School of mechanical and design engineering
Başlık çevirisi mevcut değil.
- Tez No: 714687
- Danışmanlar: DR. BURHAN SAEED
- Tez Türü: Yüksek Lisans
- Konular: Makine Mühendisliği, Mechanical Engineering
- Anahtar Kelimeler: gurney flap, aerofoil, slat, flap, nhlp
- Yıl: 2021
- Dil: İngilizce
- Üniversite: University of Portsmouth
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 108
Özet
Özet yok.
Özet (Çeviri)
A two-dimensional RANS based numerical investigation was performed to determine the aerodynamic performance of a gurney flap on a multi-element aerofoil. These flaps are rectangular shaped and located perpendicularly at the trailing edge of the aerofoil. By comparing with numerical data without gurney flap aerofoils, such as the lift-drag coefficient, and the pressure-velocity distribution, the simulation method has verified. Tested aerofoils are NACA 0012, NACA 23012 slotted flap and NHLP (National High Lift Programme). The attached gurney flap size ranges from 1% to 2% of the aerofoil chord length and the investigation was evaluated between 0° and 20° angle of attack. Additionally, the slat and flap elements in the NHLP (National High Lift Program) aerofoil were compared by including the gurney flap with different deflection angles. It is recommended that gurney flaps size of 1% chord with using at lower angles of attack and take-off stage to gain maximum lift increase with minimum drag penalty. For the landing stage, it is understood that the gurney flap increases the friction due to the increase in the area covered by the air flow, thus helping the landing by shortening the braking distance.
Benzer Tezler
- T-37 uçağı için kanopi tasarımı ve imalatı
Design and manufacturing of canopy for T-37 aircraft
BÜLENT UZUN
Yüksek Lisans
Türkçe
2006
Makine MühendisliğiNiğde ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
Y.DOÇ.DR. FAHRETTİN ÖZTÜRK
- Güç ölçümü deney düzeneği tasarım ve imalatı
Design and manifacture of an experimental set up power measurement
MURAT DİLMEÇ
Yüksek Lisans
Türkçe
2004
Makine MühendisliğiNiğde ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
DOÇ.DR. OSMAN YİĞİT
- Boru-gövde tipi tek fazlı ısı eşanjörlerinin bilgisayar yardımıyla tasarımı
A Project about computer aided design of single phase shell and tube type heat exchangers
ÖZBİLEN GÜRARAS
Yüksek Lisans
Türkçe
2002
Makine MühendisliğiAtatürk ÜniversitesiMakine Ana Bilim Dalı
YRD. DOÇ. DR. YUSUF ALİ KARA
- Mini-disk keskili bomlu kazı makinelerinin stabilite analizi
Stability analysis of a mini-disc equipped boom type tunneling machine
CEMALETTİN ERDOĞAN
Yüksek Lisans
Türkçe
2015
Maden Mühendisliği ve Madencilikİstanbul Teknik ÜniversitesiMaden Mühendisliği Ana Bilim Dalı
DOÇ. DR. ÖMÜR ACAROĞLU ERGÜN
- Dalgıç pompalar ve fan tasarım esasları
Submersible pumps and fan design principles
BİLAL KÜBİLAY YAŞAR
Yüksek Lisans
Türkçe
1997
Makine MühendisliğiHarran ÜniversitesiMakine Ana Bilim Dalı
DOÇ. DR. CEMAL OKUYAN