBoğaziçi Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. İBRAHİM GÖKHAN BAYKAL
- Use of the cylindrical wadge shear test for the compoction control of clay fills
Başlık çevirisi yok
MUSTAFA VARAN
- Effect on shear strength of the clearance between the two halves of the prismatic wedge shear test mould
Prizmatik kama kesme deneyi kalıbının iki yarısı arasındaki açıklığın kayma dayanımına etkisi
T. EMRİN FİLİZ
Yüksek Lisans
İngilizce
2000
İnşaat MühendisliğiOrta Doğu Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. TÜRKER MİRATA
- Comparison of the shear strength of statically and dynamical compacted clays
Statik ve dinamik olarak sıkıştırılmış killerin kayma mukavemetlerinin karşılaştırılması
KADİR FIRAT GÜN
Yüksek Lisans
İngilizce
1997
İnşaat MühendisliğiOrta Doğu Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. TÜRKER MİRATA
- Effect of curing on the undrained shear strength of compacted clays
Sıkıştırılmış killerde örneği sabit nemde bekletmenin drenajsız kayma dayanımına etkisi
ALP GÜROL
Yüksek Lisans
İngilizce
2000
İnşaat MühendisliğiOrta Doğu Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. TÜRKER MİRATA