Strain measurements on Fe, Niand NiFe embedded carbon fiberepoxy composite
Başlık çevirisi mevcut değil.
- Tez No: 717481
- Danışmanlar: PROF. NİCOLA MORLEY
- Tez Türü: Yüksek Lisans
- Konular: Kimya Mühendisliği, Chemical Engineering
- Anahtar Kelimeler: Belirtilmemiş.
- Yıl: 2020
- Dil: İngilizce
- Üniversite: The University of Sheffield
- Enstitü: Yurtdışı Enstitü
- Ana Bilim Dalı: Belirtilmemiş.
- Bilim Dalı: Belirtilmemiş.
- Sayfa Sayısı: 48
Özet
Özet yok.
Özet (Çeviri)
The magnetisations of a woven carbon/epoxy composite embedded with ~1 volume percent of Fe, Ni and NiFe powder particles (6-200 µm) were measured at the tensile strains from 0.833 to 1.6 mstrain. The powder embedded composite test plates (1x25x50 mm) were strained using a bending ring test apparatus with various bend radius. The magnetisation of loaded composite samples was measured before and during loading using a 3D Anisotropic Magneto-Resistance sensor in three directions. The maximum change of magnetisation was measured in the z-axis, normal to the loading direction, and there was almost no change of magnetisation in x and yaxis. The total change of magnetisation was found to be parallel with the change of magnetisation in the z-axis. The composites embedded with the particles less than 80 µm showed an increasing change of magnetisation with increasing bending strain. The determined piezo-magnetic stress and strain coefficients of the composites embedded with less than 80 µm particles were shown to be similar with those of similar composites tagged with Terfenol-D particles. The results also showed that magnetic Fe and Ni particle addition to composites can be used to measure strain within the composites remotely for structural health monitoring. The errors in magnetisation measurements including the sensor-sample distance and the stress state (reduction of the tensile stress in the thickness direction) are discussed. In order to prevent the stress state effect, powder addition to only the upper and lower surfaces of the composite plate is recommended. The studied powder added composite should be further investigated for optimum powder size in order to increase the accuracy of magnetisation measurements.
Benzer Tezler
- Optimization of fragmentation behaviour of brittle phase in a ductile matrix during mechanical alloying for the production of nano composite powders and final products
Mekanik alaşımlama sırasında gevrek fazın sünek matris içerisindeki ufalanma davranışlarının optimize edilmesi ve nano kompozit tozu nihai ürün üretimi
AYDIN ŞELTE
Doktora
İngilizce
2019
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. BURAK ÖZKAL
- Kendiliğinden ilerleyen yüksek sıcaklık sentezi yöntemi ile yeni ve özel alaşımların üretimi ve geliştirilmesi
Investigation of new and noble alloys productions by self-propagating high-temperature synthesis method
MURAT ALKAN
Doktora
Türkçe
2014
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. ONURALP YÜCEL
DOÇ. DR. CEVAT BORA DERİN
- Kobalt esaslı alaşımların bağlayıcı matris olarak kullanıldığı doğal taş kesiminde kullanılan elmas kesici uçların karakterizasyonu
Characterization of diamond cutting tools using cobalt base alloys as the binding matrices
FERİT TOPALOĞLU
Yüksek Lisans
Türkçe
2013
Metalurji Mühendisliğiİstanbul Teknik ÜniversitesiMetalurji ve Malzeme Mühendisliği Ana Bilim Dalı
PROF. DR. EYÜP SABRİ KAYALI
- Ağır ticari araçların havalı süspansiyon sisteminde kullanılan boru denge çubuğu tasarımı
Design of hollow anti-roll bar for heavy duty vehicle air suspension systems
NESLİHAN SAYILGAN
Yüksek Lisans
Türkçe
2015
Makine Mühendisliğiİstanbul Teknik ÜniversitesiMakine Mühendisliği Ana Bilim Dalı
PROF. DR. EKREM TÜFEKCİ
- Beton üstü asfalt kaplamalarda oluşan yansıma çatlaklarının incelenmesi
Investigation of reflective cracking of asphalt overlay on concrete pavements
MEHMET TEVFİK SEFEROĞLU
Doktora
Türkçe
2019
UlaşımKaradeniz Teknik Üniversitesiİnşaat Mühendisliği Ana Bilim Dalı
PROF. DR. MUHAMMET VEFA AKPINAR